light TOYOTA CAMRY V20 1986 Service Information

3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are ad-
justed correctly.
(b) Adjust the striker position by slightly loosening the
striker mounting screws, and hitting the striker with a
hammer.
Tighten the striker mounting screws again.
ADJUSTMENT OF FRONT DOOR
1. ADJUST DOOR IN FORWARD/REARWARD AND
VERTICAL DIRECTIONS
Using SST, adjust the door by loosening the body side
hinge bolts.
SST 09812±00010 16. INSTALL REGULATOR HANDLE
With door window fully closed, install the plate and regula-
tor handle with a snap ring as shown.
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
± BODYBO±10

7. INSTALL WINDOW REGULATOR
(a) Place the regulator through the service hole.
(b) Install the five mounting bolts.
(c) (w/ Power Window)
Connect the connector. 6. INSTALL REAR DOOR BELT MOULDING
Insert the claw of the clips into the upper panel hole and
push the rear door belt moulding onto the panel.
8. PLACE DOOR GLASS IN DOOR
(a) Insert the door glass in the door cavity.
(b) Install the regulator into the door glass rail.
(c) Install the two glass channel mounting nuts.
9. ADJUST DOOR GLASS
Adjust the equalizer arm up or down and tighten it where
dimension A and6, as shown, are equal.
(b) With the door glass fully closed, adjust the door
glass, stopper so it lightly makes contact with the
glass plate.
± BODYRear DoorBO±16

3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and lock linkages are adjusted
correctly.
(b) Adjust the striker position by slightly loosening the
striker mounting screws, and hitting the striker with a
hammer.
Tighten the striker mounting screws again.
ADJUSTMENT OF REAR DOOR
1. ADJUST DOOR IN FORWARD/ REARWARD AND
VERTICAL DIRECTIONS
Using a wrench, loosen the body side hinge bolts.
2. ADJUST DOOR IN LEFT/RIGHTAND VERTICAL
DIRECTIONS
Using a wrench, loosen the door side hinge bolts.
± BODYRear DoorBO±18

3. REMOVE DOOR LOCK CONTROL
(a) Remove the link protector.
(b) Disconnect the links from the door lock control and
door lock cylinder.
(c) Disconnect the connector from the solenoid.
(d) Remove the four bolts and door lock control with the
solenoid.
DISASSEMBLY OF BACK DOOR
1. REMOVE UPPER AND LOWER DOOR TRIMS
(a) Remove the six clips.
(b) Insert a screwdriver between the trim retainers and
door panel to pry it loose.
HINT: Tape the screwdriver tip before use.
2. REMOVE HIGH MOUNT STOP LIGHT
(a) Disconnect the connector from the high mount stop
light.
(b) Remove the two bolts and high mount stop light.
4. REMOVE DOOR LOCK CYLINDER
Remove the two screws and door lock cylinder.
5. REMOVE LOWER MOULDING
(See page 80±36)
6. REMOVE COMBINATION LIGHT
(a) Disconnect the connector from the combination light.
(b) Remove the eight nuts and combination light.
± BODYBack DoorBO±22

Precautions for storing moulding material:
wStore in a cool place, avoiding direct sunlight, high
temperatures and dust.
wThe moulding is of polyvinyl chloride, so do not allow it to
come in contact with thinner or other solvent, open flame,
or boiling water.
wThe storage time for the moulding, adhesive and Primer T
is limited to about 9 months.
REMOVAL OF FRONT FENDER FRONT
SIDE AND QUARTER SIDE MOULDING
REMOVE MOULDING
(a) Remove the nut from the moulding. (Front fender
front side)
(b) Using a scraper, pry loose the clips and remove the
moulding.
HINT: Apply tape to the scraper blade to prevent scratch±
ing the vehicle body.
INSTALLATION OF FRONT FENDER
FRONT SIDE AND QUARTER SIDE
MOULDING
1. CLEAN MOULDING MOUNTING SURFACE
Wipe oft with a rag.
2. INSTALL MOULDING
(a) Install the clips to the moulding and push the mould-
ing onto the panel by hand.
(b) Install the nut to the moulding. (Front fender front
side)
REMOVAL OF FRONT FENDER REAR
SIDE AND DOOR SIDE MOULDING
1. REMOVE ENDS OF MOULDING
Using a scraper, pry the moulding loose about 30 mm
(1.18 in.) from the ends.
HINT: Apply tape to the scraper blade to prevent scratch-
ing the vehicle body.
Side Body Moulding
TOOLS AND SUPPLIES
Cleaner (for cleaning body and removing body oil stains)
Heat lightAdhesive (Super special) 20g (0±71 oz.)
08850±00051
Quantity
Part name Part No.
± BODYMouldingBO±30

4. APPLY ADHESIVE TO MOULDING
Apply adhesive to both punched out ends of the double±
stick tape.
NOTICE: Install the moulding within 7 minutes after applying
the adhesive.
5. LIFT MOULDING RELEASE SHEET FROM FACE OF
MOULDING
NOTICE: When the moulding release sheet is removed, be
sure that no dirt or dust can get onto the uncovered
area.
2. REMOVE MOULDING AND ADHESIVE
(a) Pull off the moulding by cutting the adhesive with a
knife.
(b) Scrape. off adhesive from the body with a cutter or
sandpaper.
NOTICE:
w30 ± 80 mm (1.18 ± 3.15 in.) of the ends of the moulding
are glued tightly with a strong adhesive.
wDo not reuse moulding.
2. HEAT MOUNTING SURFACE
Using a heat tight, heat the mounting surface to 40 ± 60
°C (104 ± 140°F).
NOTICE: When the moulding is installed, the tem±
perature of the mounting surface should be 20°C (68°F)
of higher.
3. HEAT MOULDING
Using a heat light, heat the moulding to 30 60
°C (86 ±
140°F).
NOTICE: Do not heat moulding excessively. The tempera-
ture should not be higher than 80°C (176°F).
INSTALLATION OF FRONT FENDER
REAR SIDE AND DOOR SIDE
MOULDING
1. CLEAN MOULDING MOUNTING SURFACE
Wipe off stains with cleaner.
± BODYMouldingBO±31

REMOVAL OF REAR WINDOW GLASS
1. DISCONNECT DEFOGGER WIRE CONNECTORS
2. REMOVE REAR SEAT BELT ANCHOR BOLT
3. REMOVE ROOF SIDE INNER GARNISH
(See page BO±44)
4. REMOVE REAR MOULDING AND CLIPS
(See page BO±33)
5. REMOVE HIGH MOUNT STOP LIGHT
(a) Remove the high mount stop light cover.
(b) Disconnect the connector from the high mount stop
light.
(c) Remove the two bolts and high mount stop light.
6. REMOVE CRS TETHER ANCHOR
Remove the bolt with CRS tether anchor.
7. REMOVE PACKAGE TRAY TRIM
REAR WINDOW GLASS
PREPARE ITEMS LISTED
(See page BO±37)
COMPONENTS
± BODYRear Window GlassBO±49

PREPARATION FOR INSTALLATION
(See pages BO±40 and 41)
INSTALLATION OF REAR WINDOW
GLASS
1. INSTALL DAM
(See page BO±41)
HINT: Install the dam on the surroundings of glass.
2. COAT CONTACT SURFACE OF BODY WITH PRIMER
ªMº
(See page BO±41)
3. COAT CONTACT SURFACE OF GLASS WITH PRIMER
ªGº
(See page BO±41)
4. MIX ADHESIVE COATING
(See page BO±41)
5. APPLY ADHESIVE
(See page BO±41)
6. INSTALL GLASS
(See page BO±42)
7. INSPECT FOR LEAKS AND REPAIR
(See page BO±42)
8. INSTALL REAR MOULDING AND CLIPS
(See page 80±34)
9. INSTALL HIGH MOUNT STOP LIGHT
(a) Install the high mount stop light with the two bolts.
(b) Connect the connector to the high mount stop light.
(c) Install the high mount stop light cover.
10. INSTALL PACKAGE TRAY TRIM
11. INSTALL CRS TETHER ANCHOR
Install the CRS tether anchor with the bolt.
Torque: 210 kg±cm (15 ft±Ib, 21 N±m)
12. INSTALL ROOF SIDE INNER GARNISH
13. INSTALL REAR SEAT BELT ANCHOR BOLT
Torque: 440 kg±cm (32 ft±Ib, 43 N±m)
14. CONNECT DEFOGGER WIRE CONNECTORS8. REMOVE REAR WINDOW GLASS
HINT: Remove the rear window glass in the same manner
as the windshield glass. (See page BO±39)
± BODYRear Window GlassBO±50

REMOVAL OF BACK DOOR GLASS
1. REMOVE REAR WIPER ARM
2. DISCONNECT DEFOGGER WIRE CONNECTORS
3. REMOVE BACK DOOR UPPER TRIM
4. REMOVE HIGH MOUNT STOP LIGHT
(a) Disconnect the connector from the high mount stop
light.
(b) Remove the two bolts and high mount stop light.
BACK DOOR GLASS
PREPARE ITEMS LISTED
(See page BO±37)
COMPONENTS
± BODYBack Door GlassBO±51

PREPARATION FOR INSTALLATION
(See pages BO±40 and 41)
INSTALLATION OF BACK DOOR
GLASS
1. INSTALL DAM
(See page BO±41)
HINT: Install the dam on the surroundings of glass.
2. COAT CONTACT SURFACE OF BODY WITH PRIMER
ªMº
(See page BO±41)
3. COAT CONTACT SURFACE OF GLASS WITH PRIMER
ªGº
(See page BO±41)
4. MIX ADHESIVE COATING
(See page BO±41)
5. APPLY .ADHESIVE
(See page BO±41)
6. INSTALL GLASS
(See page BO±42)
7. INSPECT FOR LEAKS AND REPAIR
(See page BO±42)
8. INSTALL UPPER MOULDING
HINT: Install the upper moulding in the same manner as
the windshield upper moulding. (See page BO±26)
9. INSTALL LOWER MOULDING WITH CLIPS
(See page BO±36) 5. REMOVE LOWER MOULDING AND CLIPS
(See page BO±36)
6. REMOVE UPPER MOULDING
HINT: Remove the upper moulding in the same manner as
the windshield upper moulding. (See page BO±26)
7. REMOVE BACK DOOR GLASS
HINT: Remove the back door glass in the same manner
as the windshield glass. (See page BO±39)
10. INSTALL HIGH MOUNT STOP LIGHT
Install the high mount stop light with the two bolts.
(b) Connect the connector to the high mount stop light.
11. INSTALL BACK DOOR UPPER TRIM
12. CONNECT DEFOGGER WIRE CONNECTORS
13. INSTALL REAR WIPER ARM
± BODYBack Door GlassBO±52