key SSANGYONG KORANDO 1997 Service Owner's Manual

1B3 -- 78 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
Installation Procedure
1. Install the hub.
Notice
Exactly align the woodruff key and the groove of hub
(arrow).
2. Install the washer (7) and tighten the bolt (6).
Washer (new) :1 EA200 N∙m (148 lb-ft) + 90_
3. Install the vibration damper.
Notice
Exactly align and insert onto the straight pin.
4. Install the belt pulley.
Tightening Torque25 N∙m (18 lb-ft)
Notice
Align the alignment marks.

1B3 -- 80 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
CRANKSHAFT FRONT RADIAL SEAL
1 Radial Seal
2 Timing Case Cover3 Woodruff Key
Tools Required
601589031400 Sleeve

OM600 ENGINE MECHANICAL 1B3 -- 81
D AEW OO M Y_2000
Notice
The sealing lip of the repair radial seal is offset to the
inside by 2mm to ensure that is does not run in any
groove which the standard radial seal may have left
on the crankshaft flange.
A Standard Radial Seal
B Repair Radial Seal
Replacement Procedure
1. Pull out the radial seal (1) and be careful not to dam-
age the sealing surface of timing case cover.
2. Thoroughly clean the mounting bore of the radial
seal.
3. Coat a little oil on the sealing lip of new radial (1) and
contact surface.
Notice
Don’t use grease.
4. Install the radial seal (1) by using a sleeve (4).
Notice
Align the groove of sleeve and woodruff key(arrow).
Sleeve 601 589 03 14 00

1B3 -- 158 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
CRANKSHAFT SPROCKET
Preceding Work : Removal of oil pan
Removal of timing case cover
1 12-- Sided Stretch Bolt (M11)
Check, 25N∙m (18 lb-ft)+90_ ...............
2 Washer
3 Camshaft Sprocket
4 Timing Chain
5 Bearing Pin
6 Bearing Pin
7OilPump
8 Oil Pump Sprocket
9 Oil Pump Chain10 Washer
11 Bolt 25N∙m (18 lb-ft) ......................
12 Crankshaft Sprocket
13 Crankshaft
15 Key
16 Guide Rail
17 Spring
18 Bushing
19 Tensioning Lever

1B3 -- 160 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
5. Place alignment marks (arrow) on the timing chain
(4) and crankshaft sprocket (12).
6. Remove the woodruff key(15).
7. Place alignment marks (arrow) on the timing chain
(4) and camshaft sprocket (3).
8. Remove the chain tensioner.
9. Remove the bolt (1) and then remove the washer (2)
and camshaft sprocket (3).
10. Remove the crankshaft sprocket (12) by using a
puller (20).
Puller 102 589 05 33 00

OM600 ENGINE MECHANICAL 1B3 -- 161
D AEW OO M Y_2000
Installation Procedure
1. Put the same alignment mark on the new crankshaft
sprocket as in the old sprocket.
Notice
Check the timing chain, camshaft sprocket, injection
pump timing sprocket, oil pump chain and oil pump
sprocket for wear and replace if necessary.
2. Install the new crankshaft sprocket (12) by using a
drift (21).
Notice
Align the groove of sprocket and woodruff key (ar-
row) exactly.
Drift 116 589 07 15 00
3. Fit the timing chain (4) on the crankshaft sprocket
(12).
Notice
Align the alignment marks (arrow) on the chain and
sprocket.
4. Install the camshaft sprocket (3).
Tightening Torque25 N∙m (18 lb-ft) + 90_
Notice
Pay attention on the alignment marks and dowel pin
(arrow).

1B3 -- 162 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
Notice
If the max. length ’L’ of the stretch bolt exceeds
53.6mm, replace it.
5. Fit the oil pump chain (9) on the crankshaft sprocket
(12) and insert the oil pump sprocket (8) into the oil
pump chain and then install it on the oil pump.
Notice
The curved side of the oil pump sprocket should
face the oil pump.
6. Insert the woodruff key (15).
7. Install the guide rail (16). Attach the spring (17) to
guide rail and to tensioning lever together onto the
bearing pins (5,6).
Notice
Ensure that the spring is correctly located in the
guide rail (arrow).

OM600 ENGINE CONTROLS 1F3 -- 5
D AEW OO M Y_2000
VACUUM CONTROLSYSTEM TEST
1 Ventilation (To Passenger Compartment)
2 Engine Cut -- Off Valve (Ignition Key Switch)
3 Auto-- locking Hub Solenoid Valve
4 Engine Stop Valve Unit
5 PLA Vacuum Unit (Idle Speed Adjustment)6Engine
7 Vacuum Pump
830_Thermovalve
9 Fuel Injection Pump
Test Data
Idle Speed IncreaseAt least 100 rpm at approx. 500mbr
Permissible Pressure Drop of System400 -- 500mbar approx. 1 min.

5A-48 AUTOMATIC TRANSMISSION
SSANGYONG MY2002
TROUBLE CODE DIAGNOSIS - GASOLINE VEHICLE
TCM DIAGNOSTIC SYSTEM
OVERVIEW
Notice: To prevent Transmission Control Module (TCM)
damage. The ignition key must be OFF when
disconnection or reconnection the power to the TCM
(for example bttery cable, TCM pigtail connector, TCM
fuse, jumper cables, etc.).
When the TCM detects a system fault, a Diagnostic
Trouble Code (DTC) is set in the TCM. This code is
present while the fault conditions are met and is stored
as a ‘History DTC’ until cleared. Condition for setting
and clearing each TCM DTC are provided in the relevant
sections.
In the case where the vehicle type is certified for Eure
On-Board Diagnostic (EOBD) compliance, the Engine
Control Module (ECM) provides the communication linkto the EOBD scan tool to pass on any EOBD relevant
codes from the TCM. The table below contains a list of
all supported DTCs and the classification of each for
EOBD purposes. Where a type B DTC has been set in
an EOBD vehicle, the response to the fault may include
action by the ECM, including the illumination of the
Malfunction lndicator Lamp (MIL). Refer to Section 1F,
Engine Control, for details on EOBD system function,
checks and fault clearing.
CLEARING TROUBLE CODES
TCM DTCs should be cleared after repairs have been
completed. Some diagnostic tables will tell you to clear
the codes before using the chart, which will help to
find the cause of the problem more quickly. Always
note the DTCs present before clearing - this information
may be helpful in the diagnostic process.”
DIAGNOSTIC TROUBLE CODES
DTC
P0706
P0707
P0708
P0710
P0790
P1703
P1704
P1708
P1709
P1712
P1713
P1714
P1715
P1717
P1718
P1719
P1720
P1721
P1722
P1733
P1734
P1735
P1736
P1737Type
B
B
B
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D Description
Transmission Range Sensor Circuit Range/Performance
Transmission Range Sensor Circuit Low input
Transmission Range Sensor Circuit High input
Transmission Fluid Temperature Sensor Circuit Malfunction
Normal/Performance Switch Circuit Malfunction
Engine Speed Signal Error
Shaft Speed Signal Error
TCM Supply Voltage Low
TCM Supply Voltage High
Kickdown Switch Circuit Malfunction
Pedal Signal Error
EEPROM Vehicle Code Error
VPS Offset Error
RAM Error
ROM Error
CAN Bus Error
EEPROM Error
Throttle Signal Error
Vehicle Type Determination Error
Solenoid 1 Circuit Open
Solenoid 2 Circuit Open
Solenoid 3 Circuit Open
Solenoid 4 Circuit Open
Solenoid 5 Circuit Open

5A-50 AUTOMATIC TRANSMISSION
SSANGYONG MY2002
Transmission Range Sensor Circuit Low Input
Transmission Range Sensor Circuit High Input
Transmission Fluid Temperature Sensor Circuit Malfunction
Normal/Performance Switch Circuit Malfunction
Engine Speed Signal Error
Shaft Speed Signal Error
TCM Supply Voltage Low
TCM Supply Voltage High
Air Conditioning Switch Circuit Malfunction
Kickdown Switch Circuit Malfunction
EEPROM Vehicle Code Error
VPS Offset Error
Throttle Not Learnt Error
RAM Error
ROM Error
EEPROM Error
Throttle Signal Error
Vehicle Type Determination Error
Solenoid 1 Circuit Open
Solenoid 2 Circuit Open
Solenoid 3 Circuit Open
Solenoid 4 Circuit Open
Solenoid 5 Circuit Open
Solenoid 6 Circuit Open
Solenoid 7 Circuit Open
Solenoid 1 Circuit Short
Solenoid 2 Circuit Short
Solenoid 3 Circuit Short
Solenoid 4 Circuit Short
TROUBLE CODE DIAGNOSIS - DIESEL VEHICLE
TCM DIAGNOSTIC SYSTEM
OVERVIEW
Notice: To prevent Transmission Control Module (TCM)
damage. The ignition key must be OFF when
disconnection or reconnection the power to the TCM
(for example bttery cable, TCM pigtail connector, TCM
fuse, jumper cables, etc.).
When the TCM detects a system fault, a Diagnostic
Trouble Code (DTC) is set in the TCM. This code is
present while the fault conditions are met and is storedas a ‘History DTC’ until cleared. Condition for setting
and clearing each TCM DTC are provided in the relevant
sections.CLEARING TROUBLE CODES
TCM DTCs should be cleared after repairs have been
completed. Some diagnostic tables will tell you to clear
the codes before using the chart, which will help to
find the cause of the problem more quickly. Always
note the DTCs present before clearing - this information
may be helpful in the diagnostic process.
DIAGNOSTIC TROUBLE CODES
DTC
P0707
P0708
P0710
P0790
P1703
P1704
P1708
P1709
P1710
P1712
P1714
P1715
P1716
P1717
P1718
P1720
P1721
P1722
P1733
P1734
P1735
P1736
P1737
P1738
P1739
P1741
P1742
P1743
P1744Description