check oil SSANGYONG MUSSO 2003 Owner's Manual

1B1-98 M162 ENGINE MECHANICAL
Tightening Torque 23 Nm
Notice Replace the oil filter gasket.
4. Installation should follow the removal procedure in the reverse order.
5. Check engine oil level.
6. Run the engine at idle and check the engine for leaks.
3. Remove the oil filter bolt and then remove the oil filter.
Installation Notice
Removal & Installation Procedure
1. Drain the coolant from the crank case.
2. Remove the each coolant line and hose.

M162 ENGINE MECHANICAL 1B1-103
OIL DIPSTICK GUIDE TUBE
1 Oil Dipstick Level Gauge
2 Oil Dipstick Guide Tube
Removal & Installation Procedure
1. Pull out the oil dipstick level gauge (1).
2. Remove the bolt (4) in the upper intake manifold and remove the oil dipstick guide tube. Installation Notice
3. Install new O-ring to the dipstick guide tube.
4. Installation should follow the removal procedure in the reverse order.
5. Check for leaks by starting the engine. 3 O-ring
4 Bolt (M6 x 12, 1 piece)
........................... 9-11 Nm
Tightening Torque 9 - 11 Nm

1B2-24 M161 ENGINE MECHANICAL5. Disconnect the vent hose from the A/C bracket.
6. Unscrew all the mounting bolts (arrows) and remove the A/C bracket and the gasket. Installation Notice
7. Clean the sealing surface.
8. Replace the gasket with new one.
9. Installation should follow the removal procedure in the reverse order.
10. Check the oil leakage by operating the engine after installation.
Tightening Torque 22.5 - 27.5 Nm

1B2-46 M161 ENGINE MECHANICAL
8. Unscrew the bolts (A).Installation Notice
Tightening Torque 22.5 - 27.5 Nm
9. Remove the belt pulley and vibration damper. Installation Notice (Center Bolt)
Tightening Torque 1st step 180 - 220 Nm 2nd step 80
° - 100 °
10. Unscrew the bolts (1, 2) on timing gear case cover and
remove the timing gear case cover. Installation Notice
Tightening Torque 22.5 - 27.5 Nm
Notice Be careful not to damage the cylinder head gasket.
11. Remove the radial shaft seal
NoticeInstallation note replace the seal with new one.
12. Clean the timing gear case cover and crankcase sealing surface.
13. Replace the O-ring with new one and apply the sealant on the sealing surface.NoticeBe careful not to stain the oil chamber of chain tensioner with the sealant.
14. Installation should follow the removal precedure in the reverse order.
15. Warm up the engine and check for oil leaks.

1B2-48 M161 ENGINE MECHANICAL
Tools Required
601 589 03 43 00 Sleeve Removal & Installation Procedure
1. Unscrew the bolts (1) and (5) and remove the closing coverby pulling the rear cover lug (arrows). Notice Be careful not to damage the oil pan gasket.
2. Clean the sealing surface of the crankcase and the rear sealing cover.
3. Check the radial shaft seal and replace it if necessary.
4. Apply the Loctite 573 to the rear cover sealing surface.
5. Apply the engine oil to the dust lip of the radial shaft seal.
NoticeDo not use the grease.
6. Using the special tool, press the radial shaft seal and the rear cover.
7. Tighten the rear cover bolt (1) and then tighten the oil pan bolt (5) as specified and remove the special tool. Installation Notice
Seal Assembler 601 589 03 43 00
Tightening Torque(Bolt 1,5) 9 - 11 Nm

1B2-52 M161 ENGINE MECHANICAL CRANKSHAFT FRONT RADIAL SEAL Preceding Work : Removal of belt pulley and vibration damper
1 Center Bolt (M18 x 50)............................... 1st step 200-220 Nm
2nd step 90° +10 °
2 Center Bolt Washer
3 Sleeve (Special Tool)
4 Crankshaft Front Seal
5 Key
Tools Required
601 589 03 14 00 Sleeve Replacement Procedure
1. Remove the radial seal with a screw driver.
Notice Use a clean cloth not to damage the radial seal mounting hole and the crankshaft.
5. Remove the sleeve and install the belt pulley and thevibration damper.
6. Check for leaks while operating the engine.
2. Coat the radial sealing lip with engine oil.
3. Using the sleeve, assemble the radial seal .
4. Align the sleeve groove and the woodruff key and tighten
the center bolt until the center bolt and the damper disk stop in the movement. Installation Notice
Tightening Torque 1st step 200 - 220Nm
2nd step 90
° + 10 °

M161 ENGINE MECHANICAL 1B2-53
CRANKSHAFT REAR RADIAL SEAL Preceding Work : Removal of flywheel or drive plate
1 Special Tool
2 Special Tool3 Crankshaft Rear Seal
Tools Required
601 589 03 43 00 Sleeve Replacement Proceudre
1. Remove the radial seal with a screw driver.
Notice Use a clean cloth not to damage the radial seal mounting hole and the crankshaft.
2. Install the special tool (2) to the crankshaft.
3. Apply the engine oil on the special tool (2).
NoticeDo not use the grease.
4. Install the radial seal on the inner parts assembler.
5. Press in the special tool (1) until the radial seal is stopped.
6. Check for leaks while operating the engine.

M161 ENGINE MECHANICAL 1B2-57
Installation Notice
Make sure the crankshaft bearing cap properly seated
in place in the crankcase side. When perfectly installed, the projected part (arrow) locates in the leftside (intake manifold side).
Assemble so that the projected part of the cap and
crankcase face the same direction.
Removal & Installation Procedure
1. Unscrew the connecting rod bearing cap bolt and remove
the bearing cap. Installation Notice
2. Unscrew the crankshaft bearing cap bolts and separate the upper and lower bearing shells and thrust washers. Installation Notice
Remove the bearing cap from front (pulley side) to
rear.
Make sure that the upper and lower bearing shells do
not change each other and coat with engine oil.
The oil grooves (arrows) in the thrust washers must
face outward and insert the thrust bearing into the bearing cap.
There are five kinds of thrust washers by thickness.
Select the proper washer when repaired.
3. Remove the crankshaft.
4. Installation should follow the removal procedure in the reverse order.
5. After completion of the installation, check for the rotating condition of the crankshaft.
Make sure that the upper and lower bearing shells do
not change each other.
Coat the bearing shell with engine oil.
Install the bearing cap according to the consecutive
number.
Part No. : 601 030 00 622.15 mm
Part No. : 601 030 01 62 2.20 mm
Part No. : 601 030 02 62 2.25 mm
Part No. : 601 030 03 62 2.30 mm
Part No. : 601 030 04 62 2.40 mm
Tightening Torque 40 Nm + 90 °
Tightening Torque 55 Nm + 90°

1B2-68 M161 ENGINE MECHANICAL
7. Remove the bearing cap, and remove the intake and theexhaust camshaft. Installation Notice
Tightening Torque 22.5 - 27.5 Nm
Notice Check the numbers on the bearing cap not to be miked up.
8. Apply the engine oil on the valve tappet and camshaft bearing.
9. Installation should follow the removal procedure in the reverse order. Notice
Base circle of cam should cantact with the valve tappet.
Install the camshaft bearing caps according to the
numbers on the cylinder head cast and bearing cap.
10. Check the camshaft timing position.

1B2-76 M161 ENGINE MECHANICAL
VALVE STEM SEAL Preceding Work : Removal of valve spring
1 Drift (Special Tool)
2 Valve Stem Seal
3 Protective Sleeve
Drift 119 589 00 43 00
Pliers 104 589 00 37 00
Tools Required
104 589 00 37 00 Pliers
119 589 00 43 00
Drift
Replacement Procedure
1. Remove the valve stem seal (2) using the pliers. Notice Check the valve stem seal for damage and replace if
necessary.
2. Coat the valve stem seal with oil and assemble it with the protective sleeve.
3. Insert the valve stem seal by pressing it with the drift.