sensor RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Service Manual

13B-58V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF013
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE NO. 3
1.DEF: Above max threshold
2.DEF: Below minimum threshold
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
– the ignition is switched on,
– starting the engine,
– a road test.
Special notes:
If the fault is present,
– engine torque limited,
– the EGR function is inhibited by the engine management computer,
– turbocharger cut-off,
– increase in polluting emissions,
– the engine stops,
the level 2 and European On Board Diagnostic warning lights are lit.
Use bornier Elé. 1681 for all operations on the connectors of the engine management
computer.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF013/EDC16C36_V4C_DF013/EDC16C36_V48_DF013/EDC16C36_V50_DF013/EDC16C36_V54_DF013/
EDC16C36_V58_DF013
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-59V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF013
CONTINUED 1
1.DEFNOTESNone.
Note:
Supply no. 3 is for the following components:
– air flow sensor,
– rail pressure sensor.
Measure the feed voltage on the following sensors:
– Connection code 3KJ of component 799.
– Connection code 3LX of component 1032.
If the voltage is more than + 5.1 V, disconnect the sensor connectors one by one.
If, after disconnecting the air flow sensor, the voltage returns to normal,
Check the insulation against + 12 V of the following connection:
– Connection code 3KJ between components 120 and 799.
If, after disconnecting the rail pressure sensor, the voltage returns to normal,
Check the insulation against + 12 V of the following connection:
– connection code 3LX between components 120 and 1032.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Clear the faults created by the multiple disconnections.
Carefully examine the engine management computer connections (for conductive particles, bent pins).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-60V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF013
CONTINUED 2
2.DEFNOTESNone.
Note:
Supply no. 3 is for the following components:
– flow sensor,
– rail pressure sensor.
Measure the feed voltage on the following sensors:
– Connection code 3KJ of component 799.
– Connection code 3LX of component 1032.
If the voltage is below 4.9 V, disconnect the sensor connectors one by one.
If, after disconnecting the air flow sensor, the voltage returns to normal,
check the insulation to earth of the following connection:
– Connection code 3KJ between components 120 and 799.
If, after disconnecting the rail pressure sensor, the voltage returns to normal,
check the insulation to earth of the following connection:
– connection code 3LX between components 120 and 1032.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Clear the faults created by the multiple disconnections.
Carefully examine the engine management computer connections (for conductive particles, bent pins).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-85V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF051
PRESENT
OR
STOREDCRUISE CONTROL/SPEED LIMITER
1.DEF: Cruise control or speed limiter fault.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– a road test with activation of the cruise control/speed limiter function.
– the engine is started.
Special notes:
If the fault is present, the cruise control/speed limiter is switched off.
Use bornier Elé.1681 for any operations on the injection computer connectors.
1.DEF
NOTESOrder of priority for a combination of faults:
Deal with faults DF196 Pedal sensor circuit gang 1 and
DF198 Pedal sensor circuit gang 2 first if they are stored.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This check enables the condition and the conformity of the engine wiring harness to be checked.
If fault DF051 is declared present, consult the interpretation of status ET415 Cruise control/speed limiter
deactivation.
Check that by pressing the buttons the statuses change and that, with the ignition switched on, all the values are
correct.
If the fault is still present, contact the Techline.
EDC16C36_V44_DF051/EDC16C36_V4C_DF051/EDC16C36_V48_DF051/EDC16C36_V50_DF051/EDC16C36_V54_DF051/
EDC16C36_V58_DF051
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-87V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF053
CONTINUED
In the event of rail overpressure:
Check the operation of the injectors (see Test 10 Incorrect injector operation).
Display parameter PR038 Rail pressure and refer to the conformity check to check the conformity of the operating
values.
If these checks do not indicate any abnormality and if the fault persists, replace the injection pump.
In the event of rail vacuum pressure:
Check that the rail pressure sensor is operating correctly using command AC011 Rail pressure regulator. Display
parameter PR038 Rail pressure and refer to the conformity check to check the conformity of the operating values.
Check the priming of the low-pressure diesel circuit.
Check the conformity of the diesel filter connections.
Check the condition of the filter (clogging and water saturation).
Check that there are no air bubbles between the filter and the high pressure pump.
Check the seal of the low and high pressure diesel circuits (visual checks, odour, etc.), pump body, overpressure
valve, pipes, rail and injector unions, injector wells, etc.
Check the operation of the injectors (see Test 10 Incorrect injector operation).
Carry out the necessary operations.
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-93V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF055
PRESENT
OR
STOREDTURBOCHARGING PRESSURE REGULATION CIRCUIT
1.DEF: Turbocharging pressure too high
2.DEF: Turbocharging pressure too low
NOTESPriorities when dealing with a number of faults:
Deal with faults DF054 Turbocharger solenoid valve control circuit and DF004
Turbocharging pressure sensor circuit first, if they are present or stored.
Conditions for applying the fault finding procedure to a stored fault:
In the negative loop difference phase.
The fault is declared present after:
– the ignition is switched on.
– starting the engine,
– a road test.
Special notes:
If the fault is present:
– engine torque limited,
– turbocharging regulation is inhibited,
– the EGR function is inhibited,
– increase in polluting emissions,
– activation of the EGR bypass,
– the injection level 1 warning light is on.
Use bornier Elé.1681 for any operations on the injection computer connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF055/EDC16C36_V4C_DF055/EDC16C36_V48_DF055/EDC16C36_V50_DF055/EDC16C36_V54_DF055/
EDC16C36_V58_DF055
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-94V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF055
CONTINUED
1.DEF
2.DEFNOTESNone.
Check the condition of the turbocharging pressure sensor connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 1071).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Check the continuity and absence of interference resistance of the following connections:
– connection code 3LP between components 1071 and 120.
– connection code 3LQ, between components 1071 and 120.
– connection code 3LN between components 1071 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
With the engine stationary and ignition on, display parameters PR035 Atmospheric pressure and PR041
Turbocharging pressure.
If there is a difference of > 100 mbar, check that the atmospheric pressure read is consistent (by comparing the
value with that of another vehicle for example).
If atmospheric pressure is consistent, replace the turbocharging sensor.
If not, contact the Techline.
Apply test 4: Turbocharged air inlet circuit check.
If the fault is still present, refer to the interpretation of parameter PR041 Turbocharging pressure.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-95V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF056
PRESENT
OR
STOREDAIR FLOW SENSOR CIRCUIT
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit + 12 volts
1.DEF: Value outside permitted tolerance values
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on.
– starting for CC.1 and continuously for CO.0,
– a road test,
– the ignition is switched off: 1.DEF
Special notes:
If the fault is present:
–the level 1 warning light is lit,
– the EGR function is inhibited,
Use bornier Elé. 1681 for all operations on the engine management computer
connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF056/EDC16C36_V4C_DF056/EDC16C36_V48_DF056/EDC16C36_V50_DF056/EDC16C36_V54_DF056/
EDC16C36_V58_DF056
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-96V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF056
CONTINUED 1
CO.0NOTESPriorities when dealing with a number of faults:
In the event of the simultaneous presence of fault DF002 Air
temperature sensor circuit, check that the air flow sensor
connector is connected correctly.
Deal with fault DF013 Sensor supply voltage no. 3, 1.DEF
first, if it is present or stored.
Check the condition of the air flowmeter connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component code 799).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation to earth of the following connections:
– Connection code 3DW between components 799 and 120.
– Connection code 3DV between components 799 and 120.
– Connection code 3KJ between components 799 and 120.
Check for the presence of the + 5 V feed on the air flowmeter connector.
– Connection code 3KJ of component 799.
Check for the + 12 V feed on the air flowmeter connector.
– Connection code 3DV of component 799.
Apply test 5 Air flowmeter
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
With the flowmeter connected, the vehicle ignition on and engine stopped:
Check the voltage between the following connections:
– Connection code 3DW of component 799.
– Connection code 3DV of component 799.
If the voltage is not approximately 0.6 V ± 0.1 V, replace the air flowmeter.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the air flowmeter.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-97V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF056
CONTINUED 2
CC.1NOTESPriorities when dealing with a number of faults:
Deal with fault DF013 Sensor supply voltage no. 3, 1.DEF
first, if it is present or stored.
Check the condition of the air flowmeter connector (see Wiring Diagram Technical Note, Mégane II ph2, Scénic
II ph2, component code 799).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation in relation to + 12 V of the following connections:
– connection code 3DW between components 799 and 120.
– Connection code 3DV between components 799 and 120.
– Connection code 3KJ between components 799 and 120.
Check for the presence of the + 5 V feed on the air flowmeter connector.
– Connection code 3KJ of component 799.
Check for the + 12 V feed on the air flowmeter connector.
– Connection code 3DV of component 799.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
With the flowmeter connected, the vehicle ignition on and engine stopped:
Check the voltage between the following connections:
– Connection code 3DW of component 799.
– Connection code 3DV of component 799.
If the voltage is not approximately 0.6 V ± 0.1 V, replace the air flowmeter.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the air flowmeter.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58