SSANGYONG KORANDO 2012 Service Manual

05-28
Brightness in SVC ▶
(2) Illumination Level
Brightness in STD ▶
Operating power Illumination levelMain LCD Dial pointer
Day Night Day Night
B+
(B-CAN Wake UP)- OFF OFF OFF OFF
IGN1Level 1 100% 20% 100% 20%
Level 2 100% 30% 100% 30%
Level 3 100% 40% 100% 40%
Level 4 100% 50% 100% 50%
Level 5 100% 60% 100% 60%
Level 6 100% 70% 100% 70%
Operating powerIllumination
previousDOT LCD ODO, GAGE LCDDial
pointer
Day Night Day Night Day Night
B+
(B-CAN
Wake
UP)After
-Level 6 Level 6OFF (however, level 6 for initial
operation with B+ & IGN1 ON)
After
1st timeMaintains
previous
levelMaintains
previous
levelOFF (however, maintains previous level
for initial operation with B+ & IGN1 ON)
IGN1Level 1 25% 5% 25% 5% 25% 5%
Level 2 40% 12% 40% 12% 40% 12%
Level 3 55% 19% 55% 19% 55% 19%
Level 4 70% 26% 70% 26% 70% 26%
Level 5 85% 33% 85% 33% 85% 33%
Level 6 100% 40% 100% 40% 100% 40%

05-298010-01
(1) SVC
Symbols in SVC ▶
6) System Analysis

05-30
Symbols in SVC (via CAN) ▶

05-318010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch to
ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

05-32
(2) STD
Symbols in STD ▶

05-338010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch
to ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

05-34
Symbols in STD (via CAN) ▶

05-358010-01

05-36
7) Odometer (ODO) and Trip Meter (TRIP)
The total driving distance (0 to 999,999 km or 0 to 999,999 miles) and the trip distance (0.0 to 999.9 km
or 0.0 to 9,999.9 miles) are calculated by using the value of pulse per 1 km which is programmed in the
EEPROM.
Applicable maximum driving speed is 300 km/h. If the vehicle speed goes over the limit, ODO and Trip
meter does not operate any more and the pointer indicates the maximum km/h (MPH). The pulse count
information is sent from the speed module according to the speed CAN data that matches the speed
frequency.

05-378010-01
Function Signal Remark
Input data Speed signal
Display type 4 digits LCD
Display range A: 0.0 ~ 999.9 km
(mile)
B: 0.0 ~ 9999.9 km
(mile)
Resolution 0.1 km (mile)
Maximum Odo
valueA: 0.0 → 999.9 → 0.0
km
B: 0.0 → 9999.9 →
0.0 km
IGN OFF Memorize and maintain previous trip distance
Data clear Supply B+ voltage for the first time
Press and hold mode switch for more than 1 sec.
Maximum Odo
valueIf the signal indicating actual vehicle speed above 300 km/h is received, the data is
not accumulated.
Function Signal Remark
Input data Speed signal
Display type 6 digits LCD
Display range 0~999999 km(mile)
Hold
Resolution 1 km (mile)
Maximum Odo
valueIf the signal indicating
actual vehicle speed
above 300 km/h is
received, the data is
not accumulated.
STD Class Odometer Display & Data Storage ▶
STD Class Tripmeter Display ▶