RENAULT TWINGO 2009 2.G Electrical Equipment Manual PDF
Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 241
Page 71 of 241
85A-1
WIPING - WASHING
Wiping and washing: List and location of components85A
I - LIST OF COMPONENTS II - POSITION OF THE COMPONENTS
1 - Windscreen wiper switch
To remove the windscreen wiper switch (see 84A,
Control - Signals, Screen wiper switch: Removal -
Refitting, page 84A-6) .
2 - UCH
The UCH is located in the dashboard, above the pas-
senger compartment relay/fuse box; to remove it (see
87B, Passenger compartment connection unit,
UCH: Removal - Refitting, page 87B-1) . No. Description
(1) Windscreen wiper switch
(2) UCH
(3) Passenger compartment fuse and relay
box
(4) Windscreen wiper blade
(5) Windscreen wiper blade arm
(6) Windscreen wiper mechanism
(7) Windscreen wiper motor
(8) Windscreen wiper jet
(9) Rear screen wiper blade
(10) Rear screen wiper blade arm
(11) Rear screen wiper motor
(12) Rear screen wiper jet
(13) Windscreen washer bottle
(14) Windscreen washer pump
(15) Rain and light sensor
121134
119507
Page 72 of 241
85A-2
WIPING - WASHING
Wiping and washing: List and location of components85A
3 - Passenger compartment fuse and relay box
4 - Windscreen wiper blade5 - Windscreen wiper blade arm
6 - Windscreen wiper mechanism
7 - Windscreen wiper motor
119504
119382
119382
119389
119389
Page 73 of 241
85A-3
WIPING - WASHING
Wiping and washing: List and location of components85A
8 - Windscreen wiper jet
9 - Rear screen wiper blade10 - Rear screen wiper blade arm
11 - Rear screen wiper motor
The rear screen wiper motor is located under the tail-
gate trim.
119382
119527
119520
119425
Page 74 of 241
85A-4
WIPING - WASHING
Wiping and washing: List and location of components85A
12 - Rear screen washer jet
13 - Windscreen washer bottle14 - Windscreen washer pump
15 - Rain and light sensor
The rain and light sensor is located under the interior
rear-view mirror covers.
119532
121090121089
101715
Page 75 of 241
85A-5
WIPING - WASHING
Windscreen wiper blade: Removal - Refitting
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
II - REMOVAL OPERATION FOR PART
CONCERNED
aPress on the windscreen wiper blade clip (1) .
aExtract the windscreen wiper blade from the winds-
creen wiper arm at (2) .
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit the windscreen wiper blade onto the winds-
creen wiper arm.
119383
Page 76 of 241
85A-6
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
LEFT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aVisually mark the position of the wiper arms (1) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the nut covers (2) .
aRemove nuts (3) .
aRemove the windscreen wiper arms (4) using the
(Ele. 1294-01) (5) . Special tooling required
Ele. 1294-01Tool for removing wiper arms.
Tightening torquesm
wiper arm nuts21 Nm
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119382
119385
119386
119387
Page 77 of 241
85A-7
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
LEFT-HAND DRIVE
85A
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aFit the windscreen wiper arms in the position marked
before the removal operation (1) .
aRefit the wiper arm nuts.
aTorque tighten the wiper arm nuts (21 Nm).
aRefit the wiper arm nut covers.
119382
Page 78 of 241
85A-8
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
RIGHT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aVisually mark the position of the wiper arms (1) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the nut covers (2) .
aRemove nuts (3) .
aRemove the windscreen wiper arms (4) using the
(Ele. 1294-01) (5) . Special tooling required
Ele. 1294-01Tool for removing wiper arms.
Tightening torquesm
wiper arm nuts21 Nm
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119382
125228
125229
125230
Page 79 of 241
85A-9
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
RIGHT-HAND DRIVE
85A
REFITTING
REFITTING OPERATION FOR PART CONCERNED
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aFit the windscreen wiper arms in the position marked
before the removal operation (1) .
aRefit the wiper arm nuts.
aTorque tighten the wiper arm nuts (21 Nm).
aRefit the wiper arm nut covers.WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119382
Page 80 of 241
85A-10
WIPING - WASHING
Windscreen wiper mechanism: Removal - Refitting
LEFT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the front windscreen wiper mechanism bolts (1) ,
-the windscreen wiper mechanism.
aDisconnect the windscreen wiper motor connector.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the windscreen wiper motor connector.
aRefit:
-the windscreen wiper mechanism,
-the windscreen wiper mechanism bolts.
II - FINAL OPERATION.
aRefit the scuttle panel grille (see Scuttle panel
grille: Removal - Refitting) (MR 412, 56A, Exterior
equipment).
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aRefit the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) . WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119389
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.