TOYOTA CAMRY 2000 Service Repair Manual

AUTOMATIC TRANSAXLEVALVE BODY ±
AX±78
7. REMOVE BOLTS FROM LOWER VALVE BODY
Remove the 3 bolts from lower valve body.
8. LIFT OFF LOWER VALVE BODY AND PLATE AS
SINGLE UNIT
Hold the plate to the lower valve body and lift off the lower
valve body.
HINT: Be careful that the check balls do not fall out.
9. REMOVE PLATE AND GASKETS
VALVE BODY ASSEMBLY
1. POSITION PLATE AND NEW GASKETS ON LOWER
VALVE BODY
Position the new No.2 gasket, the plate and then the new
No.1 gasket on the lower valve body.
HINT: Since No.1 gasket and No.2 gasket are similar use
the illustration below to discriminate between them.
AX0G9±02

AUTOMATIC TRANSAXLEVALVE BODY ±
AX±79
2. PLACE LOWER VALVE BODY WITH PLATE AND GAS-
KETS ON UPPER VALVE BODY
HINT: Hold the lower valve body, gaskets and plate se-
curely so they do not separate.
Align each bolt hole in the valve bodies with the gaskets
and plate.
3. INSTALL AND FINGER TIGHTEN BOLTS IN LOWER
VALVE BODY TO SECURE UPPER VALVE BODY
Install and finger tighten the 3 bolts.
HINT: Each bolt length (mm, in.) is indicated in the illustra-
tion.
4. INSTALL LOWER VALVE BODY COVER
(a) Install the lower valve body cover over the new gasket.
(b) Install and finger tighten the 10 bolts.
HINT: Each bolt length (mm, in.) is indicated in the illustra-
tion.
5. INSTALL AND FINGER TIGHTEN BOLTS IN UPPER
VALVE BODY
Install and finger tighten the 3 bolts.
HINT: Each bolt length (mm, in.) is indicated in the illustra-
tion.
6. INSTALL SLEEVE STOPPER

AUTOMATIC TRANSAXLEVALVE BODY ±
AX±80
7. INSTALL UPPER VALVE BODY COVER GASKETS,
PLATE AND THROTTLE MODULATOR OIL STRAINER
(a) Position a new gasket and plate and then another new
gasket.
HINT: The gaskets are not identical, but can be installed
in any order.
(b) Install the oil strainer onto the gasket.
8. INSTALL UPPER VALVE BODY COVER
(a) Position the upper valve body cover.
(b) Install and finger tighten the 9 bolts.
HINT: Each bolt length (mm, in.) is indicated in the illustra-
tion.
9. INSTALL SOLENOIDS
(a) Install the new O±rings on the solenoids.
(b) Install the No.1 and No.2 solenoids.
(c) Install and finger tighten the 3 bolts.
HINT: Each bolt length (mm, in.) is indicated in the illustra-
tion.
10. TIGHTEN BOLTS OF UPPER AND LOWER VALVE BO-
DIES
(a) Tighten the 16 bolts in the lower valve body.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Tighten the 12 bolts in the upper valve body.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)

AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±81
UPPER VALVE BODY
COMPONENTS
AX0GA±02

AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±82
VALVE BODY SPRINGS SPECIFICATIONS
HINT: During re±assembly please refer to the spring specifications below to help you to discriminate
between the different springs.
Spring (Color)Free Length / Coil Outer Diameter
mm (in.)Number of Coils
@@
@@
@:
[c A]
Throttle Modulator Spring (None)21.70 / 9.50 (0.8543 / 0.3740)9.5
@@
@@
@:
[c B]
Accumulator Control Spring (Yellow)28.06 / 10.60 (1.1047 / 0.4173)13.0
@@
@@
@:
[c C]
Low Coast Modulator Spring (None)21.60 / 7.90 (0.8504 / 0.3110)11.5
@@
@@
@:
[c D]
Down Shift Valve Spring (Yellow)29.76 / 8.73 (1.1717 / 0.3437)13.5
AX0GB±02

AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±83
@@
@@
@:
[c E]
Throttle Valve Spring (None)30.70 / 9.20 (1.2087 / 0.3622)9.5
@@
@@
@:
[c F]
Second Coast Modulator Valve Spring
(Light Green)20.93 / 8.50 (0.8240 / 0.3364)10.0
@@
@@
@:
[c G]
Lock±up Relay Valve spring (Green)26.56 / 10.20 (1.0457 / 0.4016)11.5
@@
@@
@:
[c H]
Cut±back Valve Spring (None)21.80 / 6.00 (0.8583 / 0.2362)13.5

AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±84
RETAINERS, PINS, VIBRATING STOPPER AND CHECK BALLS LOCATION
RetainerHeight / Width / Thickness
mm (in.)
@@@@@: [c H]Throttle Modulator Valve9.2 / 5.0 / 3.2 (0.362 / 0.197 / 0.126)
@@@@@: [c I]Accumulator Control Valve11.5 / 5.0 / 3.2 (0.453 / 0.197 / 0.126)
@@@@@: [c J]Cut±back Valve9.2 / 5.0 / 3.2 (0.362 / 0.197 / 0.126)
@@@@@: [c K]Lock±up Relay Valve15.0 / 5.0 / 3.2 (0.591 / 0.197 / 0.126)
@@@@@: [c L]2nd Coast Modulator Valve15.0 / 5.0 / 3.2 (0.591 / 0.197 / 0.126)
AX0GC±02

AUTOMATIC TRANSAXLELOWER VALVE BODY ±
AX±85
LOWER VALVE BODY
COMPONENTS
AX0GV±02

AUTOMATIC TRANSAXLELOWER VALVE BODY ±
AX±86
VALVE BODY SPRINGS SPECIFICATIONS
HINT: During re±assembly please refer to the spring specifications below to help you to discriminate
between the different springs.
Spring (Color)Free length / Outer diameter
mm (in.)Number of Coils
@@
@@
@:
[c A]
Secondary Regulator Valve Spring
(None)43.60 / 10.90 (1.7165 / 0.4291)11.5
@@
@@
@:
[c B]
Lock±up Signal Valve Spring (None)30.00 / 8.20 (1.1811 / 0.3228)11.5
@@
@@
@:
[c C]
3±4 Shift Valve Spring (None)29.27 / 9.70 (1.1524 / 0.3819)10.5
AX0GD±02

AUTOMATIC TRANSAXLELOWER VALVE BODY ±
AX±87
@@
@@
@:
[c D]
1±2 Shift Valve Spring (None)29.27 / 9.70 (1.1524 / 0.3819)10.5
@@
@@
@:
[c E]
2±3 Shift Valve Spring (None)29.27 / 9.70 (1.1524 / 0.3819)10.5
@@
@@
@:
[c F]
Primary Regulator Valve Spring (None)66.65 / 18.60 (2.6240 / 0.7323)12.5
@@
@@
@:
[c G]
Cooler By±pass Valve Spring (None)19.90 / 11.00 (0.7835 / 0.4331)8.5
@@
@@
@:
[c H]
Pressure Relief Valve Spring (None)11.20 / 6.40 (0.4409 / 0.2520)7.5