Drive TOYOTA LAND CRUISER 1996 J80 Workshop Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1996, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1996 J80Pages: 1399, PDF Size: 41.35 MB
Page 3 of 1399
Illustration:
what to do and where 21. CHECK
PISTON STROKE OF OVERDRIVE BRAKE
(a)
Task heading : what to do
SST 09350− 30020 (09350 −06120)
Set part No. Component part No.
Detailed text : how to do task
(b)
Piston stroke: 1.40 1.70 mm (0.0551 0.0669 in.)
Specification
Place SST and a dial indicator onto the overdrive brake pis-
ton as shown in the illustration.
Measure the stroke applying and releasing the compressed
air (392 785 kPa, 4 8 kgf/cm2 or 57
114 psi) as shown
in the illustration.
IN−2
−
INTRODUCTION HOW TO USE THIS MANUAL
2
Author: Date:
1996 LAND CRUISER (RM451U)
The procedures are presented in a step −by−step format:
The illustration shows what to do and where to do it.
The task heading tells what to do.
The detailed text tells how to perform the task and gives other information\
such as specifications
and warnings.
Example:
This format provides the experienced technician with a FAST TRACK to the information needed. The upper
case task heading can be read at a glance when necessary, and the text below it provides detailed informa-
tion. Important specifications and warnings always stand out in bold type.
6. REFERENCES
References have been kept to a minimum. However, when they are required you are given the page to refer
to.
7. SPECIFICATIONS
Specifications are presented in bold type throughout the text where needed. You never have to leave the
procedure to look up your specifications. They are also found in Service Specificatio\
ns section for quick ref-
erence.
8. CAUTIONS, NOTICES, HINTS:
CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other\
people.
NOTICES are also presented in bold type, and indicate the possibility of damage to the components
being repaired.
HINTS are separated from the text but do not appear in bold. They provide additional information to
help you perform the repair efficiently.
9. SI UNIT
The UNITS given in this manual are primarily expressed according to the SI UNIT (Intern\
ational System of
Unit), and alternately expressed in the metric system and in the English Syste\
m.
Example:
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 4 of 1399
Illustration:
what to do and where 21. CHECK
PISTON STROKE OF OVERDRIVE BRAKE
(a)
Task heading : what to do
SST 09350− 30020 (09350 −06120)
Set part No. Component part No.
Detailed text : how to do task
(b)
Piston stroke: 1.40 1.70 mm (0.0551 0.0669 in.)
Specification
Place SST and a dial indicator onto the overdrive brake pis-
ton as shown in the illustration.
Measure the stroke applying and releasing the compressed
air (392 785 kPa, 4 8 kgf/cm2 or 57
114 psi) as shown
in the illustration.
IN−2
−
INTRODUCTION HOW TO USE THIS MANUAL
2
Author: Date:
1996 LAND CRUISER (RM451U)
The procedures are presented in a step −by−step format:
The illustration shows what to do and where to do it.
The task heading tells what to do.
The detailed text tells how to perform the task and gives other information\
such as specifications
and warnings.
Example:
This format provides the experienced technician with a FAST TRACK to the information needed. The upper
case task heading can be read at a glance when necessary, and the text below it provides detailed informa-
tion. Important specifications and warnings always stand out in bold type.
6. REFERENCES
References have been kept to a minimum. However, when they are required you are given the page to refer
to.
7. SPECIFICATIONS
Specifications are presented in bold type throughout the text where needed. You never have to leave the
procedure to look up your specifications. They are also found in Service Specificatio\
ns section for quick ref-
erence.
8. CAUTIONS, NOTICES, HINTS:
CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other\
people.
NOTICES are also presented in bold type, and indicate the possibility of damage to the components
being repaired.
HINTS are separated from the text but do not appear in bold. They provide additional information to
help you perform the repair efficiently.
9. SI UNIT
The UNITS given in this manual are primarily expressed according to the SI UNIT (Intern\
ational System of
Unit), and alternately expressed in the metric system and in the English Syste\
m.
Example:
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 11 of 1399
IN0IO−01
BO4111
Negative Cable
−
INTRODUCTION FOR ALL OF VEHICLES
IN−9
9
Author: Date:
1996 LAND CRUISER (RM451U)
FOR ALL OF VEHICLES
PRECAUTION
1. FOR VEHICLES EQUIPPED WITH SRS AIRBAG AND
SEAT BELT PRETENSIONER
(a) The LAND CRUISER is equipped with an SRS (Supple-
mental Restraint System), such as the driver airbag and
front passenger airbag assembly.
Failure to carry out service operations in the correct se-
quence could cause the supplemental restraint system to
unexpectedly deploy during servicing, possibly leading to
a serious accident.
Further, if a mistake is made in servicing the supplemental
restraint system, it is possible the SRS may fail to operate
when required. Before servicing (including removal or
installation of parts, inspection or replacement), be sure
to read the following items carefully, then follow the cor-
rect procedure described in this manual.
(b) GENERAL NOTICE (1) Malfunction symptoms of the supplemental re-straint system are difficult to confirm, so the diag-
nostic trouble codes become the most important
source of information when troubleshooting. When
troubleshooting the supplemental restraint system,
always inspect the diagnostic trouble codes before
disconnecting the battery (See page DI−240).
(2) Work must be started after 90 seconds from the
time the ignition switch is turned to the ”LOCK” posi-
tion and the negative ( −) terminal cable is discon-
nected from the battery.
(The supplemental restraint system is equipped
with a back−up power source so that if work is
started within 90 seconds of disconnecting the neg-
ative (−) terminal cable from the battery, the SRS
may deploy.)
When the negative (−) terminal cable is discon-
nected from the battery, memory of the clock and
audio systems will be cancelled. So before starting
work, make a record of the contents memorized by
the each memory system. Then when work is fin-
ished, reset the clock and audio systems as before.
To avoid erasing the memory of each memory sys-
tem, never use a back− up power supply from anoth-
er battery.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 16 of 1399
V08127
IN−14
−
INTRODUCTION FOR ALL OF VEHICLES
14
Author: Date:
1996 LAND CRUISER (RM451U)
2. WHEN TOWING FULL −TIME 4WD VEHICLES
Use one of the methods shown below to tow the vehicle.
If the vehicle has trouble in the chassis and drive train, use method 1 \
(flat bed truck).
TransmissionTransfer(w/oASS)
~
Parking
ShiftLever
ShiftLever Center
Center
Towing Method Brake
Position PositionDifferential
Differential
Lock Switch
CDFlatSed Truck
~
IN0309
@WheelLiftType Truck with
Dollies FREE
Applied
lipIIRangeIIHIIPosition OFF(Normal)
~
Driving
ii-;~
@TowingwithRope
L~
ReleasedlINIIRangeIIN/IPosition
OFFt
IN0312
HINT:Donotuse anytowing methods otherthanthose shown above.
Forexample, thetowing method shownbelowisdangerous, sodo not use it.
NO
~
IN0313
During towing withthistowing method, thereisadanger of thedrivetrain
heating upand causing breakdown, orofthe front wheels flyingoffthe
dolly.
\127
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 17 of 1399
−
INTRODUCTION FOR ALL OF VEHICLES
IN−15
15
Author: Date:
1996 LAND CRUISER (RM451U)
3. FOR VEHICLES EQUIPPED WITH A CATALYTIC CONVERTER
CAUTION:
If large amount of unburned gasoline flows into the converter, it may overheat and create a fire haz-
ard. To prevent this, observe the following precautions and explain them to yo\
ur customer.
(a) Use only unleaded gasoline.
(b) Avoid prolonged idling.
Avoid running the engine at idle speed for more than 20 minutes.
(c) Avoid spark jump test. (1) Perform spark jump test only when absolutely necessary. Perform this test as rapidly as possible.
(2) While testing, never race the engine.
(d) Avoid prolonged engine compression measurement. Engine compression tests must be done as rapidly as possible.
(e) Do not run engine when fuel tank is nearly empty. This may cause the engine to misfire and create an extra load on the con\
verter.
(f) Avoid coasting with ignition turned off.
(g) Do not dispose of used catalyst along with parts contaminated with gasol\
ine or oil.
4. IF VEHICLE IS EQUIPPED WITH MOBILE COMMUNICATION SYSTEM
For vehicles with mobile communication systems such as two− way radios and cellular telephones, observe
the following precautions. (1) Install the antenna as far as possible away from the ECU and sensors of the vehicle’\
s electronic
system.
(2) Install the antenna feeder at least 20 cm (7.87 in.) away from the ECU and se\
nsors of the ve- hicle’s electronic systems. For details about ECU and sensors locations, refer\
to the section on
the applicable component.
(3) Avoid winding the antenna feeder together with other wiring as much as possible, and also avoid
running the antenna feeder parallel with other wire harnesses.
(4) Check that the antenna and feeder are correctly adjusted.
(5) Do not install powerful mobile communications system.
5. FOR USING OBD II SCAN TOOL OR TOYOTA HAND −HELD TESTER
CAUTION:
Observe the following items for safety reasons:
Before using the OBD II scan tool or TOYOTA hand −held tester, the OBD II scan tool’s instruc-
tion book or TOYOTA hand −held tester’s operator manual should be read thoroughly.
Be sure to route all cables securely when driving with the OBD II scan too\
l or TOYOTA hand −
held tester connected to the vehicle. (i.e. Keep cables away from feet,\
pedals, steering wheel
and shift lever.)
Two persons are required when test driving with the OBD II scan tool or TOYOTA hand −held
tester, one person to drive the vehicle and the other person to operate the OBD\
II scan tool or
TOYOTA hand−held tester.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 21 of 1399
Important Points in the Customer Problem Analysis
What −−−−− Vehicle model, system name
When −−−−− Date, time, occurrence frequency
Where −−−−− Road conditions
Under what conditions? −−−−− Running conditions, driving conditions, weather conditions
How did it happen? −−−−− Problem symptoms
(Sample) Engine control system check sheet.
ENGINE CONTROL SYSTEM Check Sheet
Customer’s Name
Driver’s Name
Data Vehicle
Brought in
License No.
Model and Model
Year
Frame No.
Engine Model
Odometer Reading
km
miles
Problem Symptoms
Engine does
not Start
Difficult to
Start
Poor Idling
Poor
Drive ability
Engine Stall
Others
Engine does not crankNo initial combustionNo complete combustion
Engine cranks slowly
Other
Incorrect first idleIdling rpm is abnormalHigh ( rpm)Low ( rpm)
Rough idling
Other
HesitationBack fireMuffler explosion (after− fire)Surging
Knocking
Other
Soon after startingAfter accelerator pedal depressed
After accelerator pedal released
During A/C operation
Shifting from N to D
Other
Data Problem
ConstantSometimes ( times per day/month)
Inspector’s
Name
CUSTOMER PROBLEM ANALYSIS CHECK
−
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN−19
1996 LAND CRUISER (RM451U)
1. CUSTOMER PROBLEM ANALYSIS
In troubleshooting, the problem symptoms must be confirmed accurately an\
d all preconceptions must be
cleared away in order to give an accurate judgment. To ascertain just what the problem symptoms are, it is
extremely important to ask the customer about the problem and the conditions at t\
he time it occurred.
Important Point in the Problem Analysis:
The following 5 items are important points in the problem analysis. Past pr\
oblems which are thought to be
unrelated and the repair history, etc. may also help in some cases, so as much information as possible s\
hould
be gathered and its relationship with the problem symptoms should be corre\
ctly ascertained for reference
in troubleshooting. A customer problem analysis table is provided in Diagnostics section for each system
for your use.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 36 of 1399
IN−34
−
INTRODUCTION TERMS
34
Author: Date:
1996 LAND CRUISER (RM451U)
CW
Curb W
eight
DCDirect Current
DEFDefogger
DFLDeflector
DIFF.Differential
DIFF. LOCKDifferential Lock
D/INJDirect Injection
DLIDistributorless Ignition
DOHCDouble Over Head Cam
DPDash Pot
DSDead Soak
DSPDigital Signal Processor
EBDElectronic Brake Force Distribution
ECAMEngine Control And Measurement System
ECDElectronic Controlled Diesel
ECDYEddy Current Dynamometer
ECUElectronic Control Unit
EDElectro−Deposited Coating
EDICElectric Diesel Injection Control
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGR−VMExhaust Gas Recirculation −Vacuum Modulator
ELREmergency Locking Retractor
ENGEngine
ESAElectronic Spark Advance
ETCSElectronic Throttle Control System
EVPEvaporator
E−VRVElectric V acuum Regulating V alve
EXHExhaust
FEFuel Economy
FFFront−Engine Front− Wheel−Drive
F/GFuel Gage
FIPGFormed In Place Gasket
FLFusible Link
F/PFuel Pump
FPUFuel Pressure Up
FrFront
FRFront−Engine Rear− Wheel−Drive
F/WFlywheel
FW/DFlywheel Damper
FWDFront−Wheel−Drive
GASGasoline
GSAGear Shift Actuator
GNDGround
HACHigh Altitude Compensator
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 37 of 1399
−
INTRODUCTION TERMS
IN−35
35
Author: Date:
1996 LAND CRUISER (RM451U)
H/B
Hatchback
H−FUSEHigh Current Fuse
HIHigh
HIDHigh Intensity Discharge (Head Lamp)
HPUHydraulic Power Unit
HSGHousing
HTHard Top
HWSHeated Windshield System
IACIdle Air Control
ICIntegrated circuit
IDIIndirect Diesel Injection
IFSIndependent Front Suspension
IGIgnition
IIAIntegrated Ignition Assembly
INIntake (Manifold, V
alve)
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
J/BJunction Block
J/CJunction Connector
KDKick−Down
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft−Hand
LHDLeft−Hand Drive
L/H/WLength, Height, Width
LLCLong− Life Coolant
LNGLiquified Natural Gas
LOLow
LPGLiquified Petroleum Gas
LSDLimited Slip Dif ferential
LSP & PVLoad Sensing Proportioning And Bypass V alve
LSPVLoad Sensing Proportioning Valve
MAX.Maximum
M−FUSEMedium Current Fuse
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MPMultipurpose
MPXMultiplex Communication System
M/TManual Transmission (T ransaxle)
MTMount
MTGMounting
NNeutral
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 38 of 1399
IN−36
−
INTRODUCTION TERMS
36
Author: Date:
1996 LAND CRUISER (RM451U)
NA
Natural Aspiration
No.Number
O/DOverdrive
OEMOriginal Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead V
alve
OPTOption
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
PKBParking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take−Off
R & PRack And Pinion
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight−Hand
RHDRight−Hand Drive
RLYRelay
ROMRead Only Memory
RrRear
RRRear−Engine Rear −Wheel Drive
RRSRigid Rear Suspension
RWDRear− Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SMTSequential Manual T ransmission
SOCState Of Charge
SOHCSingle Overhead Camshaft
SPECSpecification
SPISingle Point Injection
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
STJCold−Start Fuel Injection
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TBIThrottle Body Electronic Fuel Injection
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 39 of 1399
−
INTRODUCTION TERMS
IN−37
37
Author: Date:
1996 LAND CRUISER (RM451U)
TC
Turbocharger
TCCSTOYOTA
Computer− Controlled System
TCVTiming Control V alve
TDCTop Dead Center
TEMP.Temperature
TEMSTOYOTA Electronic Modulated Suspension
TISTotal Information System For Vehicle Development
T/MTransmission
TMCTOYOTA Motor Corporation
TMMKTOYOTA Motor Manufacturing Kentucky, Inc.
TRACTraction Control System
TURBOTurbocharge
U/DUnderdrive
U/SUndersize
VCVVacuum Control V alve
VENTVentilator
VINVehicle Identification Number
VPSVariable Power Steering
VSCVehicle Skid Control
VSVVacuum Switching Valve
VTVVacuum Transmitting V alve
w/With
WGNWagon
W/HWire Harness
w/oWithout
1stFirst
2ndSecond
2WDTwo Wheel Drive Vehicle (4x2)
4WDFour Wheel Drive Vehicle (4x4)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010