check engine RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Repair Manual

13B-118
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF1007
PRESENT
OR
STORED
CATALYTIC CONVERTER 1 DOWNSTREAM TEMPERATURE
SENSOR CIRCUIT
CC.0 : Short circuit to earth
CO.1 : Open circuit or short circuit to +12 V.
1. DEF: Micro-breaks
2. DEF: Signal outside lower limit
3. DEF: Signal inconsistency
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present:
– with the ignition on (for status CC.0),
– after a road test with a warm engine (for status CO. 1).
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– the level 1 warning light is lit,
– the OBD warning light illuminates after three consecutive driving cycles (starting + 5
seconds + switching off the ignition and waiting 1 minute).
IMPORTANT
The catalytic converter 1 downstream temperature sensor only measures
temperatures above 50°C.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and Kangoo II Wiring
diagrams Technical Note.
Run command AC029 High pressure circuit sealing test and check PR810 Catalytic converter 1
downstream temperature.
If the catalytic converter 1 downstream temperature is above 80°C, then the sensor is correct, otherwise continue
the fault finding procedure.
Check the connection and condition of the connector of the catalytic converter 1 downstream temperature
sensor, component code 1765.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the injection computer connector, component code 120 (see MR 392,
385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the catalytic converter 1 downstream temperature sensor, component code 1765
between connections 3AGX and 3AGY.
6886Ω 2565Ω 1192Ω 414Ω at 600°C,
277Ω If the resistance does not match these values, replace the catalytic converter 1 downstream temperature
sensor.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF1007 / SID304_V45_DF1007 / SID301_V48_DF1007 / SID304_V49_DF1007 / SID304_V4D_DF1007 / SID301_V4C_DF1007

13B-121
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF1009
PRESENT
OR
STOREDCATALYTIC CONVERTER 1 DOWNSTREAM TEMPERATURE
REGULATION
1. DEF: Signal outside lower limit
2. DEF: Signal outside upper limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present after a road test with particle filter regeneration.
Special notes:
If the fault is present:
The level 1 fault warning light is lit on the instrument panel.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and Kangoo II Wiring
diagrams Technical Note.
Check the connection and condition of the connector of the catalytic converter 1 downstream temperature
sensor, component code 1765.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the injection computer connector, component code 120 (see MR 392,
385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
With the ignition on, check the continuity, insulation and absence of interference resistance on the following
connections:
–3AGX between components 1765 and 120,
–3AGY between components 1765 and 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the turbine upstream temperature sensor.
While the engine is idling, check the return flow rate at the injectors.
After 5minutes the return volume must be between 16 mland 24 ml per injector.
If this tolerance is incorrect, replace the faulty injector(s).
Check the temperature of the catalytic converter; check that it is not too low.
Check that the exhaust system is not pierced.
Replace any faulty components.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF1009 / SID304_V45_DF1009 / SID301_V48_DF1009 / SID304_V49_DF1009 / SID304_V4D_DF1009 / SID301_V4C_DF1009

13B-123
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF1070
PRESENT
OR
STOREDCOLD LOOP
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present with the engine running and an air conditioning request.
Order of priority in the event of more than one fault:
Deal with fault DF049 Refrigerant sensor circuit first if it is present or stored.
Use the CLIO III, MODUS, MEGANE II ph2 and SCENIC II ph2 Wiring Diagrams
Technical Note.
When the fault is present or stored, the heating and air conditioning system is inhibited. There is no longer any air
conditioning.
Check the air conditioning fuse and check the air conditioning compressor connector, component code 171.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
– 38R between components 171 and 1337,
– Mbetween the earth and component 171.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Manually check if the compressor is jammed (turn the clutch plate manually to check that there is no point of
resistance).
In the event of jamming, replace the air conditioning compressor (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), Mechanical, 62A, Air conditioning, Compressor:
Removal - Refitting)
Charge the air conditioning circuit, check for any leaks and repair if necessary (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), Mechanical, 62A, Air conditioning, Air conditioning: Check
and air conditioning:
Draining - Filling).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF1070 / SID304_V45_DF1070 / SID301_V48_DF1070 / SID304_V49_DF1070 / SID304_V4D_DF1070 / SID301_V4C_DF1070

13B-127
MR-372-J84-13B050$585.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET001
COMPUTER + AFTER IGNITION FEED
STATUS DEFINITION"PRESENT": This status indicates that the + after ignition feed is active.
"ABSENT": This status indicates that the + after ignition feed is not active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2, CLIO III, MODUS and Kangoo II Wiring
Diagram Technical Note.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
"PRESENT"
NOTESIgnition on.
Normal operating condition.
Use a multimeter to check that there is no +12V with the ignition off on connectionAP15 or AP29 of
component120.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
"ABSENT"
NOTESIgnition on.
Check the supply fuse
–F18 (5A) (Kangoo II),
–313 (10A) (Modus and Clio),
–F5D (5A) (Mégane II and Scénic II),
of the main supply relay of the injection computer.
Use a multimeter to check for a + 12 V feed on the fuse holder with the ignition on.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET001/SID304_V45_ET001/SID301_V48_ET001/SID304_V49_ET001/SID304_V4D_ET001/SID301_V4C_ET001
MR-372-J84-13B050$585.mif
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2

13B-129
MR-372-J84-13B050$585.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of statuses
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
ET003
ENGINE IMMOBILISER
STATUS DEFINITION"ACTIVE": This status indicates that the immobiliser is active.
"INACTIVE": This status indicates that the immobiliser is not active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check: Engine switched off and ignition on or engine running, engine coolant temperature
>80°C
ACTIVE
NOTESIf status ET003 is permanently "ACTIVE", refer to the UCH
fault finding note (see 87B, Passenger compartment
connection unit).
INACTIVE
NOTESWith the ignition on and, when driving, status ET003 should
be "INACTIVE".
If it is not, refer to the UCH diagnostic note (see 87B,
Passenger compartment connection unit).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET003/SID304_V45_ET003/SID301_V48_ET003/SID304_V49_ET003/SID304_V4D_ET003/SID301_V4C_ET003

13B-130
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET004
AC AUTHORISED
STATUS DEFINITION"YES": This status shows that the air conditioning is authorised.
"NO": This status shows that the air conditioning is not authorised.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check: Engine switched off and ignition on or engine running, engine coolant temperature
>80°C
YES
The air conditioning authorisation only changes to "YES" if:
– the air conditioning request has been made by the driver (air conditioning switch in
AC position with minimum ventilation),
– the engine is not under full load,
– the air conditioning system is not faulty.
NOStatus ET004 remains at "NO" under the following conditions:
– Vehicle stopped with the ignition on,
– faults present in the air conditioning circuit,
– no air conditioning request made by the driver,
– engine under full load.
If status ET004 remains "NO" then the air conditioning should be authorised, check:
– that the air conditioning compressor is activated correctly,
– the air conditioning system feed fuses,
– the presence of refrigerant in the air conditioning circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET004/SID304_V45_ET004/SID301_V48_ET004/SID304_V49_ET004/SID304_V4D_ET004/SID301_V4C_ET004

13B-131
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET006
CODE PROGRAMMED
STATUS DEFINITION"YES": This status indicates that the immobiliser code has been programmed.
"NO": This status indicates that the immobiliser code has not been programmed.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
"YES"
Status ET006 is YES if dialogue is possible between the UCH computer and the
injection computer and the key code is recognised.
The engine is only authorised to start if the code is recognised by the UCH computer
and if status ET003: Immobiliser is INACTIVE.
In the event of a fault, see87B, passenger compartment connection unit,
conformity check.
"NO"Status ET341 is NO if dialogue is not possible between the UCH computer and the
injection computer (status ET003 Immobiliser remains ACTIVE).
This fault may be caused by incorrect key programming or a lack of key programming.
In this case, refer to the UCH fault finding note (see87B, Passenger compartment
connection unit) and follow the key programming procedure.
If the key programming is not the cause, run a multiplex network test (see88B,
multiplex) and check that dialogue between the UCH and the injection computer is
possible.
If dialogue is not established, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET006/SID304_V45_ET006/SID301_V48_ET006/SID304_V49_ET006/SID304_V4D_ET006/SID301_V4C_ET006

13B-132
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET021
HIGH-SPEED FAN REQUEST
STATUS DEFINITION"ACTIVE": The status indicates that the high-speed fan request is active.
"INACTIVE": The status indicates that the high-speed fan request is not active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
NOTE:
Status ET021 "High-speed fan request" changes status simultaneously.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
ACTIVE
The injection computer requests the activation of the high speed GMV when:
– the engine coolant temperature is above 104 °C.
– the injection computer has system faults that could lead to the engine
overheating.
When the high speed fan is supplied:
status ET021 High speed fan request becomes ACTIVE.
INACTIVEThe high-speed engine fan assembly stops when:
– the engine coolant temperature is below 102 °C;
– no fault which could cause engine overheating is present in the injection
system.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET021/SID304_V45_ET021/SID301_V48_ET021/SID304_V49_ET021/SID304_V4D_ET021/SID301_V4C_ET021

13B-133
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET022
LOW SPEED GMV CONTROL
STATUS DEFINITION"ACTIVE": The status indicates that the low-speed fan request is active.
"INACTIVE": The status indicates that the low-speed fan request is not active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
NOTE:
Status ET022 Low-speed fan request changes status.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
ACTIVE
The injection computer requests the activation of the low speed GMV when:
– the engine coolant temperature is above 96 °C.
– the injection computer has system faults that could lead to the engine
overheating,
– the air conditioning is switched on by the driver.
When the high speed fan is supplied:
status ET022 "Low speed fan request" becomes "ACTIVE"
INACTIVEThe low-speed engine fan assembly stops when:
– the engine coolant temperature is below 94 °C,
– no fault which could cause engine overheating is present in the injection
system.
– the air conditioning is not switched on by the driver.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET022/SID304_V45_ET022/SID301_V48_ET022/SID304_V49_ET022/SID304_V4D_ET022/SID301_V4C_ET022

13B-134
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET023
FAST IDLE SPEED REQUEST
STATUS DEFINITION"ACTIVE": This status indicates that the fast idle speed request is active.
"INACTIVE": This status indicates that the fast idle speed request is inactive.
NOTESSpecial notes:
The idle speed setpoint is dependent on:
– the coolant temperature,
– the emission control programs,
– air conditioning requirements,
– the electrical consumers,
– battery voltage.
– the gear engaged.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
ACTIVE
Status is "ACTIVE" when there is an engine load:
●inconsistency between the positions of the brake and accelerator pedals,
●coolant temperature <80 °C or >89 °C,
●heating and air conditioning system activated,
●with electrical consumers,
●the battery voltage is incorrect.
INACTIVEStatus is "INACTIVE" when there is no engine load:
●coolant temperature = 80 °C,
●heating and air conditioning system deactivated,
●without electrical consumers,
●the battery voltage is correct.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET023/SID304_V45_ET023/SID301_V48_ET023/SID304_V49_ET023/SID304_V4D_ET023/SID301_V4C_ET023