sensor RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Repair Manual

13B-126
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF165
CONTINUED 1
Check the condition of the pedal sensor connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component code 921).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector(s) is/are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the pedal sensor gang 1 between the following connections:
– Connection code 3LR of component 921.
– Connection code 3LT of component 921.
Replace the sensor if the resistance is not 1.2 kΩ ± 0.48 kΩ.
Measure the resistance of the pedal sensor gang 2 between the following connections.
– Connection code 3LU of component 921.
– Connection code 3LV of component 921.
Replace the sensor if the resistance is not 1.7 kΩ ± 0.68 kΩ.
Check the continuity and the absence of interference resistance of the following connections:
– Connection code 3LR between components 921 and 120.
– Connection code 3LS between components 921 and 120.
– Connection code 3LT between components 921 and 120.
– Connection code 3LU between components 921 and 120.
– Connection code 3LV between components 921 and 120.
– Connection code 3LW between components 921 and 120.
If there is a repair method (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-127
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF165
CONTINUED 2
3.DEFNOTESPriorities when dealing with a number of faults:
Deal with fault DF012 Sensor feed voltage no. 2 first, if it is
present or stored.
Conditions for applying the fault finding procedure to a
stored fault:
The fault occurs if the brake pedal and the accelerator pedal
are depressed simultaneously for more than 30 seconds
without any movement.
Special notes:
Do not interpret the conditions under which the fault occurs.
Make sure that the accelerator pedal is not mechanically jammed (broken spring, floor carpet, etc.).
Check that the brake switch is correctly positioned in its housing.
If the fault is still present, deal with fault DF165 2.DEF.
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-128
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF195
PRESENT
OR
STOREDENGINE SPEED/CAMSHAFT SENSOR CONSISTENCY
1.DEF: Signal incoherent
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
–10 seconds with the starter active,
– a delay of 1 minute with the engine running.
Special notes:
Use bornier Elé. 1681 for any operations on the computer connector.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
1.DEF
NOTESPriorities when dealing with a number of faults:
Apply the interpretation of faults DF119 Camshaft sensor
signal and DF120 Engine speed sensor signal first, if they
are present or stored.
Check the sensor mounting and the conformity of the camshaft target.
Check that the camshaft sensor/camshaft sprocket air gap is 3 mm maximum.
Check the engine speed sensor mounting.
Check the condition of the engine speed sensor and camshaft sensor connectors (see Wiring Diagram Technical
Note, Mégane II ph2, Scénic II ph2, component codes 149 and 746).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
– Check the tension of the timing belt.
– Check the conformity of the camshaft sprocket/camshaft assembly.
– Check the timing adjustment.
Carry out the necessary repairs.
If the fault is still present, contact the Techline.
EDC16C36_V44_DF195/EDC16C36_V4C_DF195/EDC16C36_V48_DF195/EDC16C36_V50_DF195/EDC16C36_V54_DF195/
EDC16C36_V58_DF195EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-129
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF196
PRESENT
OR
STOREDPEDAL SENSOR CIRCUIT GANG 1
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
1.DEF: Consistency between gang 1 and gang 2
NOTESPriorities when dealing with a number of faults:
Deal with fault DF011 Sensor supply voltage no. 1 first if it is present or stored
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after a series of full load / no load actions on the
accelerator pedal.
Special notes:
If the fault is present:
– engine torque limited,
– cruise control not authorised,
–the level 1 warning light is lit,
–the level 2 warning light is lit if 1.DEF and only if 2 gangs lost,
– the idle speed is 1400 rpm if 2 gangs lost.
Use bornier Elé.1681 for any operations on the computer connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF196/EDC16C36_V4C_DF196/EDC16C36_V48_DF196/EDC16C36_V50_DF196/EDC16C36_V54_DF196/
EDC16C36_V58_DF196EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-130
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF196
CONTINUED 1
CO.0NOTESDealing with a number of faults:
If there is a simultaneous occurrence of fault DF198 Pedal
sensor circuit gang 2, check that the pedal sensor
connector is connected correctly.
Check the condition of the pedal sensor connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component code 921).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector(s) is/are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the pedal sensor between the following connections:
– Connection code 3LR of component 921.
– Connection code 3LT of component 921.
Replace the sensor if the resistance is not 1.2 kΩ ± 0.48 kΩ.
Check the continuity and insulation from earth of the following connections:
– Connection code 3LR between components 921 and 120.
– Connection code 3LS between components 921 and 120.
– Connection code 3LT between components 921 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-131
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF196
CONTINUED 2
CC.1NOTESNone.
Check the condition of the pedal sensor connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component code 921).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the pedal sensor between the following connections:
– Connection code 3LR of component 921.
– Connection code 3LT of component 921.
Replace the sensor if the resistance is not 1.2 kΩ ± 0.48 kΩ.
Check the continuity and insulation from + 12 V and + 5 V (computer feeds) on the following connections:
– Connection code 3LR between components 921 and 120.
– Connection code 3LS between components 921 and 120.
– Connection code 3LT between components 921 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-132
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF196
CONTINUED 3
1.DEFNOTESNone.
Check the condition of the pedal sensor connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component code 921).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the pedal sensor between the following connections:
– Connection code 3LR of component 921.
– Connection code 3LT of component 921.
Replace the sensor if the resistance is not 1.2 kΩ ± 0.48 kΩ.
Check for continuity and absence of interference resistance of the following connections:
– Connection code 3LR between components 921 and 120.
– Connection code 3LS between components 921 and 120.
– Connection code 3LT between components 921 and 120.
– Connection code 3LU between components 921 and 120.
– Connection code 3LV between components 921 and 120.
– Connection code 3LW between components 921 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Check the insulation between the following connections:
– Connection code 3LS between components 921 and 120.
– Connection code 3LW
between components 921 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault is still present, vary the pedal position and consult the interpretation of parameters to check the
operating values of the accelerator pedal sensor.
If the values displayed are inconsistent, replace the accelerator pedal sensor.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-133
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF198
PRESENT
OR
STOREDPEDAL SENSOR CIRCUIT GANG 2
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
1.DEF: Consistency between gang 1 and gang 2
NOTESPriorities when dealing with a number of faults:
Deal with fault DF012 Sensor feed voltage no. 2 first, if it is present or stored.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after a series of full load / no load actions on the
accelerator pedal.
Special notes:
If the fault is present:
– engine torque is limited
– cruise control not authorised.
–the level 1 warning light is lit,
–the level 2 warning light is lit if 1.DEF and only if 2 gangs lost,
– the idle speed is 1400 rpm if 2 gangs lost.
Use bornier Elé.1681 for any operations on the computer connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF198/EDC16C36_V4C_DF198/EDC16C36_V48_DF198/EDC16C36_V50_DF198/EDC16C36_V54_DF198/
EDC16C36_V58_DF198EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-134
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF198
CONTINUED 1
CO.0NOTESDealing with a number of faults:
If there is a simultaneous occurrence of fault DF196 Pedal
sensor circuit gang 1, check that the pedal sensor
connector is connected correctly.
Check the condition of the pedal sensor connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component code 921).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector(s) is/are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the pedal sensor between the following connections:
– Connection code 3LU of component 921.
– Connection code 3LV of component 921.
Replace the sensor if the resistance is not 1.7 kΩ ± 0.68 kΩ.
Check the continuity and insulation from earth of the following connections:
– Connection code 3LU between components 921 and 120.
– Connection code 3LV between components 921 and 120.
– Connection code 3LW between components 921 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-135
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF198
CONTINUED 2
CC.1NOTESNone.
Check the condition of the pedal sensor connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component code 921).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the pedal sensor between the following connections:
– Connection code 3LU of component 921.
– Connection code 3LV of component 921.
Replace the sensor if the resistance is not 1.7 kΩ ± 0.68 kΩ.
Check the continuity and insulation from + 12 V and + 5 V (computer feeds) on the following connections:
– Connection code 3LU between components 921 and 120.
– Connection code 3LV between components 921 and 120.
– Connection code 3LW between components 921 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58