catalytic converter RENAULT TWINGO RS 2009 2.G Engine And Peripherals Owner's Manual

12A-53
FUEL MIXTURE
Exhaust manifold: Removal - Refitting
D4F, and 780 or 782
12A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see ) (80A, Battery).
aRemove:
-the engine undertray,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the upstream oxygen sensor (see 17B, Petrol in-
jection, Oxygen sensors: Removal - Refitting,
page 17B-13) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the catalytic converter (see 19B, Exhaust, Cata-
lytic converter: Removal - Refitting, page 19B-
12) ,
-the turbocharger (see 12B, Turbocharging, Tur-
bocharger: Removal - Refitting, page 12B-4) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the exhaust manifold nuts (6) .
aRemove:
-the exhaust manifold by undoing the central stud
with a male torx socket and removing the manifold
with a large screwdriver as shown at (7) ,
-the exhaust manifold heat shield bolts,
-the exhaust manifold heat shield,
-the exhaust manifold gasket. Tightening torquesm
exhaust manifold heat
shield bolts18 N.m
exhaust manifold nuts
(initial torque)20 N.m
exhaust manifold nuts30 N.m
IMPORTANT
Wear cut-resistant gloves during the operation.
121200
121771

12A-54
FUEL MIXTURE
Exhaust manifold: Removal - Refitting
D4F, and 780 or 782
12A
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: exhaust manifold
seal.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the exhaust manifold heat shield,
-the exhaust manifold heat shield bolts.
aTorque tighten the exhaust manifold heat shield
bolts (18 N.m).
aRefit:
-a new exhaust manifold gasket,
-the exhaust manifold.
aRefit the exhaust manifold nuts.
aPretighten to torque the exhaust manifold nuts
(initial torque) (20 N.m).
aTorque tighten the exhaust manifold nuts (30
N.m).
III - FINAL OPERATION
aRefit:
-the turbocharger (see 12B, Turbocharging, Tur-
bocharger: Removal - Refitting, page 12B-4) ,
-the catalytic converter (see 19B, Exhaust, Cata-
lytic converter: Removal - Refitting, page 19B-
12) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the upstream oxygen sensor (see 17B, Petrol in-
jection, Oxygen sensors: Removal - Refitting,
page 17B-13) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the engine undertray.
aConnect the battery (see ) (80A, Battery).

12A-57
FUEL MIXTURE
Exhaust manifold: Removal - Refitting
K4M
12A
II - REMOVAL OPERATION
aRemove the exhaust manifold nuts.
aRemove:
-the bolts (5) from the « exhaust manifold - catalytic
converter » assembly,
-the « exhaust manifold - catalytic converter » as-
sembly,
-the seal from the « exhaust manifold - catalytic
converter » assembly.
132379
132392
132360

12A-58
FUEL MIXTURE
Exhaust manifold: Removal - Refitting
K4M
12A
If replacing the « exhaust manifold - catalytic
converter » assembly
aRemove:
-the upstream and downstream oxygen sensors (6)
,
-the heat shield (7) .
REFITTING
I - REMOVAL PREPARATION OPERATION
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease:
-the exhaust manifold joint face if it is to be re-used,
-the cylinder head joint face.
aparts always to be replaced: exhaust manifold
seal.
aTorque tighten the exhaust manifold studs (9
N.m).If replacing the « exhaust manifold - catalytic
converter » assembly
aClean the threading of the upstream and down-
stream oxygen sensors using a wire brush.
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease:
-the thread holes of the upstream and downstream
oxygen sensors on the exhaust manifold,
-the threading of the upstream and downstream ox-
ygen sensors.
aRefit the heat shield.
aTighten:
-to torque and in order the heat shield bolts (12
N.m),
-to torque the upstream and downstream oxygen
sensors ( 44 N.m).
aIf the strut mounting bolt on the cylinder block be-
comes loose, torque tighten the strut mounting
bolt on the cylinder block ( 75 N.m).
II - REFITTING OPERATION
aRefit:
-a new seal on the « exhaust manifold - catalytic
converter » assembly,
-the « exhaust manifold - catalytic converter » as-
sembly.
132441
Note:
If a stud loosens during removal, coat it with
HIGH RESISTANCE THREADLOCK (see Vehi-
cle: Parts and consumables for the repair)
(04B, Consumables - Products).
132441

12B-4
TURBOCHARGING
Turbocharger: Removal - Refitting
K9K
12B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see ) (80A, Battery).
aRemove:
-the engine cover,
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the EGR solenoid valve (see 14A, Antipollution,
Exhaust gas recirculation solenoid valve: Re-
moval - Refitting, page 14A-10) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the catalytic converter (see 19B, Exhaust, Cata-
lytic converter: Removal - Refitting, page 19B-
12) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aLoosen the clip (1) of the air outlet pipe on the air fil-
ter unit.
aDisconnect the oil vapour rebreathing pipe (2) .
aRemove:
-the air outlet pipe of the air filter unit (3) ,
-the turbocharger oil pipes (see 12B, Turbocharg-
ing, Turbocharger oil pipe: Removal - Refitting,
page 12B-12) . Equipment required
cleaning trough
par ts washer
compressed air nozzle
Tightening torquesm
studs on the turbo-
charger9 N.m
turbocharger nuts28 N.m
121633

12B-6
TURBOCHARGING
Turbocharger: Removal - Refitting
K9K
12B
aRemove:
-the turbocharger nuts (8) ,
-the turbocharger,
-the turbocharger seal.
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: seal between ex-
haust manifold and turbocharger.
aIf there has been a fault in the turbocharger, check
that the inlet circuit assembly is not full of oil. If it is,
remove the components to be cleaned, and clean
them using a cleaning trough or a parts washer
then dry them using a compressed air nozzle.
aIf the turbocharger is being reused, clean it using a
cleaning trough or a parts washer then dry it using
a compressed air nozzle.
aUse ABRASIVE PADS (see Vehicle: Parts and
consumables for the repair) (04B, Consumables -
Products) to clean the bearing faces:
-the exhaust manifold - turbocharger,
-the turbocharger - catalytic converter,
-the turbocharger - oil return pipe.aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) and clean cloths to degrease the
mating faces:
-of the exhaust manifold on the turbocharger side,
-of the turbocharger on the exhaust manifold side,
-of the turbocharger on the catalytic converter side,
-of the turbocharger on the oil return pipe side,
-of the catalytic converter on the turbocharger side.
aIn the event of replacement, torque tighten the
studs on the turbocharger (9 N.m).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the turbocharger fitted with a new seal.
aTorque tighten the turbocharger nuts (28 N.m).
aConnect:
-the turbocharging pressure regulator pipe,
-the intercooler air inlet pipe on the turbocharger
side.
aClip the intercooler air inlet pipe on the turbocharger
side.
aConnect the turbocharger air outlet pipe to the turbo-
charger.
aTighten the clip of the turbocharger air outlet pipe on
the turbocharger.
aRefit the turbocharger oil pipes (see 12B, Turbo-
charging, Turbocharger oil pipe: Removal - Re-
fitting, page 12B-12) .
aRefit the air outlet pipe onto the air filter unit.
112327
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).
K9K, and 718
K9K, and 740

12B-7
TURBOCHARGING
Turbocharger: Removal - Refitting
K9K
12B
III - FINAL OPERATION
aRefit:
-the catalytic converter (see 19B, Exhaust, Cata-
lytic converter: Removal - Refitting, page 19B-
12) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the EGR solenoid valve (see 14A, Antipollution,
Exhaust gas recirculation solenoid valve: Re-
moval - Refitting, page 14A-10) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the engine cover.
aConnect the battery (see ) (80A, Battery).

12B-8
TURBOCHARGING
Turbocharger: Removal - Refitting
D4F, and 780 or 782
12B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove the engine undertray.
aDrain the manual gearbox (see Manual gearbox
oils: Draining - Filling) (21A, Manual gearbox).
aRemove:
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the upstream oxygen sensor (see 17B, Petrol in-
jection, Oxygen sensors: Removal - Refitting,
page 17B-13) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front right-hand wheel driveshaft (see Front
right-hand driveshaft: Removal - Refitting)
(29A, Driveshafts),
-the catalytic converter (see 19B, Exhaust, Cata-
lytic converter: Removal - Refitting, page 19B-
12) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the turbocharger oil return pipe (see 12B,
Turbocharging, Turbocharger oil pipe: Removal
- Refitting, page 12B-12) .
aFit the tools (Ms. 583) onto the turbocharger cooling
hoses (6) .
aRemove the turbocharger cooling hose clips using
the tool (Mot. 1448).
aDisconnect the turbocharger cooling hoses.
aRemove the turbocharger cooling pipe strut bolt (7) .
aRemove the turbocharger oil supply pipe (see 12B,
Turbocharging, Turbocharger oil pipe: Removal
- Refitting, page 12B-12) . Special tooling required
Ms. 583Pipe clamps .
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
turbocharger nuts21 N.m
turbocharger cooling
pipe hollow bolts30 N.m
turbocharger cooling
pipe bracket bolts10 N.m
IMPORTANT
Wear cut-resistant gloves during the operation.121773

12B-11
TURBOCHARGING
Turbocharger: Removal - Refitting
D4F, and 780 or 782
12B
III - FINAL OPERATION
aRefit:
-the catalytic converter (see 19B, Exhaust, Cata-
lytic converter: Removal - Refitting, page 19B-
12) ,
-the front right-hand wheel driveshaft (see Front
right-hand driveshaft: Removal - Refitting)
(29A, Driveshafts),
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the upstream oxygen sensor (see 17B, Petrol in-
jection, Oxygen sensors: Removal - Refitting,
page 17B-13) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) .
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aRefill:
-and bleed the cooling system (see 19A, Cooling,
Cooling system: Draining - Refilling, page 19A-
9) ,
-the manual gearbox (see Manual gearbox oils:
Draining - Filling) (21A, Manual gearbox).
aRefit the engine undertray.

12B-13
TURBOCHARGING
Turbocharger oil pipe: Removal - Refitting
D4F, and 780 or 782
12B
a
aRemove the turbocharger air outlet pipe bolt (3) on
the throttle valve.
aUnclip the turbocharger air outlet pipe on the turbo-
charger in the direction of the arrow (4) .
aDisconnect the turbocharger air outlet pipe from theturbocharger.
aMove aside the turbocharger air outlet pipe.
aRemove the catalytic converter (see 19B, Exhaust,
Catalytic converter: Removal - Refitting, page
19B-12) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the lower bolts from the heat shield,
-the upper bolts from the heat shield,
-the heat shield.
1 - Oil supply pipe
aRemove:
-the bolt (6) from the turbocharger oil supply pipe on
the turbocharger,
-the bolt (7) on the turbocharger oil supply pipe on
the cylinder block,
-the turbocharger oil supply pipe bolt (8) ,
-the turbocharger oil supply pipe.
122834
122673
Note:
If the turbocharger air outlet pipe tightening clip
(1) is removed, the flexible rubber pipe (2) and
the tightening clip (1) must be replaced.
Note:
If the clip (5) is removed from the heat resistant
protector, the latter must be replaced.
120962