battery SSANGYONG KORANDO 2012 Repair Manual

03-54
Disarming 3.
If the door unlock signal is received from the smart key remote control with power OFF or the
outside door handle switch signal is received with the driver door locked, the doors are unlocked,
turn signal lamps blink once, exterior buzzer sounds twice at the intervals with 50 ms ON/450 ms
OFF and theft deterrent mode is deactivated. When receiving the door unlock signal with the theft
deterrent mode disarmed, the turn signal lamps blink and exterior buzzer sounds.
When tailgate is open by tailgate open switch signal (only tailgate disarmed)
When verified smart key is detected and manual tailgate is open by tailgate open switch signal
(only tailgate disarmed)
When ignition switch is turned to ON position -
-
-
-
In theft deterrent mode
BCM observes the conditions below continuously: 4.
Battery connection (B+)
Front/rear door open
Tailgate open
4 doors lock/unlock
Engine hood open -
-
-
-
-
Activation of theft deterrent alarm 5.
When any of doors, tailgate or engine hood is open in theft deterrent mode
When unlocking the door lock switch in theft deterrent mode
When opening a door after completion of theft deterrent alarm (for 30 seconds)
Horn and the turn signal lamps operate for 30 seconds with the interval of 0.5s ON/0.5s OFF. -
-
-
-
Warning cancellation requirements 6.
The theft deterrent alarm is deactivated by the following BCAN signals during its operation: (theft
deterrent mode maintains) -
When door is unlocked by smart key remote control
When door is locked by smart key remote control
When tailgate is open by smart key remote control
When passive door is unlocked due to smart key detection
When tailgate is open due to smart key detection
When panic alarm is activated by smart key remote control 1)
2)
3)
4)
5)
6)
When turning the ignition switch to ON position during the theft deterrent alarm, the alarm stops
immediately.
When turning the ignition switch to ON position during the theft deterrent alarm, the alarm stops and
the theft deterrent mode is deactivated after 30 seconds (remaining time).
If there is not any disarming commend, the alarm stays ON for 30 seconds and the theft deterrent
mode continues. -
-
-

03-598710-01
Hazard flasher switch control ▶
When pressing the hazard flasher switch, the left/right turn signal lamps blink with the intervals of 400 ms
ON/400 ms OFF for 75/min and the interior buzzer sounds with same interval.
When pressing the hazard flasher switch again during its operation, the turn signal lamps and horn stop
the operation.
This function is available if the battery is connected (B+).
If the turn signal lamp is defective during its operation, the left turn signal lamp blinks with the interval of
300 ms ON/300 ms OFF (100/min) and the interior buzzer sounds with same interval.
The tolerance between left turn signal lamp and right turn signal lamp should be below 100 ms.
The hazard flasher has a priority over the turn signal lamp.
Priority of hazard flasher is as follows:
Seat belt reminder > Key reminder > Sunroof > Tail lamp > Hazard flasher > Turn signal lamp 1.
2.
3.
4.
5.
6.
7.

03-60
Hazard flasher indicator control ▶
When pressing the hazard flasher switch, the hazard flasher indicator blinks with the interval of
75/min.
When pressing the hazard flasher again switch during Step (1), the indicator stops its operation.
This function is available if the battery is connected (B+). 1.
2.
3.
Auto hazard flasher control ▶
When the auto hazard flasher is operated for 0.1~0.59 seconds, the hazard flasher indicator blinks 3
times.
When the auto hazard flasher is operated for more than 0.6 seconds, the hazard flasher indicator
blinks 10 times.
The hazard flasher has priority over the auto hazard flasher and both have the same flash frequency.
This function is only available when the ignition key is in the "ON" position.
When the ignition switch is turned to OFF position during its operation, the auto hazard flasher stops
the operation.
The hazard flasher stops operation as soon as the signal is received from the turn signal lamp (hazard
flasher) switch during this operation.
If the turn signal lamp switch is turned on, the auto hazard flasher does not operate even though its
signal is received. 1.
2.
3.
4.
5.
6.
7.

03-658710-01
22) Outside Mirror Folding/Unfolding Control
Folding/unfolding control ▶
When pressing the mirror folding/unfolding switch with IGN ON, the mirrors are folded or unfolded
according to the mirror condition. If the outside rearview mirror was folded, the mirror should be
<009c0095008d00960093008b008c008b0053004700880095008b0047009d0090008a008c0047009d008c0099009a008800550047006d00960093008b00900095008e0056009c0095008d00960093008b00900095008e00470096009c009b0097009c009b00
470090009a00470088008a009b0090009d0088009b008c008b> for 16±6 seconds.
This operation time should be completed even when the ignition switch is turned to OFF position
during its operation.
At first time pressing the mirror folding/unfolding switch after reconnecting the battery, the mirror
folding operation is performed.
You can control the mirror position within the first 30 sec. after turning the ignition OFF. In other
words, this control must be available for 30 seconds (time lag period) after turning the ignition switch
to OFF position. Folding/unfolding is completed when time lag of 30 seconds elapse during
operation.
When receiving the folding/unfolding signal during the mirror folding/unfolding operation, the output
should be activated after having time lag of 0.1 second.
The folding/unfolding operation is performed regardless of the vehicle speed.
Manual operation
<005400470074009000990099009600990047009c0095008d00960093008b008c008b004702e700470074009000990099009600990047008d00960093008b00900095008e0056009c0095008d00960093008b00900095008e0047009a0090008e0095008800
930047008d0099009600940047009a009e0090009b008a008f> → Mirror folding
<005400470074009000990099009600990047008d00960093008b008c008b004702e700470074009000990099009600990047008d00960093008b00900095008e0056009c0095008d00960093008b00900095008e0047009a0090008e009500880093004700
8d0099009600940047009a009e0090009b008a008f004702e7> Mirror unfolding 1.
2.
3.
4.
5.

03-698710-01
3) Operation of Immobilizer
When the ignition switch is turned to the ON position with REKES key, the BCM checks the crypto code
of the inserted key using the immobilizer antenna and sends whether the engine is startable or not to the
engine ECU through the CAN communication so that the engine can be started.
BCM
REKES key
Immobilizer antenna
ECUCAN line
For the vehicle with the immobilizer, there can be a problem in starting the vehicle or the system error:
When two or more immobilizer keys come into contact with (each) other(s).
When the key is close to any device sending or receiving electromagnetic fields or waves other
than Ssangyong products.
When the key is close to any electronic or electric devices such as lighting equipment, security keys
or security cards.
When the key is close to a magnetic or metal object or a battery. -
-
-
-

03-70
4) Components of REKES Key
Battery cover
Side & main cover Battery: CR2032TransponderKey plate Remote control PCB
How to replace battery ▶
Remove the battery cover using a flat screwdriver to replace the battery.
How to replace transponder ▶
Remove battery cover and battery
Remove rubber cover and screw then remove key plate
Remove side cover and main cover
Replace transponder -
-
-
-
Do not drop or shock to the transponder in the key as it may be damaged.
With a damaged transponder, the engine cannot be started.
When you erase the code or register an extra key, please attend on the site.
In any cases, the immobilizer system can not be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove, damage
or modify it.
The remote engine starter cannot be installed to the vehicle equipped with the immobilizer system. -
-
-
-
-

04-218712-03
(2) Ignition status change
The ignition status is changed to OFF, ACC ON, IGN ON and engine cranking by one START/STOP
button.
The SKM cuts the power for IGN2 and ACC relays while the engine is cranking as cutting the electric
load is necessary.
The SKM monitors the brake pedal status through the hardware signals.
The ignition status change is available when the engine START/STOP button is pressed.
The SKM uses the EMS (engine condition) and ABS/ESP (FR vehicle speed) signals sent through the
P-CAN bus (High Speed CAN).
When the smart key battery is discharged and the driver inserts the smart key into the immobilizer slot
in emergency mode, the smart key verification is performed if the brake or START switch is pressed
before the ignition status is changed (ACC ON, IGN ON).
Ignition status change during driving 1.
2.
3.
4.
5.
6.
7.
When the engine START/STOP switch is pressed for 3 sec. or more at more than 3 km/h, the
ignition status is changed from IGN to ACC.
If the engine START/STOP switch is pressed again, the ignition status is changed from ACC to
IGN.
The 4 vehicle speeds are abnormal (CAN signal timeout, abnormal signal):
If the engine START/STOP switch is pressed for 3 sec., the ignition status is changed from IGN
to ACC. If the switch is pressed again, the ignition status is changed from ACC to OFF (DTC
set). -
-
The SKM changes the ignition status as follows: 8.

04-298712-03
(4) Smart key battery discharge warning (3) Smart key verification fail warning
When the verification is requested for ignition status change or engine starting and no verified smart key
is in the vehicle, the SKM sends the [smart key verification status] signal, which indicates that the
verification has failed, for up to 10 sec. until the verification fail conditions are deactivated.
Verification fail detection and transmission conditions ▶
When the ignition status is changed after a smart key is verified by the START switch ON input, the
SKM sends the verification status for 10 sec. -Normally, the smart key verification warning is one of the smart key fail conditions. -
Ignition status change
(OFF ->ACC) / (OFF ->IGN)/(ACC ->IGN) / (IGN -> engine ON) *
If above conditions are met again, the SKM re-verifies a smart key and sends the verification status for
another 10 sec.
When the ignition status is changed by the transponder verification while the smart key status is sent
through the BCAN, the SKM sends the smart key verification signal and also sends the transponder
verification signal for 10 sec. -
-
If low smart key battery is detected during the verification process for ignition status change or engine
start, the SKM sends the signal for [smart key battery low voltage warning] to the BCM and instrument
cluster through the BCAN for up to 10 sec. until the warning condition is deactivated.
Smart key battery discharge confirmation and deactivation ▶
If the smart key battery low voltage is confirmed, the SKM sends the smart key battery low voltage
warning signal.
If the smart key battery is in normal condition, the SKM sends the smart key battery low voltage
warning deactivation signal.
The smart key is the last used key. -
-
*
(5) Transponder verification fail warning
If a verified smart key is not found by the key verification process, the SKM sends the information that
indicates the key is not verified to the instrument cluster through the BCAN for up to 10 sec. until the
verification fail condition is deactivated.
The SKM sends the transponder verification warning when the verification has failed with the smart key
inserted into the immobilizer holder. -
Transponder verification fail detection and transmission conditions ▶
When the ignition status is changed after the transponder is verified by the START switch ON input,
the SKM sends the transponder verification status for 10 sec. -

04-318712-03
(8) Brake not working alert
The SKM sends the brake not working alert signal for 10 sec. every time the ignition status is changed
after the 1st cycle (OFF-ACC-IGN-ACC-OFF) while the brake is not operated.
when the brake pedal is depressed, the system is reset and alert deactivation signal is sent.
when the 10 min. timer is terminated -
-
(9) Clutch not working alert
The SKM sends the clutch not working alert signal for 10 sec. every time the ignition status is changed
after the 1st cycle (OFF-ACC-IGN-ACC-OFF)
while the clutch is not operated.
when the clutch pedal is depressed, the system is reset and alert deactivation signal is sent.
when the 10 min. timer is terminated -
-
(10) Smart key slot detection alert
The SKM sends the smart key slot detection alert signal for 10 sec. when a smart key inserted into
the slot is detected with IGN OFF and the driver's door open. -
(11) SKM alert priority
1 Smart key out alert EXTERIOR
1
2 Smart key reminder alert EXTERIOR
3 Smart key verification fail alert INTERIOR
2 4 Transponder verification failure alarm INTERIOR
5 Smart key battery low voltage alert INTERIOR
6 Transmission position alert INTERIOR
7 SKM error alert INTERIOR
8 Brake alert INTERIOR
9 Clutch alert INTERIOR
10 Smart key slot reminder alert INTERIOR1
Warning cancellation requirements ▶
Warning cancellation requirements ▶
Warning transmission conditions ▶
Warning cancellation requirements ▶
when the smart key is removed, the alert deactivation signal is sent.
when the 10 min. timer is terminated -
-

05-138010-01
Indicator
(amber)
ESP ▶
ESP OFF indicator ▶
Engine check warning lamp ▶
Indicator
(amber)
Indicator
(amber)
Indicator (red)
Battery charge warning lamp ▶
Indicator (red)
Engine oil level warning lamp ▶This lamp comes on if any sensor or device related to the engine control is
defective.
This lamp comes on when the start switch is ON or when the battery level is
low.
(For EEM, warning lamp is controlled according to CAN signal)
This lamp comes on when the ignition switch is turned to "ON" position,
and then goes off if the engine oil level is normal.
If the engine oil level warning lamp comes on while driving, check the
engine oil level and oil leakage. -
- This indicator comes on when the ESP system is faulty.
This indicator comes on when pressing the ESP OFF switch.