remote start TOYOTA MR2 SPYDER 2001 Accessories, Audio & Navigation (in English)

TOYOTARS3200 remote keyless Security systemPage 15
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to notPASSIVELYARM. To change the system’s operation for PASSIVE
ARMINGoperation, as well as adjust the ENTRYDELAYtime, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin: Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.

a. Using the remote control,
lock, thenunlock the
doors 3 times . b. Open
the driver’s door.
b. Lock thenunlock the
driver’s door inside lock
button 1 time.

a. Close , then Open the door:
2 times = P
ASSIVEARMINGOFF
3 times = P
ASSIVEARMINGON ,
0 Sec. E
NTRYDELAY
4 times = PASSIVEARMINGON ,
15 Sec. E
NTRYDELAY
5 times = PASSIVEARMINGON ,
30 Sec. E
NTRYDELAY
c. Lock, thenunlock the
driver’s door inside lock
button 3 times .

d.The system locks the door
in 2 seconds; if this does
not happen, start over.
c.The system locks the door
in 2 seconds; if this does
not happen, start over.
Programming is now
complete.
e. Unlock
the driver’s door
inside lock button.

PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION
The RS3200 is factory-set to unlock the driver’s door when the UNLOCK button is pressed on the remote
control, then unlock the remaining doors when the UNLOCK button is press\
ed again within 3 seconds. You
may change the programming so all doors will unlock at once when the UNL\
OCK button is pressed by fol-
lowing the steps below.
1. Before you begin: 2. Start the Programming Procedure.Open the driver’s door. (Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.
Page 16 TOYOTARS3200 REMOTE KEYLESS Security system
a. Insert the key into, and remove it
from the ignition
switch 2 times.
e. Insert the key into
the ignition and leave it in.c. Insert the key into, and remove it
from the ignition
switch 1 time.
g. Turn the key from LOCK to ON 4
times (ending at
LOCK.) h. Remove the key
from the ignition
switch.
b. Close, then openthe driver’s door
2 times.
f. Close the driver’s door.d. Close, then openthe driver’s door
2 times.
i. The tail and marker lights flash 4 times, the buzzer chirps 4 times, and the doors lock and
unlock 4 times.

PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION (continued)
3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
TOYOTARS3200 remote keyless Security systemPage 17

a. Press and
release both
LOCK and
UNLOCK buttons
at the same time.
b. Press and release the
UNLOCK button
once for all doors
unlock.
or Press and release the
LOCK button
once for driver’s
door unlock.

e. Open the driver’s
door;
programming is
now complete.i.The tail and marker lights flash 1time, the
buzzer chirps 1 time, and the doors lock and
unlock 1time.

PROGRAMMING
IGNITION-CONTROLLED AUTOMATIC DOOR LOCK/UNLOCK
The RS3200 is factory-set to automatically lock your vehicle’s doors \
when you turn the ignition key
to “ON” or “START”, and unlock the doors when you turn the k\
ey back to “ACC” or “LOCK”. To
change the programming of this feature, follow the procedure shown below\
.
1. Before you begin:Open the driver’s door.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
Note: If the system does not activate the lights and buzzer, start over.\
3. Select the Operating Mode and Complete the Programming Procedure.
Page 18 TOYOTARS3200 REMOTE KEYLESS Security system

a. Insert the key into the
ignition switch and turn it
from LOCK to ON 5 times
(ending at ON). c.
The STATUSMONITOR’SLED
(or the engine immobilizer
system’s LED) turns on
for 30 seconds.
b. Turn the ignition
key backto lock.

a. Close the door =
IG. Controlled Door Locks ON
Close , then open and close
the door again= IG. Controlled
Door Locks OFF c.
The tail and marker lights
flash once and the buzzer
chirps once when the system is
set for IG door lock control ON ,
twice for IG door lock control
OFF . If this does not happen,
start over. Programming is now
complete.
b.
The tail and marker lights
flash once, and the buzzer
chirps once.