Electrical TOYOTA LAND CRUISER 1996 J80 Owner's Guide

BE1M5−01
BE−22
−
BODY ELECTRICAL BACK−UP LIGHT SYSTEM
1160
Author: Date:
1996 LAND CRUISER (RM451U)
BACK −UP LIGHT SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M6−01
−
BODY ELECTRICAL BACK−UP LIGHT SYSTEM
BE−23
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT PARK/NEUTRAL POSITION SWITCH CONTINUITY (See page AT−6)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M7−01
BE−24
−
BODY ELECTRICAL STOP LIGHT SYSTEM
1162
Author: Date:
1996 LAND CRUISER (RM451U)
STOP LIGHT SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M8−01
−
BODY ELECTRICAL STOP LIGHT SYSTEM
BE−25
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT STOP LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
SW pin free1 − 2Continuity
SW pin pushed in−No continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M9−01
BE−26
−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
1164
Author: Date:
1996 LAND CRUISER (RM451U)
WIPER AND WASHER SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MA−01
B7B16
B18
B7 B4
B18 B16
−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
BE−27
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT FRONT WIPER AND WASHER SWITCH
CONTINUITY
Switch positionTester connectionSpecified condition
Wiper OFFB4 − B7Continuity
Wiper INTB4 − B7Continuity
Wiper LOB7 − B18Continuity
Wiper HIB13 − B18Continuity
Washer OFF−No continuity
Washer ONB8 − B16Continuity
If continuity is not as specified, replace the switch.
2. INSPECT REAR WIPER AND WASHER SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
Washer ONB2 − B16Continuity
Wiper OFF−No continuity
Wiper INTB10 − B16Continuity
Wiper ONB1 − B16Continuity
Washer ONB1 − B2 − B16Continuity
If continuity is not as specified, replace the switch.
3. INSPECT INTERMITTENT WIPER OPERATION
(a) Turn the wiper switch to INT position.
(b) Turn the intermitte nt time control switch to FAST position.
(c) Connect the positive (+) lead from the battery to terminal
B18 and the negative ( −) lead to terminal B16.
(d) Connect the positive (+) lead from the voltmeter to termi- nal B7 and the negative ( −) lead to terminal B16, and
check that the meter needle indicates battery positive
voltage.
(e) After connecting terminal B4 to termianl B18, connect B18 to terminal B16.
Then, check that the voltage rises from O volt to battery
positive voltage within time as follows.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

V02744
3.3 ± 1 sec.
Battery Positive Voltage
B7B16
B18
V02745
Washer Switch ON
OFF Approx.
0.5 sec.
Battery-
positive
voltage Approx. 2.5 sec.
0 V
BE−28
−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
1996 LAND CRUISER (RM451U)
If operation is not as specified, replace the switch.
4. INSPECT WASHER LINKED OPERATION
(a) Connect the positive (+) lead from the battery to terminal
B18 and the negative ( −) lead to terminal B16.
(b) Connect the positive (+) lead from the voltmeter to termi- nal B7 and the negative ( −) lead to terminal B16.
(c) Push in the washer switch. Check that the voltage
changes, as shown in the table.
If operation is not as specified, replace the switch.
5. INSPECT REAR WIPER RELAY CONTINUITY
(a) Check that there is no continuity between terminals 1 and
3.
(b) Check that there is continuity between terminals 2 and 3.
If continuity is not as specified, replace the relay.
6. INSPECT REAR WIPER RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminal 1 and the negative ( −) lead to terminal 6.
(b) Connect the positive (+) lead from the voltmeter to termi- nal 2 and the negative ( −) lead to terminal 6, and check
that the meter needle indicates to O V.
(c) Connect the positive (+) lead from the voltmeter to termi-
nal 3 and the negative ( −) lead to terminal 6, and check
that the meter needle indicates to battery positive voltage.
If operation is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
BE−29
1996 LAND CRUISER (RM451U)
7. INSPECT REAR WIPER RELAY INTERMITTENT OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative ( −) lead to terminal 4.
(b) Connect the positive (+) lead from the voltmeter to termi- nal 3 and the negative ( −) lead to terminal 4.
(c) After disconnecting the positive (+) lead from terminal 2,
connect it to terminal 1, and then, check that the meter
needle rises from O V to battery positive voltage within 6
to 10 seconds.
If operation is not as specified, replace the relay.
8. Low Speed: INSPECT FRONT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 3 and
negative ( −) lead to terminal 1, and check that the motor oper-
ates at low speed.
If operation is not as specified, replace the motor.
9. High Speed:
INSPECT FRONT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and
the negative (− ) lead to terminal 1, and check that the motor op-
erates at high speed.
If operation is not as specified, replace the motor.
10. Stopping at Stop Position: INSPECT FRONT WIPER MOTOR OPERATION
(a) Operate the motor at low speed and stop the motor opera-
tion anywhere except at the stop position by disconnect-
ing positive (+) lead from terminal 3.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−30
−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
1996 LAND CRUISER (RM451U)
(b) Connect terminal 3 and 5.
(c) Connect the positive (+) lead from the battery to terminal
6 and the negative ( −) lead to terminal 1, and check that
the motor stops running at the stop position after the mo-
tor operates again.
If operation is not as specified, replace the motor.
11. Low Speed: INSPECT REAR WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 3 and
negative ( −) lead to terminal 2, and check that the motor oper-
ates at low speed.
If operation is not as specified, replace the motor.
12. Stopping at Stop Position: INSPECT REAR WIPER MOTOR OPERATION
(a) Operate the motor at low speed and stop the motor opera-
tion anywhere except at the stop position by disconnect-
ing positive (+) lead from terminal 3.
(b) Connect terminal 3 and 4.
(c) Connect the positive (+) lead from the battery to terminal 1 and the negative ( −) lead to terminal 2, and check that
the motor stops running at the stop position after the mo-
tor operates again.
If operation is not as specified, replace the motor.
13. INSPECT WASHER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and
the negative (− ) lead to terminal 1, and check that the motor op-
erates.
NOTICE:
These tests must be performed quickly (within 20 seconds)
to prevent the coil from burning out.
If operation is not as specified, replace the motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MB−01
−
BODY ELECTRICAL COMBINATION METER
BE−31
1169
Author: Date:
1996 LAND CRUISER (RM451U)
COMBINATION METER
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010