key SSANGYONG NEW ACTYON SPORTS 2012 Workshop Manual

04-22
How to enter self-diagnosis mode ▶
Turn the ignition ON with the TRIP switch pressed.
Press and hold the TRIP switch for 5 to 10 sec. with the ignition ON.
Press and hold the TRIP switch for less than 10 sec. and then cycle the switch between ON
and OFF 5 times within 3 sec.
Confirm that the self-diagnosis mode is activated through the instrument cluster. 1.
2.
3.
4.
4. SELF-DIAGNOSIS CHECK
Self-diagnosis OFF ▶
If the engine speed increases to 396 rpm or more while the engine is cranking or the ignition key
is turned OFF in self-diagnosis mode, the self-diagnosis mode is turned OFF automatically.
Operating process ▶
Speed gauge: changes from 0 to 220 km
RPM gauge: changes from 0 to 6,000 rpm
Fuel gauge: changes from E to F
Temperature gauge: changes from C to H
Warning/Indicator lamps: All indicator/warning lamps controlled by MICOM are turned ON.
Dimming: Illuminates at the highest lighting level.
LCD display: All elements are activated. 1.
2.
3.
4.
5.
6.
7.

07-37810-01
1. OVERVIEW
The wiper and washer system are controlled by STICS according to driver's wiper switch
operation. And the detection of rain drops by rain sensor is transmitted to STICS as the signal for
wiper system control.
(saem as KYRON)
The characteristics of the wiper and washer system including basic functions of manual wiper are
as follows.
1) Wiper Function Coupled Auto Washer
Pressing the AUTO washer switch with the
ignition key OFF and INT AUTO switch OFF
sprays the washer fluid for 2 sec. and
operates the wiper 4 times and then
immediately sprays the washer fluid for 1.5
sec. and operates the wiper 3 times.
2) Integrated Auto Light Sensor in Rain Sensor Unit
The rain sensor unit is installed on the best
location to detect the rain drops and the
lighting intensity. And an auto light sensor is
newly integrated into the rain sensor unit for
more precise measurements. To control the
system, the sensed values of rain sensor and
auto light sensor are sent to pin no. 63 in
STICS unit. Auto
washer
operation
switch
(press)
Auto light
sensor
photodiode Rain sensor
emitter lens

07-77810-01
2) STICS Control Logic Related to Wiper and Washer
Wiper MIST and Front Washer Coupled Wiper ▶
The wiper relay is turned on 0.3 seconds after turning "ON" the washer switch for 0.1 ~
0.59 seconds with the ignition key "ON", and it is turned off when the parking terminal is
turned off. 1.
The wiper relay is turned on at 0.3 seconds after from the time when the washer switch is
turned on for more than 0.6 seconds with the ignition switch "ON". The wiper relay gets on
3 times immediately after turning off the washer switch. 2.

08-78610-09
3) Sensitivity Control
The wiper LOW relay is turned on and the wiper motor runs one cycle when the volume
<009a008c0095009a0090009b0090009d0090009b00a000470090009a004700900095008a0099008c0088009a008c008b0047004f008c009f00610047009a008c0095009a0090009b0090009d0090009b00a00047005700470d7d0047005800500047009e00
8f00900093008c0047009b008f008c00470090008e00950090>tion switch and the INT switch is
in the "ON" position, and the wiper motor is in "Parked" position). However, the wiper
motor can be operated only when the rain sensor detects the "Rain Detected" signal. 1.
If the volume sensitivity is changed more than 1 stage within 2 seconds, the wiper motor runs
only one cycle.
4) Auto Light Control
Only when the auto light switch is in "AUTO" position, it controls the tail lamp and
headlamp by communicating with the rain sensor (while the ignition key is in "ON"
position). 1.

08-8
5) When Wiper Parking Signal is Abnormal
The wiper system continuously outputs the parking signal of current sensitivity when the
parking terminal is grounded (while the ignition key is in "ON" position and the INT switch is
in "ON" position). 1.
When the parking terminal is fixed to IGN, the wiper system outputs the wiper operating
signal for 2 seconds, then continuously outputs the wiper parking signal.
※ The wiper motor runs only when the rain sensor requires the wiper operation. 2.

08-98610-09
6) Defective Rain Sensor
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 3 from 4 during receiving the malfunction signal from the rain
sensor, while the ignition key is in "ON" position and the wiper switch is in "ON" position. 2.The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 2 from 3 during receiving the malfunction signal from the rain
sensor, while the ignition key is in "ON" position and the wiper switch is in "ON" position. 1.

08-10
7) Speed Sensitive INT Wiper
Calculates and converts the Intermittent interval automatically by obtaining the INT VOLUME
when the ignition switch and the INT switch is in the "ON" position.
The wipers are operated in vehicle speed sensitive mode as soon as turning the INT auto
switch to the "ON" position with the ignition key ON or turning the ignition key to the "ON"
position with the INT auto switch ON.
This applies to the vehicle without the rain sensor. -
-
※
Controls the wiper intermittent operation by the values from the vehicle speed and the setting
value.

09-4
2. CAUTIONS
Note that the display does not show everything in the rear area. Always check nobody,
especially animals and children, is behind the vehicle when parking or reversing.
If you can not properly check the vehicle behind, get out of the vehicle and then visually
check it.
The parking aid system is just a supplemental device to help your parking.
Always keep the safety precautions.
Do not press or shock the sensors by hitting or using a high-pressure water gun while
washing, since it may damage the sensors.
If the system is in normal operating condition, a short beep sounds when the shift lever is
moved into "R" position with the ignition key "ON". -
-
-
-
-
-
The parking aid system will not work or improperly work under following cases: ▶
1. Certain obstacles that sensors can not detect
Thin and narrow objects, such as wires, ropes, chains
Cotton, sponge, clothes, snow; that absorb ultrasonic waves
Obstacles lower than the bumper (ex. drain ditch or mud puddle) -
-
-
2. Not defective but improperly working
When the sensing portion is frozen (operates normally after thawed)
When the sensing portion is covered by rain, water drops, snow or mud (operates normally
after cleaned)
When receiving other ultrasonic signals (metal sound or air braking noises from heavy
commercial vehicles)
When a high-power radio is turned on -
-
-
-
3. Narrowed sensing area
When the sensing portion is partially covered by snow or mud (operates normally after
cleaned)
<007a009c009900990096009c0095008b00900095008e0047009b008c00940097008c00990088009b009c0099008c00470096008d0047009a008c0095009a0096009900470090009a0047009b009600960047008f0090008e008f0047004f00880097009700
990096009f005500470096009d008c00990047005f005700b6>C) or too low (approx.
below -30°C) -
-
When driving on the rough roads, gravel road, hill and grass
When the bumper height is changed due to heavy load
When the sensing portion is frozen
When the sensing portion is covered by rain, water drops, snow or mud
When receiving other ultrasonic signals (metal sound or air braking noises from heavy
commercial vehicles)
When a high-power radio is turned on
When some accessories are attached in detecting ranges -
-
-
-
-
-
- 4. Not defective but may cause malfunction

10-6
2. SWITCH
No. Name and Function
1 RDS setup
2 AF/TA selection
3 Start call
4 USB, AUX, CD selection
5 Power (ON/OFF), Mute, Volume
6 Preset key #1, Intro SCAN
7 Preset key #2, RPT
8 Preset key #3, Random
9 Preset key #4, folder down
10 Preset key #5, folder up
11 Preset key #6, File guide
12 AST, SCAN, TUNE UP/DOWN
13 Eject
14 End call
15 Set
16 Band
17 LCD window

02-93170-01
Ring - Snap
Ring - Snap
Bearing - Ball
Pinion assembly - Main drive
Bearing - Needle roller
Ring - Synchronizer
Ring - Snap
Sleeeve - Synchronizer
Key assembly - Synchronizer
Hub - Synchronizer
Ring assembly - Triple cone
Gear assembly - 3rd speed
Bearing - Needle roller
Shaft - Main
Gear assembly - 2nd speed
Bearing - Needle roller
Ring assembly - Triple cone
Hub - Synchronizer
Sleeeve - Synchronizer 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.Ring assembly - Triple cone
Gear assembly - 1st speed
Sleeve - 1st gear
Bearing - Double angular ball
Ring - Snap
Gear - Main shaft 5th
Spacer
Gear - Main shaft 6th
Sleeve - Reverse gear
Bearing - Needle roller
Gear assembly - Reverse speed
Ring assembly - Triple cone
Hub - Synchronizer
Sleeeve - Synchronizer
Stopper - Synchronizer key
Bearing - Ball
Flange assembly - Companion
O-ring
Nut - Locking (4WD: 245.1 ~ 264.7 Nm,
2WD: 117.6 ~ 137.2 Nm) 20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.