Belt SUBARU TRIBECA 2009 1.G Service Owner's Manual
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2009, Model line: TRIBECA, Model: SUBARU TRIBECA 2009 1.GPages: 2453, PDF Size: 46.32 MB
Page 77 of 2453

AB(diag)-53
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
B: DTC 12 PASSENGER'S AIRBAG FAILURE
DTC DETECTING CONDITION:
•Airbag main harness circuit is open, shorted or shorted to ground.
•Airbag module harness (Passenger's side) circuit is open, shorted or shorted to ground.
•Passenger's airbag module is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB-00663
AB6
AB9
AB9
AB10
1110
34
78
12
AB6
1234567891011121314151617
1819202122232425262728
INFLATOR(PASSENGER SIDE)
AIRBAG CONTROL MODULE
1234
Page 80 of 2453

AB(diag)-56
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
C: DTC 15 DRIVER'S AIRBAG FAILURE
DTC DETECTING CONDITION:
•Airbag main harness circuit (Driver's side) is shorted to power supply.
•Airbag module harness circuit (Driver's side) is shorted to power supply.
•Roll connector is shorted to power supply.
•Driver's airbag module is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
NOTE:
Prior to starting work, prepare two airbag resistors (98299PA040).
WIRING DIAGRAM:
AB-01300
16171314
AB6
AB2
AB2
AB71234
AB6
AB381212
21
AB38
AB37
123421
AB37
1234567891011121314151617
1819202122232425262728
AIRBAG CONTROL MODULE
STEERINGROLL CONNECTOR
INFLATOR(DRIVER SIDE)
Page 83 of 2453

AB(diag)-59
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
D: DTC 16 PASSENGER'S AIRBAG FAILURE
DTC DETECTING CONDITION:
•Airbag main harness circuit (Passenger's side) is shorted to power supply.
•Airbag module harness circuit (Passenger's side) is shorted to power supply.
•Passenger's airbag module is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB-00663
AB6
AB9
AB9
AB10
1110
34
78
12
AB6
1234567891011121314151617
1819202122232425262728
INFLATOR(PASSENGER SIDE)
AIRBAG CONTROL MODULE
1234
Page 85 of 2453

AB(diag)-61
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
E: DTC 21 AIRBAG ECU FAILURE
DTC DETECTING CONDITION:
Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
Step Check Yes No
1CHECK IF DTC 21 IS INDICATED.
Read the DTC.
OPERATION, Subaru Select Monitor.>
Is DTC 21 indicated for airbag
warning light?
Replace the airbag
control module.
Module.>
Per fo r m th e cl ea r
memory mode.
ORY MODE,
OPERATION,
Subaru Select
Monitor.>
Page 87 of 2453

AB(diag)-63
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
This DTC is indicated when the front airbag module and the pretensioner are deployed.
Once this DTC is displayed, the memory cannot be cleared. Therefore replace the following parts.
•Airbag control module
•Driver's airbag module
•Passenger's airbag module
•Front sub sensor of both sides
•Front seat belt outer with pretensioner of both sides.
•Steering roll connector
•Occupant detection system (passenger’s seat cushion & frame assembly)
G: DTC 23 CONNECTOR TO AIRBAG ECU FAILURE
DTC DETECTING CONDITION:
Connection of (AB6), (AB17) and (AB18) to airbag control module is improper.
CAUTION:
Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
Step Check Yes No
1CHECK POOR CONTACTS OF CONNEC-
TORS (AB6), (AB17) AND (AB18).
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connectors (AB6), (AB17)
and (AB18) from airbag control module.
Is there rust or damage on the
harness connector and the
control module connector?
Replace the airbag
control module.
Module.> Replace
the body harness
with the airbag
main harness or
replace the body
harness with the
side airbag har-
ness.
Go to step 2.
2CHECK POOR CONTACTS OF CONNEC-
TORS (AB6), (AB17) AND (AB18).
1) Reconnect the connector securely.
2) Connect the battery ground terminal and
turn the ignition switch to ON.
Does the airbag warning light
illuminate for 6 seconds and go
off?
Go to step 3.Replace the airbag
control module.
Module.>
3CHECK AIRBAG CONTROL MODULE.
1) Connect all the connectors.
2) Erase the memory.
3) Perform the inspection mode.
4) Read the DTC.
Is the same DTC displayed? Replace the airbag
control module.
Module.>
Go to step 4.
4CHECK ANY OTHER DTC ON DISPLAY.Is any other DTC displayed? Check DTC using
“List of Diagnostic
Tr o u b l e C o d e
(DTC)”.
of Diagnostic Trou-
ble Code (DTC).>
Finish the diagno-
sis.
Page 88 of 2453

AB(diag)-64
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
H: DTC 24 IG1 OPEN
DTC DETECTING CONDITION:
•Airbag control module is faulty.
•Airbag main harness circuit is open.
•Fuse No. 12 (in joint box) is blown.
•Body harness circuit is open.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB6
AB6
NO.12
5
AB-00939
1234567891011121314151617
1819202122232425262728
IGNITIONSWITCH
BATTERY
AIRBAG CONTROL MODULE
B31
AB110
AB1
123456789101112
Page 90 of 2453

AB(diag)-66
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
I: DTC 25 IG2 OPEN
DTC DETECTING CONDITION:
•Airbag control module is faulty.
•Airbag main harness circuit is open.
•Fuse No. 25 (in joint box) is blown.
•Body harness circuit is open.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB6
B31
AB1
AB6
NO.25
6
AB-00938
1234567891011121314151617
1819202122232425262728
IGNITIONSWITCH
BATTERY
AIRBAG CONTROL MODULE
9
AB1
123456789101112
Page 92 of 2453

AB(diag)-68
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
J: DTC 26 PASSENGER'S AIRBAG INDICATOR FAILURE
DTC DETECTING CONDITION:
•Passenger's seat airbag indicator is faulty.
•Airbag control module is faulty.
•Airbag main harness circuit is open.
•Body harness circuit is open.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag harness, disconnect the each airbag module connector, and seat belt
pretensioner for safety reasons.
WIRING DIAGRAM:
AB-01301
118
AB6
AB1
AB1
B3162
i116
i2
B403
56
65
AB6i116
AIRBAG CONTROL MODULE
WARNING BOX(PASSENGER SIDE)
1234567891011121314161715
1819202122232425262728
12346789510123456789101112
B403
123456789
1611101514131217 191823 252420 2221
Page 95 of 2453

AB(diag)-71
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
L: DTC 29 ODS FAILURE
NOTE:
Refer to “Occupant Detection System” for details on DTC 29.
M: DTC 2A OCCUPANT DETECTION CALIBRATION FAILURE
NOTE:
Refer to “Occupant Detection System” for details on DTC 2A.
N: DTC 2B ODS ERRONEOUS PARTS
NOTE:
Refer to “Occupant Detection System” for details on DTC 2B.
O: DTC 2C BELT TENSION SENSOR FAILURE
NOTE:
Refer to “Occupant Detection System” for details on DTC 2C.
5CHECK THE AIRBAG HARNESS.
Measure the voltage between connector (2AB)
in the test harness AB and chassis ground.
Connector & terminal
(2AB) No. 1 — chassis ground:
Is the voltage more than 9 V? Replace the airbag
rear harness RH
with body harness.
Replace the occu-
pant detection har-
ness (seat
harness). If defec-
tive is not
improved, replace
the occupant
detection system
(seat cushion &
frame assembly),
and then the air-
bag control mod-
ule in this order.
Step Check Yes No
Page 96 of 2453

AB(diag)-72
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
P: DTC 31 FRONT SUB SENSOR RH FAILURE
DTC DETECTING CONDITION:
•Front sub sensor harness (RH) circuit is shorted.
•Front sub sensor harness (RH) circuit is open.
•Front sub sensor (RH) is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB-00667
AB6
AB16
AB6
209
1 2
AB16
121234567891011121314151617
1819202122232425262728
AIRBAG CONTROL MODULE
FRONT SUB SENSOR RH