air filter RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Service Manual

13B-236
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR412
DISTANCE VALUE AT LAST SUCCESSFUL REGENERATION
PARAMETER
DEFINITIONThis parameter indicates the last successful regeneration in miles (km).
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Mileage counter since last dynamic regeneration (when driving).
After all procedures have been carried out on the particle filter, use RZ030 Particle filter adaptive.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR412/SID304_V45_PR412/SID304_V49_PR412/SID301_V4C_PR412

13B-237
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR414
PARTICLE FILTER PRESSURE SENSOR
PARAMETER
DEFINITIONThis parameter indicates the particle filter differential pressure in mbar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
The differential pressure monitors the status of the particle weight in the filter.
The differential pressure of the particle filter is given in mbar.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR414/SID304_V45_PR414/SID304_V49_PR414/SID301_V4C_PR414

13B-238
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR415
TIME SINCE LAST REGENERATION
PARAMETER
DEFINITIONThis parameter indicates the time since the last regeneration in days.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Time counter since last active regeneration (when driving) in days.
After all procedures have been carried out on the particle filter, use RZ030 Particle filter adaptive.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR415/SID304_V45_PR415/SID304_V49_PR415/SID301_V4C_PR415

13B-244
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
*sens: sensor
*Circ: circuit
*diff: differential
*Press: PressurePR669
PARTICLE FILTER DIFF* PRESS* SENS* VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the voltage of the particle filter differential pressure sensor in
volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
PR669 ≈5V
In the event of a fault, consult the interpretation of DF1003 Particle filter differential pressure sensor circuit.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR669/SID304_V45_PR669/SID304_V49_PR669/SID301_V4C_PR669

13B-245
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
*temp: temperature
*sens: sensorPR670
VOLTAGE OF PARTICLE FILTER UPSTREAM OF TEMP* SENS*
PARAMETER
DEFINITIONThis parameter indicates the particle filter upstream temperature sensor voltage in
volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
0.7 V ≤PR670 ≤5V
In the event of a fault, refer to the interpretation of fault DF1000 Particle filter upstream temperature sensor
circuit.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR670/SID304_V45_PR670/SID304_V49_PR670/SID301_V4C_PR670

13B-246
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
*temp: temperature
*sens: sensorPR671
PARTICLE FILTER DOWNSTREAM TEMPERATURE SENS*
VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the particle filter downstream temperature sensor voltage in
volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
0.7 V ≤PR671 ≤5V
In the event of a fault, refer to the interpretation of fault DF999 Particle filter downstream temperature sensor
circuit.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR671/SID304_V45_PR671/SID304_V49_PR671/SID301_V4C_PR671

13B-249
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR794
PR795
PR796
PR797
PR798
PR799
PR800
PR801
PR802
PR803REGENERATION FAILURE RECORD NO. 1
REGENERATION FAILURE RECORD NO. 2
REGENERATION FAILURE RECORD NO. 3
REGENERATION FAILURE RECORD NO. 4
REGENERATION FAILURE RECORD NO. 5
REGENERATION FAILURE RECORD NO. 6
REGENERATION FAILURE RECORD NO. 7
REGENERATION FAILURE RECORD NO. 8
REGENERATION FAILURE RECORD NO. 9
REGENERATION FAILURE RECORD NO. 10
SPECIFICATION OF
THE PARAMETERSThese parameters indicate the regeneration failure record in miles (km).
NOTESSpecial note:
Check the interpretation of these parameters only on ALP21 Particle filter warning
light illuminated.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
these parameters are used so that the history of the last ten regeneration failures when driving are known.
Each parameter from PR794 to PR803 records the distance when regeneration fails and the engine status is
recorded by ET706 Stored engine status no. 1 to ET715 Stored engine status no. 10 (for example: PR797
Stored regeneration failure no. 4 is associated with ET709 Stored engine status no. 4).
The value is saved in the next parameter (PR+1) each time a new save is performed.
The distance of the last regeneration failures when driving are recorded in the other available parameters
(distance information in PR794 is recopied in PR795 and distance information in PR795 is recopied in PR796 and
so on).
When all ten parameters have a value other than zero, and a failed regeneration occurs when driving, the
distance information for PR794 Regeneration failure record No.1 is erased and replaced by the new value.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR794/SID304_V4D_PR795/SID304_V4D_PR796/SID304_V4D_PR797/SID304_V4D_PR798/SID304_V4D_PR799/
SID304_V4D_PR800/SID304_V4D_PR801/SID304_V4D_PR802/SID304_V4D_PR803/SID304_V49_PR794/SID304_V49_PR795/
SID304_V49_PR796/SID304_V49_PR797/SID304_V49_PR798/SID304_V49_PR799/SID304_V49_PR800/SID304_V49_PR801/
SID304_V49_PR802/SID304_V49_PR803/SID301_V4C_PR794/SID301_V4C_PR795/SID301_V4C_PR796/SID301_V4C_PR797/
SID301_V4C_PR798/SID301_V4C_PR799/SID301_V4C_PR800/SID301_V4C_PR801/SID301_V4C_PR802/SID301_V4C_PR803

13B-252
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR836
PR837
PR838
PR839
PR840
PR841
PR842
PR843
PR844
PR845PARTICLE FILTER WARNING LIGHT RECORD NO. 1
PARTICLE FILTER WARNING LIGHT RECORD NO. 2
PARTICLE FILTER WARNING LIGHT RECORD NO. 3
PARTICLE FILTER WARNING LIGHT RECORD NO. 4
PARTICLE FILTER WARNING LIGHT RECORD NO. 5
PARTICLE FILTER WARNING LIGHT RECORD NO. 6
PARTICLE FILTER WARNING LIGHT RECORD NO. 7
PARTICLE FILTER WARNING LIGHT RECORD NO. 8
PARTICLE FILTER WARNING LIGHT RECORD NO. 9
PARTICLE FILTER WARNING LIGHT RECORD NO. 10
PARAMETER
DEFINITIONThese parameters indicate the particle filter warning light record in miles (km).
NOTESSpecial note:
Check the interpretation of these parameters only on ALP21 Particle filter warning
light illuminated.
Vdiag 45 and 49 only.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
these parameters are used so that the history of the last ten illuminations of the particle filter warning light are
known.
Each parameter from PR836 to PR845 records the distance at which the particle filter warning light illuminated
and this is associated with the appearance of DF311 Number of regeneration failures exceeded.
The value is saved in the next parameter (PR+1) each time a new save is performed.
The distances of the last illumination of the particle filter warning light are saved in the other available parameters
(the distance information in PR836 is recopied to PR837 and the distance information in PR837 is recopied to
PR838 and so on).
When all ten parameters are not zero and the particle filter warning light illuminates again, the distance
information of PR836 Particle filter warning light record no. 1 is erased and replaced by the new value.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR836/SID304_V4D_PR837/SID304_V4D_PR838/SID304_V4D_PR839/SID304_V4D_PR840/SID304_V4D_PR841/
SID304_V4D_PR842/SID304_V4D_PR843/SID304_V4D_PR844/SID304_V4D_PR845/SID304_V49_PR836/SID304_V49_PR837/
SID304_V49_PR838/SID304_V49_PR839/SID304_V49_PR840/SID304_V49_PR841/SID304_V49_PR842/SID304_V49_PR843/
SID304_V49_PR844/SID304_V49_PR845/SID301_V4C_PR836/SID301_V4C_PR837/SID301_V4C_PR838/SID301_V4C_PR839/
SID301_V4C_PR840/SID301_V4C_PR841/SID301_V4C_PR842/SID301_V4C_PR843/SID301_V4C_PR844/SID301_V4C_PR845

13B-260
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
SC001
WRITE SAVED DATA
NOTESTo be able to run this command, it is essential to save the data using command SC003
Save computer data.
Writing is carried out after the computer has been reprogrammed or replaced.
Validating this command writes the data saved using command SC003 Save computer data.
The data is as follows:
– vehicle idle speed,
– programming of exhaust gas recirculation valve data,
– options available on the vehicle and managed by the computer (Example: Air conditioning),
– data specific to injection and particle filter operation.
The data configures the computer and prevents:
– engine malfunction after reprogramming or replacing the computer,
– incorrect interpretation of the information provided by the CLIP diagnostic tool.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_SC001 / SID304_V45_SC001 / SID301_V48_SC001 / SID304_V49_SC001 / SID304_V4D_SC001 / SID301_V4C_SC001

13B-261
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
SC003
SAVE COMPUTER DATA
NOTESThis save is carried out before computer reprogramming or replacement.
On the CLIP tool, select the SC003 Save computer data.
If the following message appears:
"a saved file exists, do you want to overwrite this data?":
(this file corresponds to the last save made on the CLIP diagnostic tool)
select "YES".
Confirming this command saves the following vehicle-specific data:
– the egr valve data programming;
– options available on the vehicle and managed by the computer (e.g. air conditioning);
– data specific to injection and particle filter operation.
This information will be saved in the CLIP diagnostic tool.
When saving is finished, run command SC001 Write saved data in order to configure the new computer after
programming or reprogramming.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_SC003 / SID304_V45_SC003 / SID301_V48_SC003 / SID304_V49_SC003 / SID304_V4D_SC003 / SID301_V4C_SC003