lock TOYOTA LAND CRUISER 1996 J80 Owners Manual

DI−14
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC No.
(See Page)
Detection ItemTrouble AreaMILMemory
P0171
( DI−51 )System too Lean
(Fuel T rim)
Air intake (hose loose)
 Fuel line pressure, leak
 Injector blockage
 Heated oxygen sensor malfunction
 Mass air flow meter
 Engine coolant temp. sensor
 *1
P0172
( DI−51 )System too Rich
(Fuel T rim)
Fuel line pressure
 Injector leak, blockage
 Heated oxygen sensor malfunction
 Mass air flow meter
 Engine coolant temp. sensor
 *1
P0300
( DI−54 )Random/Multiple Cylinder
Misfire DetectedIgnition system
 Injector
 Fuel line pressure
 EGR
 Compression pressure
 Valve clearance not to specification
 Valve timing
 Mass air flow meter
 Engine coolant temp. sensor
 *2
P0301
P0302
P0303
P0304
P0305
P0306
( DI−54 )Misfire Detected
− Cylinder 1
− Cylinder 2
− Cylinder 3
− Cylinder 4
− Cylinder 5
− Cylinder 6
P0325
( DI−59 )Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
 Knock sensor 1 (looseness)
 ECM
 *1
P0330
( DI−59 )Knock Sensor 2 Circuit
MalfunctionOpen or short in knock sensor 2 circuit
 Knock sensor 2 (looseness)
 ECM
 *1
P0335
( DI−62 )Crankshaft Position Sensor
”A” Circuit Malfunction
Open or short in crankshaft position sensor circuit for NE sig-
nal
 Crankshaft position sensor for NE signal
 Starter
 ECM
 *1
P0340
( DI−65 )Camshaft Position Sensor
Circuit MalfunctionOpen or short in camshaft position sensor circuit
 Camshaft position sensor
 ECM
 *1
P0385
( DI−67 )Crankshaft Position Sensor
”B” Circuit Malfunction
Open or short in crankshaft position sensor circuit for NE2
signal
 Crankshaft position sensor for NE2 signal
 ECM
 *1
P0401
( DI−69 )Exhaust Gas Recirculation
Flow Insufficient Detected
EGR valve stuck closed
 Short in VSV circuit for EGR
 Open in EGR gas temp. sensor circuit
 EGR hose disconnected
 ECM
 *1
P0402
( DI−80 )Exhaust Gas Recirculation
Flow Excessive Detected
EGR valve stuck open
 EGR VSV open malfunction
 Open in VSV circuit for EGR
 Short in EGR gas temp. sensor circuit
 ECM
 *1
*1: MIL lights up
*2: MIL lights up or blinking
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−51
1996 LAND CRUISER (RM451U)
DTC P0171 System too Lean (Fuel Trim)
DTC P0172 System too Rich (Fuel Trim)
CIRCUIT DESCRIPTION
”Fuel trim” refers to the feedback compensation value compared against the basic injection time. Fuel trim
includes short−term fuel trim and long −term fuel trim.
”Short−term fuel trim” is the short−term fuel compensation used to maintain the air −fuel ratio at its ideal
theoretical value. The signal from the heated oxygen sensor indicates whether the a\
ir −fuel ratio is RICH or
LEAN compared to the ideal theoretical value, triggering a reduction in fuel \
volume if the air −fuel ratio is rich,
and an increase in fuel volume if it is lean.
”Long −term fuel trim” is overall fuel compensation carried out long −term to compensate for continual devi-
ation of the short−term fuel trim form the central value due to individual engine differences, wear over time
and changes in the usage environment.
If both the short−term fuel trim and long−term fuel trim are LEAN or RICH beyond a certain value, it is de-
tected as a malfunction and the MIL lights up.
DTC No.DTC Detecting ConditionTrouble Area
P0171
When the air fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the RICH side.
(2 trip detection logic)
 Air intake (hose loose)
 Fuel line pressure
 Injector blockage, leak
 Heated oxygen sensor (bank 1 sensor 1) malfunction
 Mass air flow meter
 Engine coolant temp. sensor
P0172
When the air fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the LEAN side.
(2 trip detection logic)
Fuel line pressure
 Injector blockage, leak
 Heated oxygen sensor (bank 1 sensor 1) malfunction
 Mass air flow meter
 Engine coolant temp. sensor
HINT:
When the DTC P0171 is recorded, the actual air− fuel ratio is on the LEAN side. When DTC P0172 is
recorded, the actual air−fuel ratio is on the RICH side.
If the total of the short −term fuel trim value and long −term fuel trim value is within + 30 − − 35 %, the
system is functioning normally.
If the vehicle runs out of fuel, the air −fuel ratio is LEAN and DTC P0171 is recorded. The MIL then come
on.
INSPECTION PROCEDURE
1 Check air induction system (See page SF−1 ).
NG Repair or replace
OK
DI5PE−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22425
Knock Sensor 1KNK2
Knock Sensor 2 KNK1
ECM
E1
E1
E5
E5
6
14
B
L−W
(On front side)
1
(On rear side) 1
−
DIAGNOSTICS ENGINE
DI−59
1996 LAND CRUISER (RM451U)
DTC P0325 Knock Sensor 1 Circuit Malfunction
DTC P0330 Knock Sensor 2 Circuit Malfunction
CIRCUIT DESCRIPTION
Knock sensors are fitted one each to the front and rear of the left side of t\
he cylinder block to detect engine
knocking. This sensor contains a piezoelectric element which generates a voltage \
when it becomes de-
formed, which occurs when the cylinder block vibrates due to knocking. If engin\
e knocking occurs, ignition
timing is retarded to suppress it.
DTC No.DTC Detecting ConditionTrouble Area
P0325No knock sensor 1 signal to ECM with engine speed, between
1,800 rpm and 5.200 rpmOpen or short in knock sensor 1 circuit
 Knock sensor 1 (looseness)
 ECM
P0330No knock sensor 2 signal to ECM with engine speed, between
1,800 rpm and 5.200 rpmOpen or short in knock sensor 2 circuit
 Knock sensor 2 (looseness)
 ECM
If the ECM detects the above DTCs, it operates the fail safe function in w\
hich the corrective retard angle value
is set to the maximum value.
WIRING DIAGRAM
DI5PG−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE6053P24676A08534
LOCK
(+)
(−)
BATT
P22346
R/B No.2
EFI Fuse
DI−106
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check voltage between terminal BATT of ECM connector and body ground.
PREPARATION:
Remove the instrument panel speaker No.1 panel
(See page SF−65 ).
CHECK:
Measure voltage between terminal BATT of ECM connector
and body ground.
OK:
Voltage 9 − 14 V
OK Check and replace ECM (See page IN−28 ).
NG
2 Check EFI fuse.
PREPARATION:
Remove EFI fuse from R/B No.2.
CHECK:
Check continuity of EFI fuse.
OK:
Continuity
NG Check for short in all the harness and components connected to EFI fuse.
OK
Check and repair harness or connector
between battery, EFI fuse and ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22478
Battery
FL AM1
Fusible Link
1F6
B−L
2
2 2
2
3
4
AM1
R/B No.2
Junction
Connector (J4)
Y Y
IG Switch
4 2
1 B−W
B−YFuse Block
GAUGE
Y
B
B 6IH14
B−W Park/Neutral
Position Switch
3
2 G−R G−W
O
O
IH2
To A/T Indicator Light
(Combination Meter)
Starter
1
S1 E7
E7
E7
17
16
22 NSW
E1B+
E1 E1
L
2 ECM
W
EA26
B
B
B−R
65 3
2IH1
21
B−W
IH2
DI−108
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P1780 Park/Neutral Position Switch Malfunction
CIRCUIT DESCRIPTION
The park/neutral position switch goes on when the shift lever is in the N o\
r P shift position. When it goes on
terminal NSW of the ECM is grounded to body ground via the starter relay, thus the terminal NSW voltage
becomes 0 V. When the shift lever is in the D, 2, L or R position, the park/neutral\
position switch goes off,
so the voltage of ECM, terminal NSW becomes battery voltage, the voltage of the ECM internal power
source. If the shift lever is moved from the N position to the D position, this signal is used for air\
−fuel ratio
correction and for idle speed control (estimated control), etc.
DTC No.DTC Detecting ConditionTrouble Area
P1780
2 or more switches are ON simultaneously for ”N”, ”2” and ”\
L”
position (2 trip detection logic)
 Short in park/neutral position switch circuit
 Park/neutral position switch
 ECMWhen driving under conditions (a) and (b) for 30 sec. or more
the park/neutral position switch is ON (N position):
(2 trip detection logic)
(a) Vehicle speed: 70 km/h (44 mph) or more
(b) Engine speed: 1,500 − 2,500 rpm
HINT:
After confirming DTC P1780 use the T OYOTA hand−held tester to confirm the PNP switch signal from ”CUR-
RENT DATA”.
WIRING DIAGRAM
DI5PV−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

S00816
BatteryFusible
Link
F8F7
11
W−R
3EA2
W−R11 6
IG Switch B−R
Fuse BlockIGN B−L
22
22 2
2
EFI Main Relay
1
2
3 4
EFI R
−Y
EC
EB
B−R
1EB1
R
Y−R
Y−REA2IH1
22 7
BR−B E4
E7 E7 E7
IGSW
MRLY
+B
E1 B+
ECM
1
3
12
24FL AM2
FL MAIN
W R
R/B No.2 Y
DI−11 0
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
ECM Power Source Circuit
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, battery positive voltage is applied t\
o the coil, closing the contacts of
the EFI main relay (Marking: EFI) and supplying power to the terminals +B\
of the ECM.
WIRING DIAGRAM
DI5PX−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24681
DI−11 2
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check IGN fuse from fuse block.
NG Check for short in all the harness and
components connected to IGN fuse.
OK
5 Check ignition switch.
PREPARATION:
(a) Remove instrument lower finish panel.
(b) Remove instrument cluster finish center panel No.2.
CHECK:
Check continuity between terminals.
OK:
Shift PositionTerminal No. to continuityTerminal No. to continuity
LOCK−−
ACC3 − 4−
ON2 − 3 − 46 − 11
START1 − 2 − 45 − 6 − 11
NG Replace ignition switch.
OK
Check for open and short in harness and
connector between battery and ignition
switch and ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

S02978
Battery
FL MAINFL AM2
F7E81
1
EA23
W−R W−R
W
2
22
2 2
2
EFI Main Relay
1 2 3 4
R−Y
Y−R
Y−R
EB1
IH1
22Y R
2
1 4
3
IG Switch 6
11
B−R B−LCircuit
Opening
Relay
Fuse Block R−G
R−W 5
Fuel Pump
Relay
123
1
2
Fuel Pump
Resister
R−B
R−B
ID2
BO1
13
3
36 Fuel Pump W−B
5
BO1
W−B
W−RR−W
IH1
17
E7
E7
E4 3
13
14
MRLYR
FC
FPR B+
E01
E01
ECM
BF
EA2
7
Fusible
LinkFEI
EB
R−G
R−W
R−G
1
BR
R/B No.2
IGN
DI−11 6
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00192
ONFC
(+)
(−)
BE6653
P24684
DI−11 8
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check voltage between terminal FC of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal FC of ECM and body
ground.
OK:
Voltage: 9 − 14 V
OK Go to step 5.
NG
Check for open and short in harness and connector between terminal FC of ECM a\
nd circuit open-
ing relay and fuse block (See page IN−28).
4 Connect the TOYOTA hand−held tester and check operation of fuel pump relay.
PREPARATION:
(a) Connect the TOYOTA hand−held tester to the DLC3.
(b) Start the engine.
(c) Turn TOYOTA hand−held tester main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand−held tester.
CHECK:
Check operation of fuel pump relay when it is switched ON and OFF by the\
TOYOTA hand −held tester.
OK:
Operating noise can be heard from the relay.
OK Go to step 8.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−122
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
2 Check circuit opening relay (See page DI−84 ).
NG Replace circuit opening relay.
OK
3 Check voltage between terminal FC of ECM connector and body ground (See\
step 3 of TOYOTA hand −held tester).
OK Go to step 4.
NG
Check for open and short in harness and connector between terminal FC of ECM a\
nd circuit open-
ing relay and fuse block (See page IN−28).
4 Check operation of fuel pump relay (See step 5 of TOYOTA hand −held tester).
NG Replace fuel pump relay.
OK
5 Check voltage between terminal FPR of ECM connector and body ground (Se\
e step 6 of TOYOTA hand −held tester).
NG Check and replace ECM (See page IN−28 ).
6 Check for open and short in harness and connector between terminal FC of\
ECM
connector and fuel pump relay (See page IN−28).
NG Repair or replace harness or connector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010