width TOYOTA HILUX 2023 Owners Manual

2914-5. Using the driving support systems
4
Driving
HILUX_OM_OM0K789E_(EE)
■Operation conditions of each function
● Lane departure alert function
This function operates when all of the following conditions are met.
• LDA is turned on.
• Vehicle speed is approximately 50 km/h (32 mph) or more.
• System recognizes white (yellow) lane lines or a course*. (When a
white [yellow] line or course* is recognized on only one side, the system
will operate only for the recognized side.)
• Width of traffic lane is approximately 3 m (9.8 ft.) or more.
• Turn signal lever is not operated.
• Vehicle is not being driven around a sharp curve.
• No system malfunctions are detected. ( P. 293)
*: Boundary between asphalt and the side of the road, such as grass, soil,
or a curb
● Yaw assist function
This function operates when all of the following conditions are met in addi-
tion to the operation conditions fo r the lane departure alert function.
• Setting for “Yaw assist” in of the multi-information display is set
to “On” ( P. 133)
• Vehicle is not accelerated or decelerated by a fixed amount or more.
• Steering wheel is not operated with a steering force level suitable for
changing lanes.
• ABS, VSC, TRC/A-TRC and PCS are not operating.
• TRC/A-TRC or VSC is not turned off.
● Vehicle sway warning function
This function operates when all of the following conditions are met.
• Setting for “Sway Warning” in of the multi-information display is
set to “On” ( P. 1 3 3 )
• Vehicle speed is approximately 50 km/h (32 mph) or more.
• Width of traffic lane is approximately 3 m (9.8 ft.) or more.
• No system malfunctions are detected. ( P. 293)

5127-3. Do-it-yourself maintenance
HILUX_OM_OM0K789E_(EE)
Wheels
When replacing wheels, care should be taken to ensure that they are
equivalent to those removed in load capacity, diameter, rim width and
inset*.
Replacement wheels are available at any authorized Toyota retailer or
Toyota authorized repairer, or any reliable repairer.
*: Conventionally referred to as “offset”.
Toyota does not recommend using the following:
● Wheels of different sizes or types
● Used wheels
● Bent wheels that have been straightened
● Use only Toyota wheel nuts and wrenches designed for use with
your aluminum wheels.
● When rotating, repairing or changing your tires, check that the
wheel nuts are still tight after driving 1600 km (1000 miles).
● Be careful not to damage the aluminum wheels when using tire
chains.
● Use only Toyota genuine balance weights or equivalent and a plas-
tic or rubber hammer when balancing your wheels.
If a wheel is bent, cracked or heavily corroded, it should be
replaced. Otherwise, the tire may separate from the wheel or
cause a loss of handling control.
Wheel selection
Aluminum wheel precautions (if equipped)

6209-1. Specifications
HILUX_OM_OM0K789E_(EE)
Maintenance data (fuel, oil level, etc.)
*1: Unladen vehicle
*2: With tailgate type A (P. 158)
*3: With tailgate type B (P. 158)
*4: Without side step
*5: With side step
Dimensions
Overall
length
Without
over fender
Without rear bumper 5265 mm (207.3 in.)*2
5285 mm (208.1 in.)*3
With rear bumper 5335 mm (210.0 in.)
With
over fender
Without rear bumper 5255 mm (206.9 in.)*2
5275 mm (207.7 in.)*3
With rear bumper 5325 mm (209.6 in.)
Overall
width
Without over fender 1800 mm (70.9 in.)*4
1815 mm (71.5 in.)*5
With over fender
1855 mm (73.0 in.)*6, 15
1900 mm (74.8 in.)*7, 15
1910 mm (75.2 in.)*8, 15
2015 mm (79.3 in.)*16
Overall
height*1
Single-cab models 1855 mm (73.0 in.)*10
1795 mm (70.7 in.)*11
Smart-cab models 1860 mm (73.2 in.)*10
1810 mm (71.3 in.)*11
Double-cab models
1865 mm (73.4 in.)*10, 15
1880 mm (74.0 in.)*10, 16
1815 mm (71.5 in.)*11, 15
1830 mm (72.0 in.)*11, 16
Wheelbase 3090 mm (121.7 in.)
Front tread
1505 mm (59.3 in.)*12
1495 mm (58.9 in.)*13
1535 mm (60.4 in.)*14, 15
1670 mm (65.7 in.)*14, 16
Rear tread
1520 mm (59.8 in.)*12
1510 mm (59.4 in.)*13
1550 mm (61.0 in.)*14, 15
1705 mm (67.1 in.)*14, 16