Seat Leon 5D 2010 MEDIA SYSTEM 2.2

Telephone control (Phone)
80The columns below the Bluetooth
® symbol show the strength of the current
signal (strength of signal from the main mobile phone station).
To display the above, the mobile phone should accept the handsfree profile
1.5 .
Function buttons in the PHONE main menu : dial.
: address book.
: missed calls.
6): numbers dialled.
: calls received.
: voice mailbox number
7).
: accept or make a call.
8): make emergency call.
Setup menu Telephone (SETUP)The functions activated with the button are required for the
connection of a mobile phone or an external Bluetooth device ⇒page 77.6)This may vary depending upon the country.7)The number of the voice mailbox should be entered manually in the telephone setup
menu ⇒ page 80.8)The SOS or emergency call function is not displayed on all appliances and is not avail-
able in all countries even through the mobile phone operator.AAABACADAEAFSOS
Bluetooth settings
Function button: Result
: enter the voice mailbox number.: the telephone book entries in the radio and navigation
system will be updated from the mobile phone and SIM card. The proce-
dure may last several minutes.: sets the volume of phone calls.: Restore factory settings in telephone menu and delete
user profiles and numbers stored.
Enter voice mailboxLoad address bookTe leph on e vol umeFactory settings
MediaSystem2.1_EN.book Seite 80 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)81
Stored numbersGuideAfter a connection with a mobile phone has been established, the entries in
the address book can be viewed and used via the PHONE telephone control.
Opening and scanning through the address book•In the PHONE main menu, press the function button to open the
address book.•Scroll through the address book using the setting knob ⇒page 8, fig. 1
.•Select the required entry on the screen or press the setting knob to call
the number.
If an address book entry has only one number, this number is called directly. If an address book entry has several phone numbers, the entry is shown with
the symbol
…. When this entry is selected on the screen or when the setting
knob is pressed, all the numbers stored for this entry are displayed.
Displaying the information for an address book entry
•In the Address book menu, press to display all the numbers saved
under this name.•Dial the number, by pressing it on the screen or by pressing the setting
knob.Note
Up to 2500 entries in the address book can be managed using the telephone
control (Phone).Searching for an entry in the address book•Open the address book.
Fig. 79 Address book.
]
A10
Details
Fig. 80 Searching for an
entry in the address book
MediaSystem2.1_EN.book Seite 81 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)
82•Press the function button.•Enter the name you are searching for in the input window.
Each time you enter a character, the sequence of characters in the input line
is automatically completed with a name that is in the address book.
If no name is offered when all the characters have been entered, there is no
entry in the address book corresponding to the sequence of characters you
have entered.•Delete characters in the line of data until a name is suggested.
Both upper and lower case are accepted when searching for an entry in the
address book.•Press the function button to select the entry in the address book
when you have found it.•Alternatively: press the right unit button to select the entry in the list,
when you have found it.•Press the selected address book entry to make a call.•Alternatively: press the setting knob ⇒page 8, fig. 1 to make the
call.Displaying and editing the phone numberA telephone number stored in the address book or in a call list can be
changed before you dial it.
Displaying and changing telephone numbers via an input window•Select the phone number and press the function button.•Press the function button to view the number in the input window.
The phone number can be changed here or reproduced as a DTMF sequence.
After you have changed the number, you can dial it by pressing the function
key . The changes
are not saved permanently in the address book. The modified
phone number can be viewed in the call list Numbers dialled after a call has
been made.
Call listsAll the call lists in the mobile phone memory can be consulted using the radio
and navigation system phone control system. The call lists give all the calls
made using the mobile phone.
If the phone accepts the handsfree profile 1.5 , calls not made through the
radio and navigation phone control system will also be shown.
Missed calls
The call list gives all missed and unanswered calls.
Numbers dialled
The call list gives all the phone numbers selected through the mobile phone
and through the radio and navigation phone control system.
SearchOK
A10
Details
Edit

Fig. 81 Call list.
MediaSystem2.1_EN.book Seite 82 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)83
Calls answered
The call list gives all the incoming calls answered with the mobile phone and
via the radio and navigation phone control system.
Opening the call list•Press the required call list function button in the PHONE main menu.•Alternatively: select the required call list in the PHONE main menu by
turning the setting knob ⇒page 8, fig. 1 and open by pressing the
button.
If a phone number has been saved in the address book, the call list will
display the name stored against the phone number instead of the number.Note
The call list display will depend on the mobile phone used.
A10
MediaSystem2.1_EN.book Seite 83 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)
84Using the telephoneAccepting, ending or rejecting a callWhen there is an incoming call, the phone number of the caller is displayed
on the radio and navigation screen.
If a phone number has been saved in the address book, the name stored
against the phone number is displayed instead of the number.
An incoming call can be accepted, ended or rejected using the radio and navi-
gation phone control system.•Press the function button to answer the call.•Press the function button to answer the call.•Press the function button to reject the call.Enter and call a phone number
It is possible to enter a phone number manually using the PHONE main menu.•Open the PHONE main menu by pressing the unit button.•In the PHONE main menu, press the function button ⇒page 79,
fig. 78.•Enter the required phone number in the input window by pressing the
characters.•After entering the complete phone number, press the function button
to make the call.Making a call from the address book•Open the address book in the PHONE main menu.•Select the required entry by turning the setting knob ⇒page 8, fig. 1 .•Press the setting knob to dial the number.•ALTERNATIVELY: Press the required entry to make the call.Making a call from the call list•Open the call list in the PHONE main menu.•Select the required entry in the list by turning the setting knob ⇒page 8,
fig. 1 .•Press the setting knob to dial the number.•ALTERNATIVELY: Press the required entry to make the call.•Alternatively: press the function button or the lower unit button to
make the call.
^^
Fig. 82 Enter a telephone
number.
PHONE
AA

A10
A10

MediaSystem2.1_EN.book Seite 84 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)85
During a phone callActive connection display
During a phone call, the number of the caller and the length of the conversa-
tion are displayed on the screen.
If the phone number has been saved in the address book, the name allocated
to the number is displayed instead of the number.
Muting the call
To prevent the caller listening to conversations inside the car during an active
connection, the sound transfer to the other phone can be temporarily discon-
nected.•Press the button with a connection established.•Press the function button in the pop-up window to disconnect
sound transmission to the other caller.•Press the function button again in the pop-up window to restore
sound transmission to the other caller.
Accepting and holding an additional callAn additional call may be accepted during a telephone conversation. It is
possible to switch between calls.
Call notification: Accept additional incoming call•If you receive another call while you are talking on the phone, the phone
number or name of the caller is displayed on the screen. The display “ ...
calling ” is also shown•To reject the second caller, press the function button .•ALTERNATIVELY: Press the left unit button.•To accept the second call, press directly on the call notification, or the
function button .•ALTERNATIVELY: Press the right unit button.
If you accept the second call, the first caller is put on hold, but the connection
is not cut off (display: “ Hold call”).
Fig. 83 Display an active
connection.
ExtrasMuteMute
Fig. 84 Call notification.^

MediaSystem2.1_EN.book Seite 85 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)
86Alternating: Alternating between two calls•To alternate between two calls, press the call display for the caller you
wish to talk to.•Alternatively: press the function button and, in the pop-up
window, the function button.
While one of the callers is connected, the other caller will be kept on hold.•To end an active connection with a caller, press the function button .•ALTERNATIVELY: Press the left unit button.
During an active conversation it is only possible to place one other caller on
hold at the same time.Note
The “Call notification” function must be activated on the mobile phone.
Note
The behaviour of the “Alternate” function will depend on the handsfree
profile version One requirement for the above functions is compatibility with
HFP 1.5 .
Making a conference callOne caller “on hold” can be included in the active conversation, to make a
conference call.
Adding several callers to a conference call
All the callers in the conference are able to hear and speak to the other
callers.•Press the function button and the function button in
the pop-up window to add both callers to the conference call.
Both callers are shown in line on the screen as “ Conference callers”.
An additional incoming call may be accepted during a telephone conference.
It is possible to alternate between the conference and the new call, or the new
caller can be invited to join the conference. Depending on the provider, the
conference call may include up to six callers.•Press the function button to end the conference call and separate the
connection with all the callers.
Extras
Alternate calls
^
Fig. 85 Adding several
callers to a teleconfer-
ence.
Extras
Conference
^
MediaSystem2.1_EN.book Seite 86 Donnerstag, 29. April 2010 4:18 16

Settings (SETUP)87
Settings (SETUP)Sound, volume and system settingsIntroductionPressing the unit button first opens a context-sensitive settings menu
for the currently selected mode.
Additional Information:•Safety notes
’ ⇒ page 6
•Unit overview ⇒ page 8•Radio settings menu ⇒ page 14•Media settings menu ⇒ page 29•Navigation settings menu ⇒ page 63•Phone settings menu ⇒ page 75
Sound and volume settings
SETUP
Fig. 86 Selection menu
for sound settings.Fig. 87 Settings menu for
treble level.
MediaSystem2.1_EN.book Seite 87 Donnerstag, 29. April 2010 4:18 16

Settings (SETUP)
88Opening the Sound main menu•Press the unit button from any menu.•Press the function button at the bottom-left of the screen to open
the menu for changing sound and volume settings ⇒page 87, fig. 86.
The currently selected settings are indicated in the overview by the scale in
the circle
“ next to the respective menu item ⇒page 87, fig. 86 .
Changing the balance and fader settings
•Press the function buttons , or to open the respective
settings menus for adjusting the “tone” ⇒page 87, fig. 87 .•Turn the setting knob ⇒page 8, fig. 1 or press the function button
or to alter the current setting.•Press the function button or to open the settings menu for
changing the sound focus to the left or right (balance) or to the front or rear
(fader).•Turn the setting knob or press the appropriate function button to alter the
current setting.
Changing the volume settings and adjustments
The volume settings and adjustments can be pre-defined.
While you adjust volume settings, the currently active audio source is played
at the level of the setting as you change it.•In the Sound main menu , press the function button ⇒ page 87,
fig. 86 .•Press the function button ,
⇒ page 23, or
to open the corresponding settings menu.•Turn the setting knob or press the or function button.•Pressing the function button opens a pop-up window in
which you can set the automatic audio volume reduction applied when the
parking distance warning system is active. Functional description of speed-dependent volume adjustment (GALA)
The speed dependent volume adjustment automatically increases the
volume as the vehicle speed increases.
The degree to which the volume increases with speed is adjusted on a scale
between
1 and 7.
If a low value is set, the volume rises only slightly as the speed of the vehicle
increases. At a high setting the volume is increased more. At 0 speed-
dependent volume control is switched off (display: Off).
System settings•Press the unit button and the function button to open the
settings menu.
Resetting to factory settings
The restoration of the original settings deletes all the previous entries, desti-
nations and other settings .•In the System settings menu , press the function button.•Confirm the prompt by pressing to reset the unit to its original
settings.
Other system settings
SETUPSound
Treble
Mid
Bass
A10

€
Balance
FaderVol u m e
Max. switch-on volume
Traffic announcements (TP)
Navigation volume
Speed-dependent vol. adjustment

€
vol. reduction
Function button: Result
: Press to select the desired language for text and voice output.
ALTERNATIVELY: select to use the language programmed on
the instrument panel.
: The keyboard in input windows has an alphabetic layout.
SETUP
SystemFactory settings
Ye s
Language
Automatic
View of keyboardABC
MediaSystem2.1_EN.book Seite 88 Donnerstag, 29. April 2010 4:18 16

Settings (SETUP)89
Note
The system of units used in the navigation menu (metric or imperial) is set on
the instrument panel.
: The keyboard in input windows has the usual computer layout.: Change display settings.
: press to select the screen brightness setting.: changes the map view.: the map view changes when the dipped beams are
switched on.
: the map view remains in daytime mode (bright).: the map view remains in night-time mode (dark).
: Switch the confirmation tone for pressing a function
button on or off.
: restore the unit to its original factory settings.
, , Changes to the air conditioning are displayed on the
screen for approximately 3, 5 or 10 seconds.: Changes to the air conditioning settings are not displayed on the
screen.
: switch time display on or off ⇒page 11.
Function button: ResultQWERTYScreenBrightnessDay/NightAutomaticDayNightAcoustic feedbackFactory settingsAir conditioning announcements3s
5s
10 s
OffTime display
MediaSystem2.1_EN.book Seite 89 Donnerstag, 29. April 2010 4:18 16