light RENAULT TWINGO 2009 2.G Mechanism And Accessories User Guide

55A-5
EXTERIOR PROTECTION
Front bumper: Stripping - Rebuilding
55A
aInsert rivets into the lower cover at (3) .
aClip on:
-the central absorber (2) ,
-the badge.
aRefit:
-the bolts (1) ,
-the electrical wiring (depending on equipment le-
vel),
-the front fog lights (depending on the equipment le-
vel) (see Front fog light: Removal - Refitting)
(MR 411, 80B, Headlights).
II - FINAL OPERATION.
aRefit the front bumper (see 55A, Exterior protec-
tion, Front bumper: Removal - Refitting, page
55A-1) .

55A-6
EXTERIOR PROTECTION
Front bumper: Stripping - Rebuilding
C44, and EQUIPMENT LEVEL SPORT
55A
STRIPPING
I - STRIPPING PREPARATION OPERATION
aRemove the front bumper (see 55A, Exterior pro-
tection, Front bumper: Removal - Refitting, page
55A-1) .
II - STRIPPING OPERATION FOR PART
CONCERNED
aRemove the front fog lights (see Front fog light:
Removal - Refitting) (80B, Headlights).
aRemove the bolts (1) .
aUnclip the badge.aUnclip the centre absorber (2) .
120886
132040

55A-8
EXTERIOR PROTECTION
Front bumper: Stripping - Rebuilding
C44, and EQUIPMENT LEVEL SPORT
55A
aCut the clips (7) .
aUnclip the aerodynamic component.
aUnclip the « front side extender - front extender - fog
light support » assembly (8) .aDetach the decorative strip (9) .
REBUILDING
I - REBUILDING PREPARATION OPERATION
aClean the bonding areas using a LINT-FREE
CLOTH soaked in HEPTANE (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) by pressing firmly and moving
slowly from back to front and in one direction only.
aWipe the bonding areas with a clean, dry LINT-
FREE CLOTH in one direction only.
132039
132037132036
Note:
Chec k for any stains on the clean and dry lint-
free cloth. If any traces of stains are found,
resume the cleaning procedure.

55A-9
EXTERIOR PROTECTION
Front bumper: Stripping - Rebuilding
C44, and EQUIPMENT LEVEL SPORT
55A
II - REBUILDING OPERATION FOR PART
CONCERNED
aPlace the decorative strip to be bonded on the front
bumper and centre it visually.
aStick the decorative strip down taking care to keep it
properly aligned.
aClip:
-the « front side extender - front extender - fog light
support » assembly,
-the aerodynamic component.
aDrill a hole at each clip position (7) using a ∅ 4.5 mm
drill bit.
aRivet the aerodynamic component.
aClip the lower grille and the radiator grille onto the
tabs provided using the clips (part no.: 77 03 076
037).
aRefit the diffuser.
aClip on the lower absorber (4) .
aRefit new rivets.
aClip:
-the central absorber (2) ,
-the badge.
aRefit the front fog lights (see Front fog light: Remo-
val - Refitting) (80B, Headlights).
III - FINAL OPERATION.
aRefit the front bumper (see 55A, Exterior protec-
tion, Front bumper: Removal - Refitting, page
55A-1) .

55A-10
EXTERIOR PROTECTION
Rear bumper: Removal - Refitting
55A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the rear lights (see Rear wing light: Re-
moval - Refitting) (81A, Rear lighting).
aUnclip the side extenders of the rear bumper (1)
using a flat-blade screwdriver.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolts (2) .
aRemove the bolts (3) . EQ UIPMENT LEVEL SPORT
132041
119260
119255

55A-11
EXTERIOR PROTECTION
Rear bumper: Removal - Refitting
55A
aRemove the bolts (4) .aRemove the bolts (6) .
aUnclip the rear bumper at (5) .
aRemove the rear bumper at (6) (this operation requi-
res two people).
aDisconnect the number plate light connector. EQUIPMENT LEVEL EA0 or EQUIPMENT LEVEL
EA1 or EQUIPMENT LEVEL EA3 or EQUIPMENT
LEVEL EA5 or EQUIPMENT LEVEL EAG or EQUI-
PMENT LEVEL EZ2 or EQUIPMENT LEVEL EZ4
119259
EQUIPMENT LEVEL SPORT
132043
119254

55A-12
EXTERIOR PROTECTION
Rear bumper: Removal - Refitting
55A
aDisconnect the proximity sensor connector.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the proximity sensor connector.
aConnect the number plate light connector.
aRefit the rear bumper (this operation requires two
people).
II - FINAL OPERATION
aClip on the side extenders of the rear bumper in or-
der (7) , (8) , (9) , (10) , (11) .
aRefit the rear lights (see Rear wing light: Removal
- Refitting) (81A, Rear lighting).aCarry out a function test on all functions.
REAR PROXIMITY RADAR
REAR PROXIMITY RADAR
EQ UIPMENT LEVEL SPORT
132043

55A-13
EXTERIOR PROTECTION
Rear bumper: Stripping - Rebuilding
55A
STRIPPING
I - STRIPPING PREPARATION OPERATION
aRemove the rear bumper (see 55A, Exterior pro-
tection, Rear bumper: Removal - Refitting, page
55A-10) .
II - STRIPPING OPERATION FOR PART
CONCERNED
aRemove the proximity radars (see Proximity radar:
Removal - Refitting) (87F, Parking distance con-
trol).
aRemove:
-the number plate lights (see Number plate light:
Removal - Refitting) (81A, Rear lighting),
-the electrical wiring.
aUnclip the outer impact strips.
REBUILDING
I - REBUILDING OPERATION FOR PART
CONCERNED
aClip on the outer impact strips.
aRefit:
-the electrical wiring,
-the number plate lights (see Number plate light:
Removal - Refitting) (81A, Rear lighting).
aRefit the proximity radars (see Proximity radar: Re-
moval - Refitting) (87F, Parking distance control).
II - FINAL OPERATION.
aRefit the rear bumper (see 55A, Exterior protec-
tion, Rear bumper: Removal - Refitting, page
55A-10) . REAR PROXIMITY RADAR
EQUIPMENT LEVEL EA0 or EQUIPMENT LEVEL
EA1 or EQUIPMENT LEVEL EA3 or EQUIPMENT
LEVEL EA5
120801
EQUIPMENT LEVEL EA0 or EQUIPMENT LEVEL
EA1 or EQUIPMENT LEVEL EA3 or EQUIPMENT
LEVEL EA5
REAR PROXIMITY RADAR

57A-1
INTERIOR EQUIPMENT
Dashboard: Removal - Refitting
57A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove the passenger front airbag (see Passen-
ger's frontal airbag: Removal - Refitting) (88C,
Airbags and pretensioners).
aRemove:
-the windscreen pillar trims (see Windscreen pillar
trim: Removal - Refitting) (71A, Body internal
trim),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and pre-
tensioners),
-the steering wheel (see Steering wheel: Removal
- Refitting) (36B, Power-assisted steering).aRemove the rev counter (depending on the equip-
ment level) (see Rev counter: Removal - Refitting)
(83A, Instrument panel).
aRemove:
-the steering column switch assembly (see Stee-
ring column switch assembly: Removal - Refit-
ting) (84A, Control - Signals),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),
-the tweeters (see Tweeter: Removal - Refitting)
(86A, Radio),
-the centre console (see 57A, Interior equipment,
Centre console: Removal - Refitting, page 57A-
12) ,
-the centre front panel (see 57A, Interior equip-
ment, Centre front panel: Removal - Refitting,
page 57A-7) ,
-the control panel (see Control panel: Removal -
Refitting) (61A, Heating).
aUnclip the dashboard side faces. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
FRONT SIDE AIRBAG
ENGINE REV COUNTER
121136

57A-9
INTERIOR EQUIPMENT
Glovebox: Removal - Refitting
57A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove the dashboard (see 57A, Interior equip-
ment, Dashboard: Removal - Refitting, page 57A-
1) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the pins (1) .
aRemove the glovebox.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the glovebox, Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121311
121310