service TOYOTA CAMRY V20 1986 Service Information

3. REMOVE REAR VIEW MIRROR
(a) (Manual type)
Remove the setting screw and knob.
(b) Using a screwdriver, pry loose the retainer and re-
move the cover.
HINT: Tape the screwdriver tip before use.
(c) (Electrical type)
Disconnect the connector.
(d) Remove the three screws±and mirror.
(c) Insert a screwdriver between the retainers and door
trim to pry it loose.
HINT: Tape the screwdriver tip before use.
(d) (w/ Power Window and Power Door Lock)
Disconnect the connectors.
5. REMOVE SERVICE HOLE COVER
6. REMOVE OPENING CONTROL LINK FROM DOOR
LOCK
DISASSEMBLY OF FRONT DOOR
1. REMOVE REGULATOR HANDLE
(w/o POWER WINDOW)
Pull oft the snap ring with a cloth and remove the regulator
handle and plate.
2. REMOVE DOOR INSIDE HANDLE
(a) Remove the screw, and slide the handle forward.
(b) Disconnect the handle from the control link and re-
move the handle.
4. REMOVE DOOR TRIM
(a) Remove the two screws from the armrest.
(b) Remove the two caps and two screws.
± BODYFront DoorBO±5

7. REMOVE DOOR GLASS
(a) Wind the glass down into the door cavity.
(b) Remove the two glass channel mounting nuts.
8. REMOVE WINDOW REGULATOR
(a) (w/ Power Window)
Disconnect the connector.
(b) Remove the regulator mounting bolts.
(e) Remove the equalizer arm bracket mounting bolts.
10. REMOVE REAR LOWER FRAME
11. REMOVE FRONT LOWER FRAME
Remove the two bolts from the panel. (d) Remove the regulator through the service hole.
9. REMOVE DOOR GLASS RUN(c) Remove the door glass by pulling it upward.
± BODYFront DoorBO±6

3. INSTALL DOOR LOCK
(a) (w/ Power Door Lock)
Install the door lock solenoid to the door lock with the
screw.
(b) InstalI the door lock with the three screws.
(e) Install the links to the door outside handle and door
lock cylinder. 2. INSTALL DOOR OUTSIDE HANDLE AND DOOR LOCK
CYLINDER
(a) Install the door outside handle with the two bolts.
(b) Install the door lock cylinder with the clip.
4. INSTALL FRONT DOOR BELT MOULDING
(a) Insert the claw of the clips into the upper panel hole
and push the front door belt moulding onto the panel.
(b) Install the screw.
7. INSTALL WINDOW REGULATOR
Place the regulator through the service hole and install the
five mounting bolts. 5. INSTALL FRONT LOWER FRAME
Install the front lower frame with the two bolts.
6. INSTALL REAR LOWER FRAME
± BODYFront DoorBO±8

(b) With the door glass fully closed, .adjust the door glass
stopper so it lightly makes contact with the glass
plate.
11. INSTALL OPENING CONTROL LINK
12. INSTALL SERVICE HOLE COVER
13. INSTALL DOOR TRIM8. INSTALL DOOR GLASS
(a) Place the glass in the door cavity.
(b) Install the glass to the regulator with the two mount-
ing nuts.
9. INSTALL DOOR GLASS RUN
14. INSTALL REAR VIEW MIRROR
(a) Install the mirror with the three screws.
(b) (Electrical type)
Connect the connector.
(c) Install the cover.
(d) (Manual type)
Install the knob with the setting screw.
15. INSTALL DOOR INSIDE HANDLE
(a) Connect the handle to the control link.
(b) Install the handle, slide it rearward, and install the
screw. 10. ADJUST DOOR GLASS
(a) Adjust the equalizer arm up or down and tighten it
where dimensions A and6, as shown, are equal.
± BODYFront DoorBO±9

(b) Insert a screwdriver between the trim retainers and
the door panel to pry it loose.
HINT: Tape the screwdriver tip before use.
4. REMOVE SERVICE HOLE COVER
5. REMOVE DOOR GLASS RUN
DISASSEMBLY OF REAR DOOR
1. REMOVE REGULATOR HANDLE
(w/o POWER WINDOW)
Pull oft the snap ring with a cloth and remove the regulator
handle and plate.
6. REMOVE DIVISION BAR
(a) Remove the two screws under the weatherstrip.
(b) Remove the bolt.
(c) Pull out the division bar. 2. REMOVE DOOR INSIDE HANDLE
(a) Remove the screw, and slide the handle forward.
(b) Disconnect the control link and remove the handle.
3. REMOVE DOOR TRIM WITH INNER WEATHERSTRIP
(a) Remove the two screws from the armrest.
± BODYRear DoorBO±12

8. REMOVE WINDOW REGULATOR
(a) (w/ Power Window)
Disconnect the connector.
(b) Remove the regulator ±mounting bolts.
(c) Remove the equalizer arm bracket mounting bolts. 7. REMOVE DOOR GLASS
(a) Wind the glass down into the door cavity.
(b) Remove the two glass channel mounting nuts.
9. REMOVE REAR DOOR BELT MOULDING
Pry out the rear door belt moulding with the clip as shown.(c) Remove the door glass by pulling it upward.
(d) Remove the regulator through the service hole.
± BODYRear DoorBO±13

7. INSTALL WINDOW REGULATOR
(a) Place the regulator through the service hole.
(b) Install the five mounting bolts.
(c) (w/ Power Window)
Connect the connector. 6. INSTALL REAR DOOR BELT MOULDING
Insert the claw of the clips into the upper panel hole and
push the rear door belt moulding onto the panel.
8. PLACE DOOR GLASS IN DOOR
(a) Insert the door glass in the door cavity.
(b) Install the regulator into the door glass rail.
(c) Install the two glass channel mounting nuts.
9. ADJUST DOOR GLASS
Adjust the equalizer arm up or down and tighten it where
dimension A and6, as shown, are equal.
(b) With the door glass fully closed, adjust the door
glass, stopper so it lightly makes contact with the
glass plate.
± BODYRear DoorBO±16

10. INSTALL DIVISION BAR
(a) Place the division bar in the door.
(b) Install the two screws and bolt.
11. INSTALL DOOR GLASS RUN
12. INSTALL SERVICE HOLE COVER
13. INSTALL DOOR TRIM WITH INNER WEATHERSTRIP
14. INSTALL DOOR INSIDE HANDLE
(a) Connect the handle to the control link.
(b) Install the handle, slide it rearward, and install the
screw.
15. INSTALL REGULATOR HANDLE
With the door window fully closed, install the plate and
regulator handle with the snap ring as shown.
± BODYRear DoorBO±17

HINT:
wRefer to 0/M for operation details of ANTI±THEFT SYSTEM.
wWhen the ID number has been cancelled, reset the same number after completing the operation, or in-
form the customer that it has been cancelled.ANTI±THEFT SYSTEM
operating condition.
(ID number input error 5
times) Take to designated
radio service station. While holding the 1, 4 and6
buttons in. Push and hold the
ºPVIIR VOLº knob. Check
display.
ANTI±THEFT SYSTEM
operating condition.
(ID number input error 4
times or less)
ANTI±THEFT SYSTEM not cancelled. ID number input 5 times or more?
Troubleshooting for ANTI±THEFT SYSTEM
Turn ignition key from LOCK position to ACC position.
ANTI±THEFT SYSTEM cancelled.
Check audio system again.
(Liquid Crystal Display (LCD) for Audio System)Cancel ID number, refer to each malfunction item.Cancel ID number, refer to each malfunction
item. Normal operation when radio
switch turned ON?
Take to designated radio service station.Refer to each malfunction
item.
ºSECº display disappears
after 1 second.ID number not input.
(Display D)
ID number not
input, or else
input error. After 2 seconds
Display C ± A Input ID number, check display.Forgot to press switch. Radio switch turned 4N. Display A showing?
Display B showing? ID nubmer is set.
Display A or BDisplay
EDisplay
B
Display DYe s
Ye sYe s Ye s
Ye s
± BODY ELECTRICAL SYSTEMAudio SystemBE±94

ANTI±LOCK BRAKE SYSTEM (A.B.S.)
Description
wThe A.B.S. is a brake system which controls the wheel cylinder hydraulic pressure of all four wheels during
sudden braking and braking on slippery road surfaces, preventing the wheels from locking. This A.B.S.
provides the following benefits:
(1) Enables steering round an obstacle with a greater degree of certainty even when panic braking.
(2) Enables stopping in a panic brake while keeping the effect upon stability and steerability to a mini-
mum, even on curves.
wThe function of the A.B.S. is to help maintain directional stability and vehicle steerability on most road
conditions. However, the system cannot prevent the vehicle from skidding if the cornering speed limit is
exceeded.
wThe A.B.S. has a longitudinal deceleration sensor to match braking characteristics to the full±time four±
wheel drive. (For 4WD)
wIn case a malfunction occurs, a diagnosis function and fail±safe system have been adopted for the A.B.S.
to increase serviceability.
2WD (SEDAN)
± BRAKE SYSTEMAnti±lock Brake System (A.B.S.)BR±56