torque SUZUKI SWIFT 2000 1.G Transmission Service Repair Manual

7B-124 AUTOMATIC TRANSMISSION (4 A/T)
22) Install thrust needle roller bearing (3).
23) Install thrust washer (2).
24) Install new gasket to transmission case and install rear cover
(1).
Tightening torque
Rear cover bolts
(a) : 19 N·m (1.9 kg-m, 14.0 lb-ft)
25) Measure clearance between thrust washer and rear cover in
the following manner.
Measure the shaft and play of planetary set (1) with dial
gauge (2).
If the obtained clearance is out of specification, select the
thrust washer from table below and repeat above steps 22) –
24) to obtain the clearance within specification.
Clearance between thrust washer and rear cover
Standard : 0.3 – 0.7 mm (0.012 – 0.028 in.)
Available thrust washer (thickness)
: 1.9 mm (0.075 in.), 2.2 mm (0.087 in.), 2.5 mm (0.098 in.)
or 2.8 mm (0.110 in.)
1. Rear cover
4. Gasket(a)
NOTE:
Install the hook (2) to the location shown in figure.
NOTE:
Make sure that tip of dial gauge is not in contact with
counter drive gear (3).

AUTOMATIC TRANSMISSION (4 A/T) 7B-125
26) Attach parking lock rod (2) to manual shift shaft (1).
27) Install manual shift shaft and washer (3) to transmission
case. Fix manual shift shaft with washer, control shift lever
(4) and two nuts (5).
Apply grease to the washers.
Tightening torque
Control shift lever nuts
(a) : 30 N·m (3.0 kg-m, 22.0 lb-ft)
“A” : Grease 99000-25030
28) Install detent spring (1) to transmission case.
Tightening torque
Detent spring bolt (a) : 11 N·m (1.1 kg-m, 8.0 lb-ft)
29) Install thrust needle roller bearing (2) on counter bearing (3).
30) Install counter driven gear (1).
31) Install parking lock pawl sleeve (1) and oil plate (not shown
in figure).
Tightening torque
Parking lock pawl sleeve bolt
(a) : 19 N·m (1.9 kg-m, 14.0 lb-ft)

7B-126 AUTOMATIC TRANSMISSION (4 A/T)
32) Install parking lock pawl (2).
33) Install parking lock pawl shaft (4), torsional spring (3), and
cover (1), then hold them with 2 bolts.
Tightening torque
Parking lock pawl bolts (a) : 11 N·m (1.1 kg-m, 8.0 lb-ft)
34) Install reverse brake (B2) plates, discs, flange and cushion
plate in following order :
(1) Cushion plate →
(2) Plate →
(3) Disc →
(4) Plate →
(5)
Disc →
(6) Plate →
(7) Disc →
(8) Plate →
(9) Disc →
(10)
Flange
35) Hold above parts with snap ring.
NOTE:
 Note the direction of cushion plate (1).
 Make sure that the plates are fitted into groove of
transmission case as shown in figure.
2. Brake plate side
3. Transmission case side

AUTOMATIC TRANSMISSION (4 A/T) 7B-129
44) Apply grease to thrust needle roller bearing (1) and install it.
“A” : Grease 99000-25030
45) Apply grease to clutch drum thrust washer (1) and install it to
oil pump assembly (2).
“A” : Grease 99000-25030
46) Install new gasket to transmission case and install oil pump
assembly (1) to transmission case.
Tightening torque
Oil pump assembly bolts (a) : 12 N·m (1.2 kg-m, 9.0 lb-ft)
47) Measure input shaft end (2) play.
Set dial gauge (1) as shown in figure and measure the play
of the input shaft.
Input shaft end Play
Standard : 0.3 – 0.7 mm (0.012 – 0.028 in.)
48) If the obtained value is out of standard value, select thrust
bearing race (installed in step 41)) of different thickness
shown in table below and adjust the play.
Available thrust bearing race size (thickness)
1.3 mm (0.051 in.), 1.7 mm (0.067 in.) or 2.1 mm (0.083 in.)
3. Oil pump

7B-130 AUTOMATIC TRANSMISSION (4 A/T)
49) Install differential gear assembly (1).
50) Install thrust bearing race (1) and thrust needle roller bearing
(2) to the top of counter driven gear (3).
51) Apply grease to oil pump D-ring.
Install new gasket to transmission case and install torque
converter housing (1).
Tightening torque
Torque converter housing bolts
(h) : 19 N·m (1.9 kg-m, 14.0 lb-ft)
Grease 99000-25030
“A” : Thread lock cement 99000-32110 NOTE:
Grease can be applied around the R and L bearing of dif-
ferential gear assembly to ease fitting to the transmis-
sion case and torque converter housing.
NOTE:
Apply thread lock to the three bolts shown in figure.
2. New bolt

AUTOMATIC TRANSMISSION (4 A/T) 7B-131
52) Install O-rings to each accumulator piston and apply grease
or ATF to them.
Grease 99000-25030
53) Install C1 and B0 accumulator pistons (1 and 6), springs (2,
3 and 7) and spacers (4).
Hold them with snap rings (5).
54) Install C0, B1, C2 accumulator springs (9, 12, 13, 15 and
16), spacer (11) and pistons (8, 10 and 14) as shown in fig-
ure.
55) Install wire-to-solenoid assembly (1).
Tightening torque
Wire - to - solenoid assembly bolt
(a) : 8 N·m (0.8 kg-m, 6.0 lb-ft)
Grease 99000-25030 NOTE:
C1 and B0 accumulator pistons are the same.
NOTE:
 Make sure that snap rings are fitted to the groove of
each cylinder.
 Make sure that O-rings are not twisted or caught when
installing.
NOTE:
Make sure that O-rings are not twisted or caught when
installing.
1. C1 accumulator piston 9. C0 accumulator spring
(with Pink paint)
2. C1 accumulator outer spring
(with Yellow paint)10. B1 accumulator piston
3. C1 accumulator inner spring
(with Yellow paint)11. B1 accumulator spacer
4. Spacer 12. B1 accumulator inner spring
(with Orange paint)
5. Snap ring 13. B1 accumulator outer spring
(with Orange paint)
6. B0 accumulator piston 14. C2 accumulator piston
7. B0 accumulator spring
(with Purple paint)15. C2 accumulator inner spring
(with Light Blue paint)
8. C0 accumulator piston 16. C2 accumulator outer spring
(with Light Blue paint)
NOTE:
Apply grease to O-ring of wire-to-solenoid assembly.

7B-132 AUTOMATIC TRANSMISSION (4 A/T)
56) Install valve body assembly (1) to transmission case.
First match the pin of the manual valve to the slot of the
manual shift shaft.
To fix valve body assembly (1) to transmission case, first
tighten bolt B (3), then tighten other bolts.
Tightening torque
Valve body to transmission case bolts
: 10 N·m (1.0 kg-m, 7.5 lb-ft)
57) Connect couplers of wire-to-solenoid to solenoid valves.Bolt Length “a”Pieces
A 30 mm (1.20 in.) 7
B 31 mm (1.22 in.) 2
C 25 mm (0.98 in.) 2
2. Bolt A
4. Bolt C
5. Manual valve pin
6. Slot of manual shift shaft
Solenoid Valve Wire Color
A (No.1) White
B (No.2) Black
C (No.3) Red
D (No.4) Yellow
E (No.5) Brown
TCC (Lock-up) Orange
1. Solenoid valve No.1
2. Solenoid valve No.2
3. Solenoid valve No.3
4. Solenoid valve No.4
5. Solenoid valve No.5
6. Lock-up solenoid

AUTOMATIC TRANSMISSION (4 A/T) 7B-133
58) Install O-ring to oil strainer assembly (1). Make sure that O-
ring is not twisted.
59) Install oil strainer assembly to the top of valve body assem-
bly.
Connect transmission temperature sensor (2) coupler.
Fix transmission temperature sensor and oil strainer assem-
bly with bolts.
Tightening torque
Transmission temperature sensor bolt
(a) : 10 N·m (1.0 kg-m, 7.5 lb-ft)
60) Install magnet (1) in oil pan (2).
61) Install gasket to transmission case and install oil pan (1).
Tightening torque
A/T oil pan bolts (a) : 7.5 N·m (0.75 kg-m, 5.5 lb-ft)
62) Install oil cooler (1) and ground cable (2).
Tightening torque
A/T oil cooler bolt (a): 60 N·m (6.0 kg-m, 43.5 lb-ft)
NOTE:
If metal particles are attached to the magnet, clean them
before installing.

7B-134 AUTOMATIC TRANSMISSION (4 A/T)
63) Install vehicle speed sensor (for speedometer) (1), shift
cable bracket (2) and connector clamp bracket (3).
Tightening torque
Vehicle speed sensor bolt
(a) : 5.5 N·m (0.55 kg-m, 4.0 lb-ft)
Shift cable bracket bolts
(b) : 13 N·m (1.3 kg-m, 9.5 lb-ft)
Connector clamp bracket bolt : 8 N·m (0.8 kg-m, 6.0 lb-ft)
64) Install A/T fluid filler tube (2) and level gauge (1).
Tightening torque
A/T fluid filler tube bolt (a) : 19.5 N·m (1.95 kg-m, 14.5 lb-ft)
65) Install output shaft speed sensor (1) and input shaft speed
sensor (2).
Apply grease to O-ring of each sensor.
Tightening torque
Output shaft speed sensor bolt
(a) : 8 N·m (0.8 kg-m, 6.0 lb-ft)
Input shaft speed sensor bolt
(b) : 8 N·m (0.8 kg-m, 6.0 Ib-ft)
Grease : 99000-25030
66) Install engine mounting LH bracket.
Tightening torque
Engine mounting LH bracket bolts
(a) : 55 N·m (5.5 kg-m, 40.0 lb-ft)

AUTOMATIC TRANSMISSION (4 A/T) 7B-135
67) Install breather sensor hose (1).
68) Install transmission range sensor (2).
Install it temporarily so that the adjustment can be done after
installing assembly back to the vehicle.
Tightening torque
Transmission range sensor bolt
(a) : 18 N·m (1.8 kg-m, 13.0 lb-ft)
69) Install torque converter (1) to input shaft.
Install torque converter, using care not to damage oil seal of
oil pump.
After installing torque converter, check to make sure that dis-
tance “a” is within specification.
Torque converter installing position
“a” : More than 19.9 mm (0.783 in.)
Check torque converter for smooth rotation.
Apply grease around cup at the center of torque converter.
“C” : Grease 99000-25010
CAUTION:
 Before installing converter, make sure that its pump
hub portion is free from nicks, burrs or damage which
may cause oil seal to leak.
 Be very careful not to drop converter on oil pump gear.
Damage in gear, should it occur, may cause a critical
trouble.
2. Flange nut
3. Torque converter housing
4. Cup