Specification SSANGYONG TURISMO 2013 Owner's Guide

08-4
2. FASTENER TIGHTENING SPECIFICATIONS

09-4
2. FASTENER TIGHTENING SPECIFICATIONS
1) Temperature vs Resistance

01-38410-02
1. CAUTIONS WHEN WORKING ON ELECTRICAL UNITS
80℃
10A 15A
Disconnect the negative cable from the
battery in advance when working on electrical
units. -
Make sure to turn "OFF" the ignition switch
and other lamp switches before
disconnecting or connecting the negative
battery cable. (Otherwise, semiconductor
parts can be damaged.)
Do not drop or appy excessive impact to
sensors and relays. -
If a fuse is blown, replace it with a fuse which
has the correct amperage rating. If you use a
fuse with higher capacity than the
specification, the component can be
damaged or catch fire. -

02-38710-01
1. SPECIFICATIONS OF RK - STICS
1) Electrical Performance
2) Chattering of Input Signals
Vehicle speed input:
The vehicle speed calculating time is 1.0 seconds. The elapsed time of 1.5 seconds after IGN
1 switch :ON” is not included.
20 ms target input:
Wiper motor A/S (parking) terminal
100 ms target input switch
All switches except wiper motor A/S (parking) terminal 1.
2.
3.
3) Time Tolerance
If not indicated, time tolerance will be ± 10%.
However, if less than 500 ms, time tolerance will be ± 50 ms.
The time indicated in each function does not include chattering processing time from switch
input changing point. 1.
2.
Item Requirement Remark
Rated voltage DC 12 V
Operating voltage DC 9 to 16 V Should operate normally within this range.
Operating temperature-30℃ ~ +80℃
Reserved temperature-40℃ ~ +85℃
Max. operating humidity 95%
Resistible voltage 24 V
Insulating resistance No heat and fire due to
the current leaks.Confined with PCB, waterproof and coating that
requires the insulation.
Parasitic current below 4.0 mA
(below 6.0 mA)IGN = OFF, Full output load = OFF, 90
seconds (after received the signals), No input
changes for 2 seconds
Voltage drop below 1.2 V
below 2.0 VPin no. 8 and 2, 3, 5, 7, 10, 12, 13, 15, 19, 20,
23, 40, 47, 51, 53, 54
Pin no. 8 and 1, 14

03-37010-06
1. SPECIFICATIONS
Item Item Specification
Immobilizer
unitOperating voltage
(CAN) 6.0 V to 16.0 V
(6.0 V ~18.0 V)
Operating temperature-30℃ ~ 80℃
Coil inductance420 uH ± 20 uH
Modulation methodFSK
(Frequency Shift Keying : frequency
displacement)
Frequency134.2 KHz ± 4 KHz
TransponderFrequency134.2 KHz ± 4 KHz
Operating temperature-40℃ ~ +85℃
Transponder coding Up to 5
2. CAUTIONS
The vehicle owner must observe the service works when deleting the transponder codes or
registering additional keys.
In any cases, the immobilizer system can not be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove,
damage or modify it.
The remote engine starter cannot be installed to the vehicle equipped with the immobilizer
system.
Do not drop or shock to the transponder in the ignition key as it may be damaged.
With a damaged transponder, the engine cannot be started.
For the vehicle with the immobilizer, there can be a problem in starting the vehicle or the system
error: 1.
2.
3.
4.
5.
6.
When more than one immobilizer keys come into contact with (each) other(s) or key is close
to any device sending or receiving electromagnetic fields or waves
When the ignition key is close to any electronic or electric devices such as lighting equipment,
security keys or security cards
When the ignition key is close to a magnetic or metal object or a battery -
-
-

04-38010-01
1. SPECIFICATIONS
1) Power, Voltage, Current
Description Specification
Rated voltage DC 12V
Operating voltage DC 9V ~ 16V
Inspection voltage DC 13.5V
Operating temperature Standard-30˚C ~ +75˚C (while driving)
Black face-30˚C ~ +80˚C
Storage temperature-40˚C ~ +85˚C
Performance guarantee voltage DC 10V ~ 15V
Dark current Standardbelow 3mA (12V, 25°C), Stabilized conditions (standby
mode) around 180 seconds after IGN OFF
Black facebelow 1mA (12V, 25°C), Stabilized conditions (standby
mode) around 180 seconds after IGN OFF

04-4
2) LCD Display
Description Specification
Color of display Black
Color of back-light Yellow/Green
Running type 1/4 Duty, 1/3 Bias
(1) Standard
(2) Black face
Description Specification
LCD display type Speedometer (segment)
LCD display
SpecificationSelective display TRIP A
TRIP B
Driving time
Average speed
Average fuel economy
Distance to empty
Illumination control
Constant display Odometer
Instant fuel economy
Gear selector lever position

07-38310-01
1. BULB SPECIFICATIONS
Description AmountSpecification
(EU)Specification
(General)
Exterior
lampHeadlamp High beam + DRL 2 55W + 15W 55W
Low beam 2 55W←
Turn signal lamp 2 21W←
Position lamp 2 5W←
Front fog lamp 2 H16←
Side repeater 2 5W←
Rear
combination
lampTail (stop) lamp 4 5W(21W)←
Turn signal lamp 2 21W←
Back-up lamp 2 16W←
Rear fog lamp 2 21W -
License plate lamp 2 5W←
High mounted stop lamp 5 5W←
Interior lamp Front room lamp 2 5W←
Glove box lamp 1 5W←
Door courtesy lamp 4 5W←
Side room lamp 4 5W←
Rear room lamp 1 5W←

06-38510-00
1. SPECIFICATIONS
1) Center Fascia Switch
Item Specifications
Center fascia switch &
bezel assemblyHazard warning flasher switch DC 12 V 10 A(lamp load)
Windshield heated glass switch
DC 12 V 1 A(inductive load) Rear heated glass switch
ESP OFF switch
Driver/front passenger seat warmer
switch
Fog lamp switch
2) 4WD Switch & HLLD Switch & Rear Wiper Operation Switch
Item Specifications
4WD switch &
HLLD switch &
rear wiper operation
switch assemblyWasher switch DC 12 V 3.8 A(lamp load)
Wiper switch DC 12 V 3.0 A (max. 10 A)
4WD switch DC 12 V 300 mA
HLLD switch DC 12 V 1 A (inductive load)
3) Steering Wheel Switch
Item Specifications
Steering wheel switch Rated voltage DC 5 V 0.1 A(rated load)
Operation temperature-30℃~+80℃

07-37810-01
1. SPECIFICATIONS OF WIPER