RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Workshop Manual

13B-261V9 MR-372-J84-13B450$140.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
* diff: differential
* temp: temperatureTool parameter Diagnostic tool title
PR385Exhaust pipe flow
PR391Mileage since particle filter replacement
PR405Cylinder no. 2 fuel flow correction
PR406Cylinder no. 3 fuel flow correction
PR412Mileage at last successful regeneration
PR414Particle filter pressure diff.*
PR415Time since last regeneration
PR420Damper valve error counter
PR667Turbine upstream temperature
PR668Turbine upstream temperature sensor voltage
PR672Damper valve position setpoint
PR747Damper valve position
PR777Richness ratio sensor voltage
PR778Richness ratio sensor temp.*
PR779Richness ratio
PR784DF312 recording No. 1
PR785DF312 recording No. 2
PR786DF312 recording No. 3
PR787DF312 recording No. 4
PR788DF312 recording No. 5
PR789DF312 recording No. 6
PR790DF312 recording No. 7
PR791DF312 recording No. 8
PR792DF312 recording No. 9
PR793DF312 recording No. 10
PR794Stored regeneration failure no. 1
PR795Stored regeneration failure no. 2
PR796Stored regeneration failure no. 3

13B-262V9 MR-372-J84-13B450$140.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Tool parameter Diagnostic tool title
PR797Stored regeneration failure no. 4
PR798Stored regeneration failure no. 5
PR799Stored regeneration failure no. 6
PR800Stored regeneration failure no. 7
PR801Stored regeneration failure no. 8
PR802Stored regeneration failure no. 9
PR803Stored regeneration failure no. 10
PR816No.1 regeneration start recording
PR817No.2 regeneration start recording
PR818No.3 regeneration start recording
PR819No.4 regeneration start recording
PR820No.5 regeneration start recording
PR821No.6 regeneration start recording
PR822No.7 regeneration start recording
PR823No.8 regeneration start recording
PR824No.9 regeneration start recording
PR825No.10 regeneration start recording
PR848Number of regeneration failures
PR873Oil oxidation signal
PR874Last service

13B-263
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR002ALTERNATOR CHARGE
PARAMETER
DEFINITIONThis parameter indicates the charge value of the alternator in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The alternator charge value varies according to the battery voltage.
EDC16C36_V44_PR002/EDC16C36_V4C_PR002/EDC16C36_V48_PR002/EDC16C36_V50_PR002/EDC16C36_V54_PR002/
EDC16C36_V58_PR002
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-264
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR005EGR VALVE OPENING SETPOINTS
PARAMETER
DEFINITIONThis parameter indicates a theoretical opening value for the EGR valve for optimum
engine performance.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on
The EGR valve theoretical opening value for operation with the engine stopped and ignition on is:
-10 Conformity check with engine running, engine coolant temperature > 80°C
The theoretical EGR valve opening value for operation with the engine running and engine coolant temperature
>80°C is 10 < PR005 < 40%
EDC16C36_V44_PR005/EDC16C36_V4C_PR005/EDC16C36_V48_PR005/EDC16C36_V50_PR005/EDC16C36_V54_PR005/
EDC16C36_V58_PR005EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-265
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR006RAIL PRESSURE REGULATOR CURRENT
PARAMETER
DEFINITIONThis parameter indicates the current absorbed by the rail pressure regulator.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
This parameter indicates the current absorbed by the rail pressure regulator PR006 ≈ PR007 Rail pressure
regulator current setpoint.
If there is a fault, consult the interpretation of fault DF643 Rail pressure regulator circuit.
EDC16C36_V44_PR006/EDC16C36_V4C_PR006/EDC16C36_V48_PR006/EDC16C36_V50_PR006/EDC16C36_V54_PR006/
EDC16C36_V58_PR006EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-266
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR007RAIL PRESSURE REGULATOR CURRENT SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the theoretical setpoint for the current absorbed by the rail
pressure regulator.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
This parameter indicates the theoretical current absorbed by the rail pressure regulator.
EDC16C36_V44_PR007/EDC16C36_V4C_PR007/EDC16C36_V48_PR007/EDC16C36_V50_PR007/EDC16C36_V54_PR007/
EDC16C36_V58_PR007EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-267
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR008RAIL REFERENCE PRESSURES
PARAMETER
DEFINITIONThis parameter indicates the theoretical rail pressure value for optimum engine
operation in bar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The theoretical rail pressure value is a setpoint, i.e. 200 < PR008 < 300 bar
EDC16C36_V44_PR008/EDC16C36_V4C_PR008/EDC16C36_V48_PR008/EDC16C36_V50_PR008/EDC16C36_V54_PR008/
EDC16C36_V58_PR008EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-268
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR009TURBOCHARGING PRESSURE SETPOINTS
PARAMETER
DEFINITIONThis parameter indicates the theoretical turbocharging pressure setpoint value in bar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The theoretical turbocharging pressure value is a setpoint, i.e. PR009 ≈ 1 bar
EDC16C36_V44_PR009/EDC16C36_V4C_PR009/EDC16C36_V48_PR009/EDC16C36_V50_PR009/EDC16C36_V54_PR009/
EDC16C36_V58_PR009EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-269
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR015ENGINE TORQUE
PARAMETER
DEFINITIONThis parameter indicates the engine torque in Nm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Engine running, engine coolant temperature > 80°C
This value must be between 20 N.m < PR015 < 40 N.m
This parameter is only valid when the engine is running.
EDC16C36_V44_PR015/EDC16C36_V4C_PR015/EDC16C36_V48_PR015/EDC16C36_V50_PR015/EDC16C36_V54_PR015/
EDC16C36_V58_PR015EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-270
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR017FUEL FLOW
PARAMETER
DEFINITIONThis parameter indicates the fuel flow in mg/st.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on
PR017 = 0 mg/st.
If there is a fault, consult the interpretation of fault DF643 Rail pressure regulator circuit.
Conformity check with engine running, engine coolant temperature > 80°C
PR017 = PR157 Fuel flow setpoint.
If there is a fault, consult the interpretation of fault DF643 Rail pressure regulator circuit.
EDC16C36_V44_PR017/EDC16C36_V4C_PR017/EDC16C36_V48_PR017/EDC16C36_V50_PR017/EDC16C36_V54_PR017/
EDC16C36_V58_PR017EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58