display SSANGYONG KORANDO 2012 User Guide

05-58010-01
Previous Current
Ambient temperature also displayed on vehicle with manual A/C control switch
Both SVC and STD class
Previous Current
Warning lamp symbols fulfil ISO standards used on all models
(e.g. 4WD CHECK indicator symbol)
4) Warning lamps according to ISO standards
5) Ambient temperature display
SVC class
This is displayed for 2 seconds when activating winter mode, displayed for 2 seconds when deactivating
winter mode and displayed for 4 seconds when starting engine and driving off (DOT LCD message).
AutomaticAutomatic
Manual
SVC classSVC class
STD class

05-6
SVC class
Previous Current
Changed from figure type to bar graph type.
6) Average fuel economy reset and calibrated automatically when
refilling
7) Instant fuel consumption display changed
8) Pre-warning indicator for engine overheat removed
Both SVC and STD class
Previous Current
Reset by user Reset by user and automatic reset when refilling
9) TDMS logic changed
SVC class
Current
TDMS (Tier Direction Management System) is not displayed when EPS warning lamp comes on.
SVC class STD class
Pre-warning indicator for engine overheat is removed.
EPS warning lampTDMS displayLCD not displayed
EPS warning lamp
comes onLCD screen is not
displayed.

05-12
Low fuel level warning lamp â–¶
Warning lamp
(amber)
Engine overheat warning lamp â–¶
Warning lamp
(red)
Door ajar â–¶
Warning lamp
(red)
Seat belt reminder â–¶
Warning lamp
(red)
Air bag â–¶
Warning lamp
(red)
This lamp comes on if the fuel level is approx. 10 â„“ or below.
However, the fuel level may change slight depending on vehicle
condition, inclination of the road, etc. Also, it blinks if there is a short or
open circuit between the fuel level sensor and cluster.
<007e008f008c00950047009b008f008c0047008a00960096009300880095009b0047009b008c00940097008c00990088009b009c0099008c00470090009a0047005800590057020b006a0047009600990047008f0090008e008f008c009900530047009b00
8f0090009a0047009300880094009700470089009300900095>ks at an
interval of 1 second, a message is displayed, the warning sounds once
through the speaker and the buzzer sounds at an interval of 0.5 seconds.
This lamp comes on when any door is open or not closed completely.
(both STD and SVC class)
This lamp comes on when the ignition switch is pressed ON.
It keeps coming on if the driver's seat belt is not fastened.
This lamp comes on when the ignition switch is pressed to the ON mode.
Then, it goes off if the system is normal.
If this lamp stays on while driving, it means that the air bag system is faulty.

05-178010-01
Indicator
(amber)
Winter mode indicator(DSL only) â–¶
Steering wheel heating indicator â–¶
Indicator
(green)This indicator comes on when the winter mode switch is switched on and
goes off when the switch is off.
This comes on together with the winter mode display on the LCD screen.
(applies to STD class)
This indicator comes on when the steering wheel heating switch
is operated with the ignition switch turned on and the engine running.
(applies to SVC class)

05-24
4) Display Sequence
Display sequence for STD main LCD & SVC DOT LCD â–¶
Operating time of Trip
switchFunction
Below 1 second
(60 to 980 ms)STD Mode change
(ODO → TRIP A → TRIP B → DTE → AFC → IFC →
ILLUMINATION → OUT TEMP)
SVC Mode change
(TRIP A → TRIP B → DTE → AFC → IFC →
ILLUMINATION → OUT TEMP)
Over 1 seconds Reset function (Trip A, B, AFC)
<004f007000930093009c0094009000950088009b0090009600950047004f005d0047009b00960047005800470093008c009d008c0093005000530047009c00950090009b00470096008d00470096009c009b009a0090008b008c0047009b008c0094009700
8c00990088009b009c0099008c0047004f0b45004702e90047>℉))
Over 3 seconds - Ready Mode change
(Illumination → OUT TEMP → ODO)
If the Trip/Reset switch is not pressed within 3 seconds after getting into the illumination mode and the
ambient air temperature mode, the LCD changes to next mode.
The factory-setting mode is DTE (Distance To Empty) mode. *
*

05-258010-01
Operations for power supply in SVC â–¶
When the ignition switch is turned to ON position, the message "WELCOME" is displayed for 2
seconds on the DOT LCD and the seat belt reminder comes on for 4 seconds. However, if a signal
with higher priority is received, the seat belt reminder comes on only for 2 seconds to display it.
The pre-warning (system check) indicator comes on for 4 seconds and goes off 0.4 seconds after
that the ignition is switched on.
All input signals can be input 4 seconds after the pre-warning (system check) indicator starts
illuminating.
Only the symbol and DOT LCD are illuminated initially, if the SKM (Smart Key Module) or door (B-
CAN) signal is received
while B+ power is supplied.
If the ignition is switched on with the LCD illuminated, the DOT LCD and the symbol follow
the side fascia panel.
When the step 1, 2 and 3 are performed after 4 seconds, the seat belt warning lamp is deactivated in
advance.
Dial light ON condition: Lights up gradually for 2 seconds when the ignition is switched on. 1.
2.
3.
4.
5.
6.
5) Illumination & Brightness
(1) Operations for Power Supply

05-26
When the ignition is switched off, the message "GOOD-BYE" is displayed for 2 seconds and disappears.
The other LCDs go off as soon as the ignition is switched off.
The dial and pointer dim down for 2 seconds and go off at the same time when the DOT LCD goes off. 7.

05-278010-01
Operations for power supply in STD â–¶
The operation input before the LCD backlight is illuminated, right after the ignition is turned OFF or ON,
is ignored.
<007b008f008c00470073006a006b004700890088008a009200930090008e008f009b004700880095008b00470096009b008f008c009900470093008800940097009a004700880099008c0047009000930093009c0094009000950088009b008c008b004700
570055005b004700b70057005500580047009a008c008a0096>nd after the ignition ON is
detected.
The LCD display, LCD backlight, dial lamp and indicator lamp are turned on or off by the ignition
switch ON/OFF operation. -
-
-

05-378010-01
Function Signal Remark
Input data Speed signal
Display type 4 digits LCD
Display range A: 0.0 ~ 999.9 km
(mile)
B: 0.0 ~ 9999.9 km
(mile)
Resolution 0.1 km (mile)
Maximum Odo
valueA: 0.0 → 999.9 → 0.0
km
B: 0.0 → 9999.9 →
0.0 km
IGN OFF Memorize and maintain previous trip distance
Data clear Supply B+ voltage for the first time
Press and hold mode switch for more than 1 sec.
Maximum Odo
valueIf the signal indicating actual vehicle speed above 300 km/h is received, the data is
not accumulated.
Function Signal Remark
Input data Speed signal
Display type 6 digits LCD
Display range 0~999999 km(mile)
Hold
Resolution 1 km (mile)
Maximum Odo
valueIf the signal indicating
actual vehicle speed
above 300 km/h is
received, the data is
not accumulated.
STD Class Odometer Display & Data Storage â–¶
STD Class Tripmeter Display â–¶

05-38
Function Signal Remark
Display type 3 digits LCD
Display range 50 km ~ 999 km
(30 miles ~ 999 miles)
Resolution 1 km (mile)
Display interval every 1 seconds
(1) DTE (Distance To Empty) Mode
The DTE (distance to empty) function is an estimation on how much further the vehicle can be driven with
the fuel remaining in the tank, based on the previous driving pattern (fuel economy).
8) Display Mode
STD Class Odometer Display & Data Storage â–¶