TOYOTA LAND CRUISER 1998 Factory Manual Online
Manufacturer: TOYOTA, Model Year: 1998, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1998Pages: 3115, PDF Size: 54.88 MB
Page 81 of 3115
AC1LJ-04
I06818
- AIR CONDITIONINGPOWER TRANSISTOR (for Rear Heater)
AC-83
2808 Author: Date:
2004 LAND CRUISER (RM1071U)
POWER TRANSISTOR (for Rear
Heater)
INSPECTION
1. REMOVE FRONT SEATS
2. REMOVE REAR CONSOLE BOX
3. REMOVE FRONT CONSOLE BOX COVER
4. REMOVE LOWER CENTER CLUSTER FINISH PANEL
5. REMOVE FRONT DOOR SCUFF PLATES
6. REMOVE COWL SIDE TRIMS
7. REMOVE REAR DOOR SCUFF PATES
8. REMOVE CENTER PILLAR GARNISHES
9. REMOVE POWER TRANSISTOR
(a) Slide the floor carpet backward.
(b) Disconnect the connector.
(c) Remove the 2 screws and power transistor.
10. INSPECT POWER TRANSISTOR
Check the power transistor in the same way as for ºPOWER
TRANSISTOR (For Rear Cooler)º on page AC-82.
11. INSTALL POWER TRANSISTOR
12. INSTALL CENTER PILLAR GARNISHES
13. INSTALL REAR DOOR SCUFF PATES
14. INSTALL COWL SIDE TRIMS
15. INSTALL FRONT DOOR SCUFF PLATES
16. INSTALL LOWER CENTER CLUSTER FINISH PANEL
17. INSTALL FRONT CONSOLE BOX COVER
18. INSTALL REAR CONSOLE BOX
19. INSTALL FRONT SEATS
Page 82 of 3115
AC1LI-04
I06760
I07763
21
4
I07764
3
4 AC-82
- AIR CONDITIONINGPOWER TRANSISTOR (for Rear Cooler)
2807 Author: Date:
2004 LAND CRUISER (RM1071U)
POWER TRANSISTOR (for Rear
Cooler)
INSPECTION
1. REMOVE REAR DOOR SCUFF PLATE RH
2. REMOVE REAR FLOOR MAT SUPPORT PLATE
3. REMOVE QUARTER TRIM PANEL RH
4. REMOVE POWER TRANSISTOR
(a) Disconnect the connector.
(b) Remove the 2 screws and the power transistor.
5. INSPECT POWER TRANSISTOR OPERATION
(a) Connect the positive (+) lead to terminal 1 through a
12 V - 3.4 W test bulb and negative (-) lead to
terminal 2.
(b) Check the test bulb comes on when another positive (+)
lead is connected to terminal 4 through a 12 V - 3.4 W test
bulb.
If operation is not as specified, replace the power transistor.
6. INSPECT POWER TRANSISTOR RESISTANCE
Measure resistance between terminals 3 and 4.
Standard resistance: 2.0 - 2.4 kW
If resistance is not as specified, replace the power transistor.
7. INSTALL POWER TRANSISTOR
(a) Install the power transistor with 2 screws.
(b) Connect the connector.
8. INSTALL QUARTER TRIM PANEL RH
9. INSTALL REAR FLOOR MAT SUPPORT PLATE
10. INSTALL REAR DOOR SCUFF PLATE RH
Page 83 of 3115
AC1LU-02
- AIR CONDITIONINGPRESSURE SWITCH
AC-93
2818 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse of removal (See page AC-92).
Page 84 of 3115
AC3OW-01
I25168
1
23
4
Z13470
Magnetic clutch control
Low Pressure Side
ON (Continuity)
196 kpa
(2.0 kgf/cm
2, 28 psi)
OFF (No Continuity)High Pressure Side
3,140 kpa
(32.0 kgf/cm2, 455 psi)
OFF (No Continuity)
- AIR CONDITIONINGPRESSURE SWITCH
AC-91
2816 Author: Date:
2004 LAND CRUISER (RM1071U)
PRESSURE SWITCH
ON-VEHICLE INSPECTION
1. SET VEHICLE IN THESE CONDITION
(a) Engine speed at 1,500 rpm
(b) Blower speed control switch at ºHIº position
(c) Temperature control dial at ºMAX. COOLº position
(d) Manifold gauge set setting
2. INSPECT PRESSURE SWITCH OPERATION
(a) Disconnect the connector.
(b) Inspect pressure switch continuity (Magnetic Clutch Con-
trol)
(1) Connect the positive (+) lead from the ohmmeter to
terminal 1 and the negative (-) lead to terminal 2.
(2) Check continuity between terminals when the re-
frigerant pressure is changed, as shown in the il-
lustration.
If continuity is not as specified, replace the pressure switch.
Page 85 of 3115
AC1JE-04
I25169
AC-92
- AIR CONDITIONINGPRESSURE SWITCH
2817 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, evacuate air from refrigeration system
and charge system with refrigerant and inspect for leakage of
refrigerant.
Specified amount: 1,050 ± 50 g (37.03 ± 1.76 oz.)
2. REMOVE RADIATOR GRILL
3. REMOVE PRESSURE SWITCH FROM LIQUID TUBE
Disconnect the connector and remove the pressure switch.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
HINT:
Lock the switch mount on the tube with an open-end
wrench, be careful not to deform the tube, and remove the
switch.
At the time of installation, lubricate a new O-ring with
compressor oil and install the switch.
Page 86 of 3115
I06720
AC1MC-04
I06715
2
21
I06716
1 3
4
5 8
6 7 9
I06717
1
3 4 5 8
6 7 92
AC-108
- AIR CONDITIONINGREAR A/C CONTROL ASSEMBLY
2833 Author: Date:
2004 LAND CRUISER (RM1071U)
REAR A/C CONTROL ASSEMBLY
INSPECTION
1. REMOVE REAR HEATER CONTROL ASSEMBLY
Using a screwdriver, release the 4 claws and pull out the rear
heater control assembly, then disconnect the connector.
2. INSPECT ILLUMINATION OPERATION
Connect battery positive (+) lead to terminal 2 and battery nega-
tive (-) lead to terminal 21 then check that the indicators come
on.
If operation is not as specified, replace the rear A/C control as-
sembly.
3. INSPECT INDICATOR OPERATION
(a) Connect battery positive (+) lead to terminal 1 and battery
negative (-) lead to all the other terminals, then check that
the indicator come on, as shown in the chart.
SwitchTester connection
Auto3
LO4
ME5
HI6
FACE7
Bi-Level8
FOOT9
If operation is not as specified, replace the rear A/C control as-
sembly.
(b) Connect the positive (+) lead from the battery to terminal
2, then check where the indicators dim.
If operation is not as specified, replace the rear A/C control as-
sembly.
Page 87 of 3115
I06718
16 17
18
19
20 2213
14
15
I06719
To ºWARMº
12
11
W
- AIR CONDITIONINGREAR A/C CONTROL ASSEMBLY
AC-109
2834 Author: Date:
2004 LAND CRUISER (RM1071U)
4. INSPECT SWITCH CONTINUITY
Check the continuity between terminals while switch is pressed,
as shown in the chart.
SwitchTester connectionSpecified condition
Auto13 - 22Continuity
OFF14 - 22Continuity
LO15 - 22Continuity
ME16 - 22Continuity
HI17 - 22Continuity
FACE18 - 22Continuity
Bi-Level19 - 22Continuity
FOOT20 - 22Continuity
If continuity is not as specified, replace the rear A/C control as-
sembly.
5. INSPECT VARIABLE RESISTOR OPERATION
(a) Measure resistance between terminal 10 and 12.
Standard resistance: 3.0 kW
(b) Gradually move the temperature control lever from
ºCOOLº side to ºWARMº side, then check that the resis-
tance between terminal 11 and 12 increase to 3.0 kW.
If operation is not as specified, replace the rear A/C control as-
sembly.
6. INSTALL HEATER CONTROL ASSEMBLY
Page 88 of 3115
AC1KB-05
I25893
Roof Side Inner Upper Garnish Roof Headlining Rear Trim
No.1 Cooler Air Duct
Quarter Trim Panel RH
Rear Floor Mat Support Plate O-Ring
Liquid Tube
Suction Tube Rear Door Scuff Plate
43 (430, 32)
10 (100, 7)
43 (430, 32)
N´m (kgf´cm, ft´lbf) : Specified torque
Non-reusable part
Rear Cooling Unit
43 (430, 32)
Adjusting
Anchor
43 (430, 32)
AC-30
- AIR CONDITIONINGREAR COOLING UNIT
2755 Author: Date:
2004 LAND CRUISER (RM1071U)
COMPONENTS
Page 89 of 3115
I07785
A/C AmplifierCooling Unit CaseBlower Motor
Blower Motor Case
Power Transistor O-RingEvaporator
5.4 (55, 48 in.´lbf)
Thermistor
Expansion Valve O-Ring
O-Ring
A/C Tube
14 (140, 10)
A/C Tube
Drain HoseCooling Unit Case x11
Cooling Unit Case
Grommet
N´m (kgf´cm, ft´lbf) : Specified torque
Non-reusable part
32 (330, 24)
x10 Wire Harness
x7
- AIR CONDITIONINGREAR COOLING UNIT
AC-31
2756 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 90 of 3115
AC1KD-05
I06876
I06760
I06701
I06758
I06877x10 AC-34
- AIR CONDITIONINGREAR COOLING UNIT
2759 Author: Date:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. REMOVE A/C AMPLIFIER
Remove the 2 screws and the A/C amplifier.
2. REMOVE POWER TRANSISTOR
(a) Disconnect the connector.
(b) Remove the 2 screws and the power transistor.
3. REMOVE BLOWER CASE
(a) Remove the wire harness.
(b) Remove the 11 screws, 3 holding springs and separate
the cooling unit cases.
(c) Disconnect the connector.
(d) Remove the blower case.
4. REMOVE BLOWER MOTOR
Remove the 3 screws and the blower motor.
5. REMOVE EVAPORATOR
(a) Disconnect the 2 connector clamps.
(b) Remove the 10 screws and the 2 holding springs, and
separate the cooling unit cases.