SSANGYONG KORANDO 2012 Service Manual

09-98790-00
While reversing, if obstacles are within stage 1, the warning beep sounds with long intervals. If within
stage 2, the warning beep sounds with short intervals and if within stage 3, the warning beep sounds
continuously.
Sensor detection range
Within 20 cm from the ground
(Objects may not be detected in this range.)
Buzzer interval when measuring distance ▶
2) Rear PAS Sensor

09-10
Circuit diagram of ECU ▶
Internal circuit diagram of sensors ▶

09-118790-00
Sensor operating sequence ▶
The ultrasonic sensors transmit ultrasonic waves
and receive the reflected waves from an obstacle
to detect it in the following order: L → C → R.

09-12
4. OUTPUT SPECIFICATIONS FOR SENSOR SELF-
DIAGNOSIS BUZZER SOUND
Fail condition (However, no obstacle should be within 30 cm)
1. The signal wire is open
2. The power wire (+ and -)is open -Conditions to "FAIL" in sensor diagnosis ▶Buzzer interval during self diagnosis ▶
Timeout processing time for buzzer interval after measuring distance/self diagnosis: 600 ms
- If timeout is reached, the PAS returns to undetected condition.
Process while re-inputting
- After timeout, the process is performed normally if the signal required for display is received
from beginning to end. (not detectable if the signal is received in the midst of process) 1.
2.Exception/error handling ▶ Self diagnosis is performed once when the ignition is switched on (gear shift lever in "R" position). If the
system is defective (Fail) due to open sensor or communication problem, the information for the failed
sensor is displayed as buzzer sound.
If it is normal, the warning buzzer sounds for 60 ms.

10-38910-05
1. SPECIFICATION
Unit Description Specification
General Rated voltage DC 14 V (Negative ground)
Speaker 4 Ohm
Output 45 W x 4 channels
Current consumption 10 A (at maximum power)
MP3[WMA], CD Sampling frequency 8 times oversampling
DA converter 4 DAC system
Pick-up type Astigma 3-beam
Light source Semiconductor laser
Wave length 780nm
Frequency response20Hz ~ 20kHz(± 3dB)
Signal to noise ratio≥50 dB
Total harmonic distortion≤1% (1kHz)
Wow and flutter Below measurable limits
Channel separation≥35dB
Radio Frequency range FM
MW
LW87.5MHz ~ 108MHz
522kHz ~ 1,620kHz
144kHz ~ 290kHz
Usable sensitivity FM
MW
LW≤18 dBu
≤35 dBu
≤35 dBu
Signal to noise ratio FM
MW
LW≥45dB
≥40dB
≥40dB
Stereo separation FM≥20dB
Bluetooth Performance Audio distribute profile (A2DP)

10-4
Unit Description Specification
USB MP3[WMA] Frequency response 20Hz ~ 20kHz
Total harmonic distortion 0.1 % (at 1kHz)
Dynamic Range 85dB (at 1kHz)
Signal-to-noise ratio 60dB (at 1kHz)
Channel separation 54dB (at 1kHz)
Micro-pole antenna Operating current up to 150 mA
Operating voltage DC 10.5 ~ 16.0 V
Operating temperature-30˚C ~ +60˚C
Storage temperature-40˚C ~ +80˚C
Input/output impedance75Ω (FM)

10-58910-05
Audio assembly
CDP (MP3) + Bluetooth CDP(MP3) + RDS + Bluetooth
<007b008f008c004702c8006a00680073007302c900470089009c009b009b009600950047008d00960099004700690093009c008c009b00960096009b008f0047009a00a0009a009b008c00940047008f0088009a00470089008c008c009500470088008b00
8b008c008b0055>
2. MAJOR CHANGES
RDS (Radio Data System) is a broadcasting service which a growing number of FM stations are now
providing. It allows the FM stations to send additional signals along with their regular programme signals.
For example, the stations send their station names and information about what type of programme they
broadcast, such as sports or music, etc.
When tuned to an FM station which provides the RDS service, the RDS indicator lights up, the station
frequency (and then the station name if sent) is displayed.
Not all FM stations provide RDS service, nor do all RDS stations provide same services. If in doubt,
check with local radio stations for details on RDS services in your area.
This machine can use the following RDS service.
PS (Programme Service name) / PTY (Programme Type) / TP (Traffic Program) / TA (Traffic
Announcement) / AF (List of Alternative Frequencies) / RT (Radio Text)
This allows you to locate a specific type name of programme being broadcast.
3. RDS (RADIO DATA SYSTEM) AUDIO

10-6
Front door speaker
Remote control switch on steering
wheel
1. LAYOUT
Audio
CDP (MP3)
Radio
USB/AUX
Bluetooth hands-free -
-
-
-
-
Front door tweeter speaker

10-78910-05
Hands-free microphoneRear door speaker
USB/AUX
Audio assembly
CDP (MP3) + Bluetooth CDP(MP3) + RDS + Bluetooth

10-8
1) Audio Control Switch
No. Name
1 Power/Mute/Pause/Enter/Volume button
2 Station memory button (1~6) and Audio function button
3 Bluetooth hands-free CALL button
4 Bluetooth hands-free END button
5 Previous (≪) and Next (≫) button
6 SCAN/INFO button
7 BAND/AS button
8 SETTING button
9 Display window (LCD)
10 USB/AUX button
11 Disc Play button
12 Disc Eject button
13 Disc slot
CDP (MP3) + Bluetooth ▶