SSANGYONG KORANDO 1997 Service Repair Manual

SSANGYONG MY2002
9R-6 BODY FRONT END
HOOD HINGES
Removal and Installation Procedure
1. Remove the hood. Refer to “Hood” in this section.
2. Remove the cowl vent grille. Refer to “Cowl Vent
Grille” in this section.
3. Remove the side cowl vent panel Refer to “Side
Cowl Vent Panel” in this section.
4. Remove the bolts and the hood hinges
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
5. Installation should follow the removal procedure
in the reverse order.
KAA9R040
HOOD GAS SPRING
Removal and Installation Procedure
1. Open the hood.
2. Remove the wiper arms. Refer to Section 9D,
Wipers/Washer System.
3. Remove the cowl vent grille with the screws.
4. Remove gas spring fix bolt and pull up the gas
spring from the ball stud by spreding the retainer
with screw driver.
5. Remove ball stud from hood. (or not)
Installation Notice
6. Installation should follow the removal procedure
in the reverse order.
KAA9R050
Tightening Torque12.74 - 25.48 Nm
(9.4 - 18.8 lb-ft)
Tightening
Torque9 - 11 Nm
(6.63 - 8.11 lb-ft)
16 - 23 Nm
(11.8 - 16.96 lb-ft)
Spring fix
bolt
Ball stud
bolt

BODY FRONT END 9R-7
SSANGYONG MY2002
11.8 - 16.96
5.78 - 8.68
9.40 - 18.8
6.63 - 8.11 16 - 23
7.84 - 11.76
12.74 - 25.48
9 - 11
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Ball Stud Bolt
Hood Hinges Bolts
Hood to Bolts of the Hinges Bolts
Spring Fix BoltApplication N•m
Lb-FtLb-In
-
-
-
-

SECTION 9S
BODY REAR END
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless
otherwise noted.
TABLE OF CONTENTS
Description and Operation...................................9S-2
Fuel Filler Door.....................................................9S-2
Components Locator............................................9S-3
Lighting System..................................................9S-3
Repair Instructions................................................9S-4On-Vehicle Service Unit Repair................................9S-4
Fuel Filler Door.....................................................9S-4
Fuel Filler Door Remote Handle and Cable............9S-4
Specifications.......................................................9S-5
Fastener Tightening Specifications.......................9S-5

SSANGYONG MY2002
9S-2 BODY REAR END
DESCRIPTION AND OPERATION
FUEL FILLER DOOR
The fuel filler door attaches to the fuel tank pocket of
the left side of the vehicle. The door is opened by
pulling on the fuel filler door remote handle located on
the floor in front of the driver’s seat.

BODY REAR END 9S-3
SSANGYONG MY2002
COMPONENTS LOCATOR
LIGHTING SYSTEM
KAA9S010
1 PNL & HE A-F/Filler DR
2 Catch & Cable-F/Filler DR
3 BRKT-F/Filler DR O/Slam4 HDL A-F/Filler DR Release
5 Band
6 Screw-Hex SEMS

SSANGYONG MY2002
9S-4 BODY REAR END
ON-VEHICLE SERVICE
UNIT REPAIR
FUEL FILLER DOOR
Removal and Installation Procedure
1. Remove the bolts and the fuel filler door.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
2. Installation should follow the removal procedure
in the reverse order.
REPAIR INSTRUCTIONS
KAA9S020
KAA9S030
FUEL FILLER DOOR REMOTE
HANDLE AND CABLE
Removal and Installation Procedure
1. Remove the front seat. Refer to Section 9H, Seats.
2. Remove the front floor insulator.
3. Remove the screw with the fuel filler door remote
handle.
4. Remove the quarter trim panel. Refer to Section
9G, Interior Trim.
5. Disconnect the fuel filler door cable.
6. Installation should follow the removal procedure
in the reverse order.
Tightening Torque3.92 - 5.49 Nm
(2.92 - 4.08 lb-ft)

BODY REAR END 9S-5
SSANGYONG MY2002
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Fuel Filler Door BoltsApplication
N•m3.92 - 5.492.92 - 4.08 34.71 - 48.60Lb-FtLb-In

SECTION 9T1
REMOTE KEYLESS ENTRY AND ANTI-THEFT
SYSTEM
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless
otherwise noted.
TABLE OF CONTENTS
Description and Operation.................................9T1-2
Remote Keyless Entry and Anti-Theft System.....9T1-2
Components Locator..........................................9T1-3
REKES & STICS................................................9T1-3
Diagnostic Information and Procedure.............9T1-4
Input Memory....................................................9T1-5
Repair Instructions..............................................9T1-6
On-Vehicle Service Unit Repair..............................9T1-6Receiver............................................................9T1-6
Antenna.............................................................9T1-6
Stics..................................................................9T1-6
Schematic and Routing Diagrams.....................9T1-7
STICS - Stics Unit..............................................9T1-7
STICS - Door Contact Switch..............................9T1-8
STICS - Keyless, Key Reminder Switch, Siren,
Chime Bell Buzzer ..........................................9T1-9

SSANGYONG MY2002
9T1-2 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
DESCRIPTION AND OPERATION
REMOTE KEYLESS ENTRY AND
ANTI-THEFT SYSTEM
The remote keyless entry and anti-theft system can
perform the following functions:
•Remotely lock and unlock the vehicle doors by
means of a hand-held, high-frequency transmitter.
Sense intrusion into the vehicle through the doors
or the hood.
Activate a warning if an intrusion is detected.
Automatically relock the doors if thedoor or the
tail gate is not opened within 30 seconds after the
vehicle has been unlocked by remote keyless
entry.
Help the driver find the vehicle in a parking area.
The remote keyless entry system consist of the
following components:
STICS.
Remote keyless entry system receiver.
Hand-held transmitter.
Tailgate open switch.
Door contact switch.
Siren.
Hood open switch
Key reminder switch.
Antenna.
STICS can perform the following functions:
1. Wiper INT sening vehicle speed.
By operating INT tiem control volume, variable
time will be changed within 1.5-20 seconds
2. Washer relating wiper.

3. Dimming room lamp.
When room lamp is coupled with door, it truns on
if door is opened. After closing the door it
maintains 2 seconds of lighting and dims off
whithin 3 seconds.
4. Time delayed power window control.
Power window can be operated within 30 seconds
after truning the IGN 1 switch from ON to OFF. If
driver/passenger’s door is opened within the 30
seconds from that moment.
5. Rear defogger timer.
The rear defogger will be operated for 12 min. by
turning ON the defogger switch while engine is
running.
Defogger will be stopped by pushing the switch
again.
The defogger will be operated 6 mim, if push ON
the switch within 10 min. after 12 min. of operation.6. Seat belt waring.
The warning lamp will be turned on for about 6
sec. With an intermittent chime bell when the IGN.
Switch is ON unless fastening the seat belt.
7. parking brake warning.
The indicator lamp will flash if drive while the
parking brake is applied.
8. Tail lamp lighting warning.
When the driver’s door is opened while the tail
lamp is still ON, the buzzer operates intermittently.
In this condition, the door will be automatically
unlock when it locked.
9. Door ajar warning.
The indicator lamp will be blinking when the door
is not closed completely and driving.
10. IGN key reminder.
The chime will be operated intermittently if the
driver’s door is opened while the IGN key is still
remain-ing in the ignition switch. In this condition,
the door will be automatically unlocked when it
locked.
11. Central door lock.
All doors will be locked/unlocked by locking/
unlocking the driver’s or passenger’s door.
12. coupled with REKES.
Being coupled with REKES (remote keyless entry
system), all doors will be locked/unlocked
according to signals of transmitter when the
ignition key is not inserted.
13. iginition key hole illumination.
coupled with door switch, ignition key hole
illumination lamp will trun on when the driver ’s
door is opened and will dim off after 10 sec. After
closing the door.
14. Auto door lock.
All doors will be locked automatically if the vehicle
speed reaches 50 km/h though the doors are in
unlock.
15. Auto door unlock.
All doors will be automatically unlock if the vehicle
crashes while driving (over 15km/h).
Operate the burglar alarm.
1. Burglar alarm must operate immediately when the
door, tailgate or hood is opened with improper
ways after all doors and hood were closed and
continued this status for 1 seconds.
2. If the tailgate is opened by key when the system
is on the burglar alarm cindition, the sysem must
be changed to the second burglar alarm condition
frim normal condition.

REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM 9T1-3
SSANGYONG MY2002
COMPONENTS LOCATOR
REKES & STICS
KAA9T010
1. Remote Keyless Entry System Receiver
2. Antenna3. STICS