Drive TOYOTA LAND CRUISER 1996 J80 User Guide

AC−2
−
AIR CONDITIONING AIR CONDITIONING SYSTEM
1329
Author: Date:
1996 LAND CRUISER (RM451U)
9. SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
The LAND CRUISER is equipped with an SRS (Spplemental
Restraint System)such as the driver airbag and passenger air
bag. Failure to carry out service operations in the correct se-
quence could cause the SRS to unexpectedly deployed during
servicing, possibly leading to a serious accident. Further, if a
mistake is made in servicing the SRS, it is possible the SRS may
fail to operate when required. Before servicing (including re-
moval or installation of parts, inspection or replacement), be
sure to read the following item carefully, then follow the correct
procedure described in the repair manual.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2QC−03
−
AIR CONDITIONING AIR CONDITIONING SYSTEM
AC−3
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem.The numbers i\
ndicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspect AreaSee page
No blower operation
4. HTR Fuse
5. Heater main relay
6. Blower motor
7. Blower resistor
8. Blower speed control switch
9. Wire harness−
AC−64
AC−52
AC−57
AC−69 −
No air temperature control
1. Engine coolant volume
2. A/C control assembly
3. Water valve−
AC−69
AC−49
No compressor operation
1. Refrigerant volume
2. A.C Fuse
3. Magnetic clutch
4. Compressor
5. Pressure switch
6. Heater main relay
7. Blower speed control switch
8. A/C switch
9. A/C amplifier
10.Thermistor
11. Wire harnessAC−5 −
AC−33
AC−33
AC−61
AC−64
AC−69
AC−69
AC−74
AC−60 −
Compressor operates intermitently
1. Refrigerant volume
2. Pressure switch
3. A/C amplifier
4. Thermistor
5. Wire harnessAC−5
AC−61
AC−74
AC−60 −
No cool air comes out
1. Refrigerant volume
2. Refrigerant pressure
3. Drive belt
4. Magnetic clutch
5. Compressor
6. Pressure switch
7. Thermistor
8. A/C switch
9. A/C amplifier
10.A/C control assembly
11. Wire harnessAC−5
AC−5
AC−15
AC−33
AC−33
AC−61
AC−60
AC−69
AC−74
AC−69 −
Cool air comes out only at high engine rpm
1. Refrigerant volume
2. Drive bel
3. Magnetic clutch
4. Compressor
5. Condenser
6. Receiver
7. Expansion valve
8. Evaporator
9. Thermistor
10.A/C amplifier
11. Wire harnessAC−5
AC−15
AC−33
AC−33
AC−42
AC−39
AC−47
AC−45
AC−60
AC−74 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC−4
−
AIR CONDITIONING AIR CONDITIONING SYSTEM
1996 LAND CRUISER (RM451U)
Insuf
ficient cooling
1. Refrigerant volume
2. Drive belt
3. Magnetic clutch
4. Compressor
5. Condenser
6. Receiver
7. Expansion valve
8. Evaporator
9. Refrigerant line
10.Pressure switch
11. A/C amplifier
12.A/C control assemblyAC−5
AC−15
AC−33
AC−33
AC−42
AC−39
AC−47
AC−45
AC−20
AC−61
AC−74
AC−69
No engine idle up when A/C switch ON
1. A/C amplifier
2. ECM
3. Wire harnessAC−74 −
−
No warm air comes out
1. Engine coolant volume
2. A/C control assembly
3. Water valve
4. Heater radiator−
AC−69
AC−49
AC−46
A/C indicator does not light up when mode lever at DEF. position
1. Defroster mode switch
2. A/C switch
3. Wire harnessAC−69
AC−69 −
Rear heater:
SymptomSuspect AreaSee page
No blower operation
1. RR HTR Fuse
2. Rear heater relay
3. Rear heater switch
4. Rear blower motor
5. Rear blower resistor−
AC−65
AC−77
AC−55
AC−58
No warm air come out1. Engine coolant volume
2. Rear heater radiator−
AC−46
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CH0086
CorrectWrong
AC2QG−01
N01881
DENSOBorroughs
−
AIR CONDITIONING DRIVE BELT
AC−15
1342
Author: Date:
1996 LAND CRUISER (RM451U)
DRIVE BELT
ON−VEHICLE INSPECTION
1. INSPECT DRIVE BELT’S INSTALLATION CONDITION
Check that drive belt fits properly in the ribbed groves.
2. INSPECT DRIVE BELT TENSION
Using a belt tension gauge, check the drive belt tension.
Belt tension gauge:
DENSO BTG −20 (95506−00020) or
Borroughs No. BT −33−73F
Drive belt tension:
New belt 100−150 lbf
Used belt 60−100 lbf
HINT:
”New belt” refers to a belt which has been used less than
5 minutes on a running engine.
”Used belt” refers to a belt which has been on a running
engine for 5 minutes or more.
After installing the drive belt, check that it fits properly in
the ribbed grooves.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2QH−01
N16451
AC−16
−
AIR CONDITIONING DRIVE BELT
1996 LAND CRUISER (RM451U)
REMOVAL
1. LOOSEN IDLE PULLEY LOCK NUT Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
2. REMOVE COMPRESSOR DRIVE BELT
Loosen the adjusting bolt and remove the drive belt.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2QI−01
−
AIR CONDITIONING DRIVE BELT
AC−17
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page AC−16 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2R6−01
Z17949
Pressure Plate Rotor
Shim
Startor
Snap Ring Compressor
13.2
(135, 9)
Z17948
Suction Hose
Discharge Hose
Drive Belt
Compressor Compressor Bracket
O−Ring O−Ring
37 (375, 27)
N·m (kgf·cm, ft·lbf) : Specified torque
 Non− reusable part
10 (100, 7)
25 (250, 18)
37 (375, 27)
10 (100, 7)
AC−34
−
AIR CONDITIONING COMPRESSOR AND MAGNETIC CLUTCH
1996 LAND CRUISER (RM451U)
COMPONENTS
N16453 N14067
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2R7−04
AC0943
SST
AC0944
SST
AC0945
SST
−
AIR CONDITIONING COMPRESSOR AND MAGNETIC CLUTCH
AC−35
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. RUN ENGINE AT IDLE SPEED WITH A/C SWITCH ON
FOR 10 MINUTES
2. STOP ENGINE
3. DISCONNECT NEGATIVE ( −) TERMINAL CABLE
FROM BATTERY
4. DISCHARGE REFRIGERANT FROM REFRIGERA TION
SYSTEM
5. DISCONNECT DISCHARGE AND SUCTION HOSES
Remove the 2 bolts and disconnect the both hoses.
NOTICE:
Cap the open fittings immediately to keep the moisture or
dirt out of the system.
6. REMOVE ENGINE UNDER COVER
7. REMOVE DRIVE BELT (See page AC−16)
8. REMOVE COMPRESSOR
(a) Disconnect the connector.
(b) Remove the 4 bolts and pull the compressor upward.
9. REMOVE COMPRESSOR (See page AC−35 )
10. REMOVE PRESSURE PLATE
(a) Using SST and a socket wrench, remove the shaft bolt. Torque: 13.2 N·m (135 kgf·cm, 9 ft·lbf)
SST 07112 −76060
(b) Install a SST on the pressure plate. SST 07112 −66040
(c) Using SST and a socket wrench, remove the pressure plate.
SST 07112 −76060
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2R8−01
N04963
AC−38
−
AIR CONDITIONING COMPRESSOR AND MAGNETIC CLUTCH
1996 LAND CRUISER (RM451U)
REASSEMBLY
1. INSTALL COMPRESSOR
(a) Install the compressor with the 4 bolts. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Connect the connector.
2. CONNECT DISCHARGE AND SUCTION HOSES Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
NOTICE:
Hoses should be connected immediately after the caps
have been removed.
HINT:
Lubricate 2 new O −rings with compressor oil and install the
hoses.
3. INSTALL AND INSPECT DRIVE BELT (See page AC−17 )
4. INSTALL ENGINE UNDER COVER
5. CONNECT NEGATIVE ( −) TERMINAL CABLE TO BAT-
TERY
6. EVACUATE AIR FROM REFRIGERATION SYSTEM
7. CHARGE SYSTEM WITH REFRIGERANT AND IN- SPECT FOR LEAKAGE OF REFRIGERANT
Specified amount:
850 ± 50 g (29.98 ± 1.76 oz.)
Using a gas leak detector, check for leakage of refrigerant.
If there is leakage, check the tightening torque at the joints.
8. INSPECT A/C OPERATION
Reassembly is in the reverse order of disassembly (See
page AC−35 ).
9. CHECK CLEARANCE OF MAGNETIC CLUTCH
(a) Set the dial indicator to the pressure plate of the magnetic
clutch.
(b) Connect the magnetic clutch lead wire to the positive (+) terminal of the battery.
(c) Check the clearance between the pressure plate and ro- tor when connecting the negative ( −) terminal to the bat-
tery.
Standard clearance:
0.5 ± 0.15 mm (0.020 ± 0.0059 in.)
If the clearance is not within the standard clearance, adjust the
clearance using shims to obtain the standard clearance. Shim Thickness:
0.1 mm (0.004 in.)
0.3 mm (0.012 in.)
0.5 mm (0.020 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2RG−01
AC−42
−
AIR CONDITIONING CONDENSER
1369
Author: Date:
1996 LAND CRUISER (RM451U)
CONDENSER
ON−VEHICLE INSPECTION
1. INSPECT CONDENSER FINS FOR BLOCKAGE OR DAMAGE
If the fins are clogged, wash them with water and dry with compressed ai\
r.
NOTICE:
Be careful not to damage the fins.
If the fins are bent, straighten them with a screwdriver or pliers.
2. INSPECT CONDENSER AND FITTINGS FOR LEAKAGE
Repair as necessary.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010