belt SSANGYONG MUSSO 1998 Workshop Manual PDF

SECTION 8A
SEAT BELTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 8A-1
Fastener Tightening Specifications . . . . . . . . . 8A-1
Component Locator . . . . . . . . . . . . . . . . . . . 8A-2
Front Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . 8A-2
Rear Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . 8A-3
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
General Description and System
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 8A-4
Driver Seat Belt Warning . . . . . . . . . . . . . . . . 8A-4
Operation and Functional Checks . . . . . . . . . 8A-4
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Anchor BoltNlm
35 - 55

8A-2 SEAT BELT
COMPONENT LOCATOR
FRONT SEAT BELT
1 Seat Belt Assembly (3-Point)
2 Buckle Assembly
3 Seat Belt Dust Cover
4 Seat Belt Webbing Guide5 Seat Belt Reel Assembly
6 Anchor Bolt..........................................35-55 Nm
7 Anchor Bolt..........................................35-55 Nm
8 Anchor Bolt..........................................35-55 Nm

SEAT BELTS 8A-3
REAR SEAT BELT
1 Seat Belt Assembly (3-point)
2 Seat Belt Stalk Plate Assembly
3 Seat Belt Assembly (2-Point)
4 Webbing Buckle Assembly (Center)5 Webbing Buckle Assembly (Rear)
6 Webbing Hanger
7 Seat Belt Dust Cover
8 Webbing Guide

8A-4 SEAT BELT
GENERAL DESCRIPTION
AND SYSTEM OPERATION
DRIVER SEAT BELT WARNING
The driver's safety belt incorporates a safety belt reminder
light in the instment cluster remind the driver if the safety belt
is not fastened when the ignition is turnd ON.
OPERATION AND FUNCTIONAL
CHECKS
Caution:
lKeep sharp objects and potentially damaging objects
away from the seat belts.
lAvoid bending or damaging any portion of the buckle
or the latch plate.
lDo not bleach or dye the belt webbing. Use only mild
soap and water in order to clean the belts.
lWhen installing the seat belt anchor bolts and the
screws, start the bolts and screws by hand in order
to prevent crossthreading.
lDo not attempt any repairs on the retractor
mechsemblies with new assemblies.
lReplace any belts that are cut r damaged in any way.
1. Inspect all saet belt anchor bolts and the screw in order to
verify that they are secure.
2. Inspect the seat belt buckle. The buckle must lock and
unlock easily.
3. After inserting the latch into the buckle, tug sharply on the
belt. The buckle must remain locked.
4. Fully extend the shoulder belt portion to make sure that
there is no twisting or tears in the belt.
5. Let the shoulder belt retract fully. The belt should retract
easily.

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-3
CAUTIONS
Failure to follow the correct service procedure can cause air bag damage or personal injury due to unexpected air
bag deployment. Before service (removal and installation of part, check for replacement), please be weal noticed of
following items for your correct service.
1. For service, turn the ignition switch to ‘LOCK’ position and wait for 30 seconds after disconnecting the negative
battery cable.
2. If the vehicle collapsed, remove the air bag ECU first to reserve the crash records.
3, Never use other vehicles’ air bag components and replace with specified new part.
4. Never disassemble or repair the air bag module, air bag unit and wiring harness to re-use.
5. Replace the air bag module and air bag unit with new if it dropped, cracked or damaged.
6. Only qualified technicians in service shop should check or repair the air bag,
7. Before service, should be well noticed of warning labels on the vehicle.
A. Sun Visor Side
[Warning]
Pull down the sun visor and see SRS air bag
warning lamp on the head lining.
B. Head Lining
[Warning]
1 . This vehicle is equipped with air bag. Air bag is
supplemental device for the seatbelt. Fasten
your seatbelt.
2. This air bag should be replaced by authorized
supplier within replacement intervals.
3. When the ignition key is turned to ON position,
SRS warning lamp will turn on for 6 sec. and go
off. In this case, the system is normal.
For the following cases, see service manual.
- SRS warning lamp does not turn on.
- SRS warning lamp does not go off.
- SRS warning lamp continues to blink.
C. Steering Wheel Body Inner
[Warning]
Before removing the steering wheel, read service
manual first. Set the front wheels straight forward
and align the center position marks of SRS clock
spring. Improper removal or installation of the
steering wheel can damage the SRS components.D. Engine Compartment
[Warning]
This vehicle is equipped with air bag. Before
checking the engine compartment, read service
manual first. Faultuy check and service can cause
SRS air bag deployment and system defects that
can be led to severe damage.
E. Battery Cable
[Warning]
Before disconnecting the battery power, read
service manual first.

8B-22 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
GENERAL DESCRIPTION
AND SYSTEM OPERATION
INTRODUCTION
SRS (Supplemental Restraint System) air bag protects driver
and passenger by inflating air bag under collision and seat
belt pre - tensioner is a supplemental equipment for seat belt
reducing shocks from the collision by pulling passenger’s body
against seat back at the same time of air bag inflation.
Air bag unit has diagnosis functions and indicates system
malfunctions to the driver by turning on the air bag warning
lamp.
CAUTION
Perform the service procedures for the air bag system as
ordered, if not, the air bag can be operated suddenly and it
could result in damage of air bag or injury. Before service
(removal, installation, checking and replacement of parts),
observe the following instructions and service correctly.
1. To service, turn the ignition switch to ‘LOCK’ position and
disconnect the negative battery cable and continue the
procedures after approx. 30 seconds.
2. If the vehicle is damaged due to accident, remove the air
bag ECU first to get the accident records.
3. Never use the other vehicle’s air bag parts and replace
with genuine part, if required.
4. Do not disassemble or repair the air bag module, air bag
unit and wiring harness to reuse.
5. Replace the air bag unit or air bag module if dropped,
cracked or damaged.

BODY WIRING SYSTEM 9A-9
44 Joint Connector.................................................... Ground
45 Door Unlock Switch
46 Front Fog Lamp Switch
47 Rear Defogger Switch
4 8 ECS Switch
49 Rear Fog Lamp Switch........................................Rear Fog Lamp
50 Digital Clock
51 Thermo Amplifier
52 Glove Box Lamp Switch
53 Air Conditioner Wiring Connetor
54 Glove Box Lamp
55 Ground 6
56 Ground 6.............................................................Gasoline E/G
57 Ground 7.............................................................Gasoline E/G
58 Wheel Speed Sensor (FR)..................................ABS 5.0 or ABD 5.0
59 O
2 Sensor............................................................E32 Gasoline E/G
60 Engine Main Wiring Connector............................Gasoline E/G with MSE ECU
61 HFM .....................................................................Gasoline E/G with HFM ECU
61-1 MSE .....................................................................Gasoline E/G with MSE ECU
62 Front Door Wiring Connector (Passenger Side)
63 Front door Wiring Connector (Passenger Side)
64 Joint Connector (B+)
65 Audio
66 Audio
67 Air Bag Wiring Connector
68 Chime Bell
6 9 Buzzer
70 Kick Down Switch.................................................Automatic Transmission
71 Diode 2................................................................Manual Transmission
72 Ground 3
73 Ground 4
74 Front Cigarette Lighter
75 Diode 3................................................................Automatic Transmission, MB
76 S/E Mode Selector Switch....................................Automatic Transmission
76-1Mode Switch........................................................Automatic Transmission
77 “B” Position Switch..............................................Automatic Transmission
78 “P” Position Switch..............................................Automatic Transmission
79 Shift Lock Solenoid Valve.....................................Automatic Transmission
8 0 TCCU
81 Ground 5.............................................................Gasoline E/G
81-1Ground 7.............................................................Diesel E/G
82 Seat Extension Wiring Connector
83 Transmission Extension Wiring Connector...........E23 & E32 Gasoline E/G with Manual Transmission
83-1 Transmission Extension Wiring Connector...........Diesel E/G with MB A/T
84 Transmission Extension Wiring Connector...........Gasoline E/G with Manual Transmission
84-1 Transmission Extension Wiring Connector...........Diesel E/G with Manual Transmission or BTRE A/T
85 Transmission Extension Wiring Connector...........E23 & E32 Gasoline E/G with A/T
85-1 Transmission Extension Wiring Connector...........Diesel E/G with BTRE A/T
86 Transfer Case Motor
87 Transfer Case Motor
88 Vehicle Speed Sensor
89 Fuel Gauge
90 Acceleration Sensor.............................................ABS 5.0
91 Seat Belt Switch (Passenger)
92 Seat Heater Switch
93 Head Lamp Leveling Device Switch.....................Leveling Device

9A-10 BODY WIRING SYSTEM
94 Seat Belt Switch (Driver)
95 Seat Belt Switch (Dirver)
96 Parking Brake Switch
97 Rear Cigarette Lighter
9 8 OVPR.................................................................Gasoline E/G
99 LH Side Repeater...............................................Rear Fog Lamp
100 Engine Wiring Connector
101 Engine Joint Connector
102 Engine Joint Connector......................................Gasoline E/G
103 ECS Engine Wiring Connector...........................Diesel E/G & Gasoline E/G with HFM ECU
104 ABD Engine Wiring Connector...........................ABD 5.0
105 ABD Engine Wiring Connector...........................ABD 5.0
105-1ABS Engine Wiring Connector............................ABS 5.0
106 Canister Purge Solenoid Valve...........................Gasoline E/G with MSE ECU
106-1Canister Purge Solenoid Valve...........................E20 & E23 Gasoline E/G with FHM ECU
107 Econo/Standard Solenoid Valve.........................Gasoline E/G with Automatic Transmission
108 CO Potentio Meter..............................................Gasoline E/G with HFM ECU & CO Potentio Meter
109 Front Wiper Motor
11 0 O
2 Sensor...........................................................E20 or E23 Gasoline E/G
111 RH Side Repeater
112 Engine Wiring Connector
113 Vertical Sensor
114 Lateral Sensor
115 Diagnosis
11 6 Joint Box.............................................................Gasoline E/G (E32)
117 Canister Purge Solenoid Valve...........................E32 Gasoline E/G with HFM ECU
118 Led Antenna......................................................Rolling code type Immobilizer
119 E-key Connector................................................Gasoline E/G with Rolling Code Type Immobilizer
120 Receiver Unit......................................................Gasoline E/G with Rolling Code Type Immobilizer
121 Receiver Unit......................................................Gasoline E/G with Rolling Code Type Immobilizer
122 Receiver Antenna..............................................Gasoline E/G with Rolling Code Type Immobilizer
123 Receiver Connector...........................................Gasoline E/G with Rolling Code Type Immobilizer
124 ICU Connector....................................................Gasoline E/G with Rolling Code Type Immobilizer
125 ICU .....................................................................Gasoline E/G with TOD (MSE ECU 3.2 Engine Only)
126 CAN Line............................................................Gasoline E/G with TOD (MSE ECU 3.2 Engine Only)
127 TOD ...................................................................Gasoline E/G with TOD (MSE ECU 3.2 Engine Only)
128 TOD ...................................................................Gasoline E/G with TOD (MSE ECU 3.2 Engine Only)
129 Transfer Case Speed Sensor.............................Gasoline E/G with TOD (MSE ECU 3.2 Engine Only)
130 Engine Main Wiring Connector...........................Gasoline E/G with MSE ECU
131 Remote Engine Start..........................................Diesel E/G with A/T & Black Out Lamp
132 Remote Engine Start..........................................Diesel E/G with A/T & Black Out Lamp
133 TCU ....................................................................Diesel E/G with BTRE A/T
134 TCU ....................................................................Diesel E/G with BTRE A/T
135 Ground 5............................................................Diesel E/G
136 Start Protection Relay.........................................Diesel E/G with Rolling Code Type Immobilizer
137 EGR control unit.................................................Diesel E/G
1 3 8 ICU 1..................................................................Diesel E/G with Rolling Code Type Immobilizer
1 3 9 ICU 2..................................................................Diesel E/G with Rolling Code Type Immobilizer
140 Injection Pump Valve Extension..........................Diesel E/G with Rolling Code Type Immobilizer
141 Injection Pump Valve Extension..........................Diesel E/G with Rolling Code Type Immobilizer
142 EGR Solenoid....................................................Diesel E/G
143 ICU led................................................................Diesel E/G with Rolling Code Type Immobilizer
144 Immobilizer Solenoid Valve..................................Diesel E/G with Crypto Type Immobilizer
147 Immobilizer Unit...................................................Diesel E/G with Crypto Type Immobilizer

INSTRUMENTATION/DRIVER INFORMATION 9E-3
COMBINATION METER
COMPONENT LOCATOR
1. Speedometer
2. Odometer
3. Trip odometer
4. Tachometer
5. Coolant temperature gauge
6. Fuel gauge
7. Low fuel level warning light
8. Turn signal indicator (left)
9. Turn signal indicator (right)
10. Outside rearview mirror & tailgate heating switch
11. Reset button
12. Auto shift indicator*
13. Door open warning light
14. TCS indicator (equipped with ABD)*
21. ABS warning light*22. EBD warning light*
23. ECS / SPORT warning light*
24. 4 - wheel warning light*
25. 4 - wheel high indicator
26. 4 - wheel low indicator
27. WINTER indicator
28. POWER indicator
29. High beam indicator
15. Alternator warning light
16. Engine oil pressure warning light
17. Brake system warning light
18. Glow indicator light (For Diesel engine)
19. Airbag warning light*
20. Seat belt reminder

SECTION 9H
SEATS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 9H-1
General Specifications . . . . . . . . . . . . . . . . . . 9H-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 9H-2
Schematic and Routing Diagrams . . . . . . . . 9H-3
Power Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 9H-3
Seat Warmer . . . . . . . . . . . . . . . . . . . . . . . . . . 9H-4Seat Belt & Tension Reducer Circuit . . . . . . . . 9H-5
Component Locator . . . . . . . . . . . . . . . . . . . 9H-6
Front Seat & Rear Seat . . . . . . . . . . . . . . . . . 9H-6
Maintenance and Repair . . . . . . . . . . . . . . . 9H-7
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 9H-7
SPECIFICATIONS
GENERAL SPECIFICATIONS
Slide
Tilt
Height
Tilt and Height(up)
Slide
Slide
Tilt and Height
Load Rating
Operating Temperature Range
Switch Operating Force Application
Deseription
DC11 - 15V
-30°C - 80°C
20 ± 7mm/sec
10.6 ± 5mm/sec
7 ± 2mm/sec
Tilt:35 ± 2mm, Height:35 ± 2mm
Forward:230mm
Less Then 7A
Less Then 7A
DC12V 1A
-30°C - 80°C
0.3 - 0.7Kgf Operating Voltage
Operating Temperature Range
Seat Operating Speed(at 13.5V)
Seat Operating Distance
Operating Current(at 13.5V)
Seat Heater Switch