ABS TOYOTA CAMRY V20 1986 Service Information

Stabilizer Bar
(See page RA±50)
REMOVAL OF STABILIZER BAR
1. DISCONNECT STABILIZER LINK FROM SHOCK
ABSORBER
3. REMOVE STABILIZER BAR BRACKET
(a) Remove the four bolts.
(b) Remove the stabilizer bar brackets and cushions from
the stabilizer bar.
4. DISCONNECT TANK BAND FROM BODY
(a) Using a jack and wooden block, support the fuel tank.
(b) Remove the two tank and installation bolts.
5. REMOVE STABILIZER BAR
Lower the fuel tank about 40 mm (1.57 in.) and then
remove the stabilizer bar from the body. 2. REMOVE STABILIZER BAR LINK FROM STABILIZER
BAR
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±60

2. PLACE STABILIZER BAR
3. CONNECT TANK BAND TO BODY
Position the fuel tank in position, connect the tank
bands to the body and torque the installation bolts.
Torque: 400 kg±cm (29 ft±Ib, 39 N±m )
INSTALLATION OF STABILIZER BAR
1. INSPECT STABILIZER LINK
Move the ball joint stud in all directions, if the movement is
not smooth and free, replace the stabilizer link.
4. INSTALL STABILIZER BAR TO BODY
(a) Install the cushion and brackets to the stabilizer bar.
(b) Torque the four bolts.
Torque: 195 kg±cm (14 ft±Ib, 19 N±m)
6. CONNECT STABILIZER LINK TO SHOCK ABSORBER
Torque: 650 kg±cm (47 ft±Ib, 64 N±m)
5. INSTALL STABILIZER LINK TO STABILIZER BAR
Torque: 650 kg±cm (47 ft±Ib, 64 N± m)
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±61

Tie rod end lock nut
Shock absorber X Steering knuckle Tie rod end x Steering knuckle
Ball joint x Lower suspension arm
Disc brake caliper X Steering knuckle
Hub bearing lock nut
Center drive shaft bearing lock nut
Ball joint x Steering knuckle
Drive shaft x Side gear shaft (FWD/VZV21 and 4WD)
Drive shaft x Center drive shaft (FWD/VZV21) ,
Center drive shaft bearing bracket installation bolt
(FWD 1)
Drive shaft bearing bracket bolt (GKN)
(TOYOTA)
Drive shaft bearing bracket x Bracket stay
Piston rod x Suspension support
Suspension support x Body
Disc brake hose union bolt
Suspension lower crossmember x Body
Stabilizer bar x Lower suspension arm
Lower arm shaft x Lower suspension arm
Lower arm shaft x Body
Stabilizer bar bracket x Body
Engine center mounting member X Body
Engine center mounting member x Engine mountings
Torque Specifications
Part tightened
± SERVICE SPECIFICATIONSFront Axle and SuspensionA±32

Axle bearing lock nut
Axle carrier x Shock Absorber
Axle hub x Axle carrier
Strut rod X Axle carrier
No. 1 and No. 2 suspension arm x Axle carrier
Drive shaft x 'Side gear shaft
Piston rod X Suspension support
Suspension support x Body
No. 1 suspension Arm x Body
No. 2 suspension arm x Body
Strut rod X Body
Stabilizer bar X Stabilizer bar link
Shock absorber X Stabilizer bar link
Stabilizer bar bracket x Body
Fuel tank band X Body
Hub nut
Carrier x Carrier cover
Carrier X Drain plug
Carrier x Filler plug
Carrier x Side bearing cap
Ring gear x Differential case
Drive pinion x Companion flage
Companion flange x Propeller shaft (4WD)
Differential x Support member
Torque Specifications
Part tightened
± SERVICE SPECIFICATIONSRear Axle and SuspensionA±35

SST (SPECIAL SERVICE TOOLS) (Cont'd)
Shock Absorber
Overhaul Tool Set
Front Shock Absorber
Ring Nut Wrench
Lower Suspension
Arm Bushing
Remover & Replacer
(Spacer)
Brake Tube Union
Nut 10x12mm
Wrench
Luggage Compart±
ment Door Torsion
Bar ToolBrake Shoe Return
Spring Reptarcer
Front Spring Upper
Seat Holder
Remark:
* 1 Drive shaft Shoe Hold Down
Spring Driver
Brake Booster
Push Rod GaugeCoil Spring
Compressor
Coil Spring
Compressor
Part Name
Illustration Section
Part No.
RA
SR
± SST AND SSMSST (Special Service ToolsC±18