SUZUKI ALTO 2013 7.G Workshop Manual
Manufacturer: SUZUKI, Model Year: 2013, Model line: ALTO, Model: SUZUKI ALTO 2013 7.GPages: 190, PDF Size: 8.76 MB
Page 51 of 190
2-32
BEFORE DRIVING
53MH0-74E
Electric Power Steering Light
(if equipped)
53M-04-077
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started.
If this light comes on while driving, the
power steering system may not work prop-
erly. Have the system inspected by your
MARUTI SUZUKI dealer.
NOTE:
If the power steering system does not work
properly, you will feel heavier to steer but
you still will be able to steer.
Oil Pressure Light
53M-04-078
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. Thelight will come on and remain on if there is
insufficient oil pressure. If the light comes
on when driving, pull off the road as soon
as you can and stop the engine.
Check the oil level and add oil if necessary.
If there is enough oil, the lubrication sys-
tem should be inspected by your MARUTI
SUZUKI dealer before you drive the vehi-
cle again.
Charging Light
53M-04-079
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. The
light will come on and remain on if there is
something wrong with the battery charging
system. If the light comes on when the
engine is running, the charging system
should be inspected immediately by your
MARUTI SUZUKI dealer.
High Engine Coolant Temperature
Warning Light
53M-04-080
When the ignition switch is turned to the
“ON” position, this light comes on briefly so
you can check that the light is working. If
this light blinks while driving, it means the
engine is running hot. Avoid driving condi-
tions that may lead to actual overheating. If
NOTICE
• If you operate the engine with this
light on, severe engine damage can
result.
• Do not rely on the Oil Pressure
Light to indicate the need to add
oil. Be sure to periodically check
the engine oil level.
Page 52 of 190
2-33
BEFORE DRIVING
53MH0-74E
the light stays on without blinking, then the
engine is overheating. Follow the instruc-
tions in the “If the Engine Overheats” of
“EMERGENCY SERVICE” section.
Immobilizer System Light
53M-04-081
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. If this
light blinks with the ignition switch turned to
“ON”, there may be something wrong with
the immobilizer system. Ask your MARUTI
SUZUKI dealer to have the system
inspected.
Door Lock Canceller Indicator Light
(if equipped)
53M-04-082
This indicator light will come on and keep
blinking continuously if there is some prob-
lem with door lock canceller system. Have
the vehicle inspected by MARUTI SUZUKI
authorized dealer.
NOTE:
In case door lock wiring and/or motor
are
damaged, Door Lock Canceller Indicator
Light will not blink.
Gear Shift Indicator (if equipped)Manual Transaxle
53M-04-083
This indicator informs about upshifting or
downshifting the gear while the vehicle is
running.There are three indications:
Upshift Indicator
This symbol indicates that lower gear posi-
tion is selected for vehicle’s current speed
and / or engine revolution. Changing to
higher gear position is recommended.
Stay Indicator
This symbol indicates that current gear
position is optimal for vehicle’s current
speed and / or engine revolution. No gear
shifting is required.
NOTE:
While driving in optimal gear position, the
upshift/downshift indicator does not
appear.
Downshift Indicator
This symbol indicates that higher gear
position is selected for the vehicle’s current
speed and / or engine revolution. Changing
to lower gear position is recommended.
NOTICE
Continuing to drive the vehicle when
engine overheating is indicated can
result in severe engine damage.
Page 53 of 190
2-34
BEFORE DRIVING
53MH0-74E
Turn Signal Indicators
53M-04-084
When you turn on the left or right turn sig-
nals, the corresponding green arrow on the
instrument panel will flash along with the
respective turn signal lights. When you
turn on the hazard warning switch, both
arrows will flash along with all of the turn
signal lights.
Main Beam (high beam) Indicator
Light
53M-04-085
This indicator comes on when headlight
main beams (high beams) are turned on.
Front Fog Light Switch (if
equipped)
53M-04-086
The front fog light comes on when front fog
light operates.
Speedometer
ALTO 800
Ty p e 1
53M-04-087
Ty p e 2
53MH0238
EXAMPLE
EXAMPLE
Page 54 of 190
2-35
BEFORE DRIVING
53MH0-74E
ALTO K10
Ty p e 1
53M-04-088
Ty p e 2
53M-04-089
The speedometer indicates vehicle speed
in km/h.
Fuel Gauge
ALTO 800
Ty p e 1
53M-04-090
Ty p e 2
53MH0239
ALTO K10
Without tachometer
53M-04-091
With tachometer
53M-04-092
Automated Manual Transaxle
53M-04-093
When the ignition switch is in the “ON”
position, this gauge gives an approximate
indication of the amount of fuel in the fuel
tank. “F” stands for full and “E” stands for
empty.
The mark (1) indicates that the fuel filler
door is located on the left side of the vehi-
cle.
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
(1)
EXAMPLE
EXAMPLE
EXAMPLE
Page 55 of 190
2-36
BEFORE DRIVING
53MH0-74E
When the fuel meter indicator shows only
one segment to “E”, refill the tank as soon
as possible.
NOTE:
• If the last segment blinks, it means that
the fuel is almost empty.
• The fuel meter indicator varies depend-
ing on road conditions (for example,
slope or curve) and driving conditions
because of fuel moving in the tank.
Depress Brake Pedal Indicator
(if equipped)
53M-04-094
Information Display
ALTO 800
53MM02003
53M-04-095
(1) Clock (if equipped)
(2) Odometer/Trip meter
(3) Odometer/Trip meter/Meter illumina-
tion control knob
ALTO K10
Manual transaxle
Without tachometer
53M-04-096
With tachometer
53M-04-097
Automated Manual transaxle
Without tachometer
53M-04-098
(1) (2)(3)
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
Page 56 of 190
2-37
BEFORE DRIVING
53MH0-74E
With tachometer
53M-04-099
Clock (1) (if equipped)
The clock is shown when the ignition
switch is in the “ON” position.
To set the clock, follow the instructions
below.
Hold in the indication selector and meter
illumination control knob (3) for more
than 2 seconds. Push the indication
selector and meter illumination control
knob (3) to advance the minute display
while the minute display is flashing.
Release the indication selector and
meter illumination control knob (3) for 5
seconds to set the minute display.
The hour display flash after the minute
display is set. Push the indication selec-tor and meter illumination control knob
(3) to advance the hour display. Release
the indication selector and meter illumi-
nation control knob (3) for 5 seconds to
set the hour display.
Odometer/Trip meter (2)
The odometer/trip meter is shown when
the ignition switch is in the “ON” position.
The odometer records the total distance
the vehicle has been driven. The trip meter
can be used to measure the distance trav-
eled on short trips or between fuel stops.
53M-04-100
When the ignition switch is turned to “ON”
with the lighting switch is in the “OFF” posi-
tion, the display shows three types of indi-
cation; odometer (A), trip meter A (B), trip
meter B (C) and clock (D). Push the
“MODE” knob (3) quickly to switch the indi-
cation among the four.
53M-04-101
WA R N I N G
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
Do not attempt to adjust the display
while driving.
EXAMPLE
NOTICE
Keep track of your odometer reading
and check the maintenance sched-
ule regularly for required services.
Increased wear or damage to certain
parts can result from failure to per-
form required services at the proper
mileage intervals.
EXAMPLE
EXAMPLE
Page 57 of 190
2-38
BEFORE DRIVING
53MH0-74E
When the ignition switch is turned to “ON”
and the position lights, tail lights and/or the
headlights are on, the display shows four
types of indication; odometer (A), trip
meter A (B), trip meter B (C), clock (D) and
indication of illumination intensity (E). Push
the “MODE” knob (3) quickly to switch the
indication among the five. When the indica-
tion shows (E), you can control the meter
illumination intensity. Refer to “Meter illumi-
nation control” section below for details on
how to dim or brighten the meter illumina-
tion.
53M-04-102
To reset the trip meter to zero, hold in the
“MODE” knob (3) for about 2 seconds.Meter illumination control
53M-04-103
When the display shows the indication of
illumination intensity (E), you can dim or
brighten the meter illumination.
To change the meter illumination bright-
ness, continue to hold in the “MODE” knob
(3). The indication will change as shown in
the illustration. The illumination gets dim-
mer then returns to the brightest condition
after it reaches the dimmest.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the brightness of the
instrument panel lights will be reinitialized.
Readjust the brightness according to your
preference.
Lighting Control Lever
53M-04-104EXAMPLE
EXAMPLE
EXAMPLE
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE
Page 58 of 190
2-39
BEFORE DRIVING
53MH0-74E
Lighting Operation
Ty p e 1
53M-04-105
Ty p e 2
53M-04-106
To turn the lights on or off, twist the knob
on the end of the lever. There are three
positions:OFF (1)
All lights are off.
(2)
Front position lights, tail lights, license
plate light and instrument lights are on, but
headlights are off.
(3)
Front position lights, tail lights, license
plate light, instrument lights and head
lights are on.
Ty p e 1
53M-04-107
Ty p e 2
53M-04-108
With the headlights on, push the lever for-
ward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To momen-
tarily activate the high beams (main
beams) as a passing signal, pull the lever
slightly toward you and release it when you
have completed the signal.
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
Page 59 of 190
2-40
BEFORE DRIVING
53MH0-74E
Headlight Leveling Switch
53M-04-109
Level the headlight beam according to the
load condition of your vehicle by turning
this switch. The chart below shows the
appropriate switch position for different
vehicle-load conditions.
Turn Signal Control Lever
53M-04-110
Turn Signal Operation
With the ignition switch in the “ON” posi-
tion, move the lever up or down to activate
the right or left turn signals.
Normal turn signal
Ty p e 1
53M-04-111
Move the lever all the way upward or down-
ward to signal. When the turn is com-
pleted, the signal will cancel and the lever
will return to its normal position.
Ty p e 2
53M-04-112
Vehicle
Load
ConditionSwitch Position
Alto 800 Alto K10
Petrol CNG Petrol CNG
Driver only0000
Driver + 1
passenger
(in front
seat)0000
Driver + 4
passen-
gers, No
cargo1111
EXAMPLE
Driver + 4
passen-
gers,
Cargo
added2NA3NA
Driver +
Full cargo3NA4NA
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE
EXAMPLE
EXAMPLE
Page 60 of 190
2-41
BEFORE DRIVING
53MH0-74E
Lane change signal
Ty p e 1
53M-04-113
Ty p e 2
53M-04-114
Sometimes, such as when changing lanes,
the steering wheel is not turned far enough
to cancel the turn signal. For convenience,
you can flash the turn signal by moving the
lever part way and holding it there. The
lever will return to its normal position when
you release it.
Hazard Warning Switch
53MH0227
Push in the hazard warning switch to acti-
vate the hazard warning lights. All turn sig-
nal lights and both turn signal indicators
will flash simultaneously. To turn off the
lights, push the switch again.
Use the hazard warning lights to warn
other traffic during emergency parking or
when your vehicle could otherwise become
a traffic hazard.
Windshield Wiper and Washer
Lever
65D611
Wiper and Washer Operation
When the ignition switch is in the “ON”
position, you can use the wiper/washer
lever or switch (if equipped).
EXAMPLE
EXAMPLE
EXAMPLE
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE