remote start TOYOTA MR2 SPYDER 2001 Accessories, Audio & Navigation (in English)

INTRODUCTION
Congratulations on your choice of the RS3200 remote keyless security sys\
tem to protect your
vehicle! To get the most from the system, we strongly recommend that you\
read this Owner’s
Guide completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enablin\
g you to A
RMand
D
ISARMat the same time you remotely lock and unlock the doors. The system prov\
ides comprehen-
sive security protection through point-of-entry monitoring, glass breaka\
ge detection and ignition
switch monitoring. While A
RMED, the system will be TRIGGEREDand sound an ALARMwhen a door,
trunk or hatch is forcibly unlocked or opened*, or when a window is tapp\
ed on or broken. During
the A
LARM, the vehicle’s horn sounds and the headlights, tail lights and front marker lights flash.
Also, the ve hicle’sstarter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUSMONITOR for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operatin\
g status) and the G
LASS
BREAKAGESENSOR’Smicrophone. In vehicles with an engine immobilizer, there is already a L\
ED
installed in the vehicle, so the RS3200 utilizes the engine immobilizer \
system LED and a micro-
phone mounted in a separate location. If your vehicle falls into this ca\
tegory, remember to look at
that LED when the information refers to the S
TATUSMONITOR. If you do not know where the LED is
located, refer to your vehicle’s owner’s guide for specific inform\
ation.
About the ignition-controlled automatic door locking/unlocking function.\
The RS3200 is programmed to automatically lock your vehicle’s doors w\
hen you turn the key in
the ignition switch to the “ON” or “START” position, and unl\
ock them when you turn the key back
to the “ACC” or “LOCK” position. You may disable this featur\
e by reprogramming the system; refer
to page 18 for programming information.
* When the system is P
ASSIVELY(AUTOMATICALLY) ARMED, there is an ENTRYDELAYthat will
elapse when a door is opened before an A
LARMis TRIGGERED.

YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE ILLUSTRATED HERE
LIGHTS FOR30SECONDS(PRE-ARMING)THEN STARTSFLASHING
(SYSTEM ISARMED)
Page 2 TOYOTARS3200 REMOTE KEYLESS Security system

 


Page 4 TOYOTARS3200 REMOTE KEYLESS Security system
FEATURESFUNCTIONS
The RS3200 will A
RM30 seconds after the LOCK button on the
remote control is pressed, and D
ISARMwhen the UNLOCK button is
pressed. When the LOCK button is pressed, all the vehicle’s doors
lock. When the UNLOCK button is pressed, the driver’s door
unlocks,* but if the UNLOCK button is pressed again within 3
seconds, the remaining doors unlock.
The RS3200 will automatically R
ELOCKthe vehicle’s doors if no door
is opened within 60 seconds after R
EMOTEDISARMING, the system will
R
EARM60 seconds later.
The RS3200 will A
RM30 seconds after you close the trunk (if open)
and lock the vehicle’s doors with the key, and will D
ISARMwhen you
unlock a door with the key.
While A
RMED, the trunk may be opened with the key (or the AUX
button on your remote control, if so equipped) without T
RIGGERINGan
A
LARM. Once the open trunk is closed, the system ARMSagain.
(See page 9 for more information.)
The RS3200 may be programmed to automatically A
RM30 seconds
after the ignition key is removed, the vehicle exited and the last door
and the trunk closed, without the necessity of locking the doors.
The RS3200 may be D
ISARMEDwith the vehicle’s ignition key after it
was P
ASSIVELYARMED.
When the RS3200 has been P
ASSIVELYARMED, an ENTRYDELAY(user-
selectable at 0, 15, or 30 seconds) will start when a door is opened
before an A
LARMis TRIGGERED.
When you lock the vehicle with a central lock switch (while a
door is open), the RS3200 will A
RM30 seconds after you close all
the doors and the trunk (if open).
The RS3200 may be D
ISARMEDby inserting the key into the ignition
switch and turning it to “ON.”
Forcibly unlocking or opening a door, hatch or trunk while the
RS3200 is A
RMEDwill TRIGGERan ALARMimmediately. (If the system
was P
ASSIVELYARMED, the ENTRYDELAYmust pass before the ALARMis
T
RIGGERED.)
The RS3200 utilizes a microphone (usually mounted in the S
TATUS
MONITOR) to sense the noise from tapping on window glass, or
glass breaking, and T
RIGGERan ALARM. It is fine tuned to “listen” for
this type of noise, and ignore other sounds.
When the G
LASSBREAKAGESENSOR’Smicrophone picks up tapping or
breaking of window glass, it T
RIGGERSa WARNAWAYALARM; the
headlights and tail and marker lights flash, and the horn sounds for
20 seconds, but the starter is not disabled. If there is another
detection of glass tapping or breaking, or if a door is opened or
unlocked without a key, the regular A
LARMis TRIGGERED.
While A
RMED, the RS3200 monitors the ignition switch. If an attempt
is made to start the vehicle without a key, an A
LARMis triggered.
** Starting from 2002 M.Y., Arming Suspension Mode by using the key to u\
nlock the trunk is not applicable to Camry, Solara, and Corolla.
* You may program the system to unlock all the doors with one press on t\
he UNLOCK button. See page 16 for programming instructions.
REMOTE
ARMING/DISARMING &
LOCKING/UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING/DISARMING
ARMED MODE
SUSPENSION **
PASSIVE (AUTOMATIC)
ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
GLASS BREAKAGE
SENSOR
WARN AWAY ALARM
IGNITION SWITCH
MONITORING
BRIEF DESCRIPTION–R
S3200 FEATURES

TOYOTARS3200 remote keyless Security system Page 5
FEATURESFUNCTIONS
When an A
LARMis TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (D
ISARMED).
During an A
LARM, the system will lock the doors if one is unlocked,
and will continue to do so for the duration of the A
LARM.
The user is notified that an A
LARM occurred. Upon DISARMING the
system after an A
LARMwas TRIGGERED, the vehicle’s tail and marker
lights will be turned on, and the B
UZZERsounds, for 2 seconds.
You may T
RIGGERaPANIC ALARM, by pressing the PANICbutton on the
back of the remote control, to draw attention to your vehicle. During
the P
ANIC ALARM, the head, tail and marker lights flash, and the horn
sounds, but the starter is not disabled.
The RS3200 flashes the vehicle’s tail and marker lights during
R
EMOTE ARMING and REMOTEDISARMING, as well as during an ALARM.
Also, the headlights flash during an A
LARM.
When the system is R
EMOTEDISARMED, it turns on the interior lights in
the vehicle for 30 seconds, or until the key is inserted into the
ignition switch. It also turns them on during an A
LARM.
During an A
LARM, the RS3200 activates the vehicle’s horn.
If power to the RS3200 is disrupted while it is A
RMED, an ALARM
is T
RIGGEREDonce power is restored.
This panel houses the G
LASS BREAKAGESENSORmicrophone and the
flashing LED that indicates the operating status of the security system.\
(In
vehicles with an engine immobilizer system, that system’s LED and a
separate microphone are used instead.)
The RS3200 utilizes a P
IEZO BUZZER, usually mounted in the engine
compartment, to sound confirmation “chirps” and tones for function\

confirmation and programming step confirmation.
The RS3200 automatically locks your vehicle’s doors when you turn
the ignition key to “ON” or “START”, and unlocks the doors when you
turn the key back to “ACC” or “LOCK”.*
The Buzzer sounds for 5 seconds when you attempt to R
EMOTE ARM
the system while a door is open. You can stop the warning by closing the
door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with
the RS3200 is approximately 50 feet. Please refer to page 10 for a
description of factors that may affect the performance (operating
range) of the remote controls.
* You may disable this feature. Please refer to page 18 for programming inf\
ormation. STARTER DISABLE
FORCED LOCK
DURING ALARM
TRIGGER MEMORY
PANIC MODE
OPERATION
EXTERIOR LIGHT
ACTIVATION
INTERIOR LIGHT
ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-
CONTROLLED
AUTOMATIC DOOR
LOCK/UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
BRIEF DESCRIPTION–RS3200 FEATURES

Page 6 TOYOTARS3200 REMOTE KEYLESS Security system
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMEDin several ways. Do oneof the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the trunk or hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of \
the vehicle: The S
TATUSMONITOR’SLED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the trunk or hatch, if necessary.* Then: The S
TATUSMONITOR’SLED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the trunk or hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously: The doors lock.

The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The STATUSMONITOR’SLED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
* The system will not A
RMwhile any of the doors, trunk or hatch is open. However, when you press
the LOCK button when the trunk is open, the doors will lock; the system \
will arm 30 seconds
after the trunk is closed.

TURN TOWARD THE FRONT
OF THE VEHICLE

PRESS AND RELEASETHE LOCK BUTTON

PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN
LIGHTS FOR30SECONDS(PRE-ARMING)THEN
FLASHES
(SYSTEM IS ARMED)

THE TAIL AND MARKER LIGHTS FLASH ONCE WHEN THE SYSTEM IS REMOTE ARMED
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS REMOTE ARMED

Page 8
TOYOTA
RS3200 REMOTE KEYLESS Security system

OPERATION

PASSIVE (AUTOMATIC) ARMING & DISARMING

When the RS3200 is programmed to PASSIVELYARM, the system will ARMafter the ignition key is
removed and all doors and the trunk or hatch are closed; you do not need\
to lock the doors. When
you come back to your vehicle and open a door, you must insert the key i\
nto the ignition switch
and turn it to “ON” during the E
NTRYDELAY(0, 15 or 30 seconds), or an ALARMwill be TRIGGERED. If
you lock the doors, regular A
RMINGwill override PASSIVEARMING; there will be no ENTRYDELAY. See
the PROGRAMMING section on page 15 to activate the P
ASSIVEARMINGmode, as well as select the
E
NTRYDELAYtime.

To PASSIVELYARMthe system:

Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (

The system will not ARM
while any of the doors are open.)

Close the trunk or hatch, if necessary. (
The system will not ARMwhile
the trunk or hatch is open.)

After the last door, trunk or hatch is closed: The S
TATUSMONITOR’SLED turns on for 30 seconds, then
starts flashing.

The system is now ARMED.

To DISARMthe PASSIVELYARMEDsystem:

Enter the vehicle through a front door.
The E
NTRYDELAYbegins:
The S
TATUSMONITOR’SLED turns on (no flashing.)


Insert the key into the ignition switch and turn it to “ON”before the
E
NTRYDELAYends.*
The LED turns off. The system is now D
ISARMED.

You may also DISARMthe system following any of the methods
described on page 7.

NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sound\
s for 2 seconds when the system is D
ISARMED, the TRIGGERMEMORYwas activated; an ALARMwas
T
RIGGEREDwhile you were away from the vehicle.

* If the ENTRYDELAYtime elapses before the ignition switch is turned to “ON”, an ALARMwill be
T
RIGGERED. To DISARMthe system during an ALARM, insert the ignition key and turn it to “ON”, or
press and release the remote control’s UNLOCK button.

THE SYSTEM ARMS30SECONDS
AFTER THE LAST ENTRY POINT
(DOOR,TRUNK OR HATCH)IS CLOSED

THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN IT TO
“ON”

LIGHTS FOR30SECONDS(PRE-ARMING)THEN STARTSFLASHING
(SYSTEM ISARMED)



TURNS ON(NO
FLASHING)DURING THE
ENTRY DELAY



TOYOTARS3200 remote keyless Security systemPage 9
OPERATION
AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 is DISARMEDat the same time.
However, if you do not open a door or the trunk or hatch within 30 secon\
ds, the system will relock
the doors and the RS3200 will R
EARM30 seconds later
How the RS3200 automatically R
EARMS:
ARMING SUSPENSION **
The ARMEDstate of the RS3200 can be suspended temporarily by using the key to unl\
ock and
open the trunk. When the A
RMINGis suspended, the STATUSMONITOR’SLED will turn offuntil the
trunk is closed again.
** Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to
Camry, Solara, and Corolla.

0
15
30
45
THE DOORS ARE UNLOCKED
BY PRESSING THE UNLOCK BUTTON ON THE REMOTE CONTROL
...
WHEN NO DOOR,TRUNK
OR HATCH IS OPENED...FOR MORE THAN30SECONDS...THE RS3200AUTOMATICALLY RELOCKS THE DOORS,THEN
AUTOMATICALLY REARMS.
THE LED LIGHTS UP FOR30SECONDS(PRE-ARM),THEN
FLASHES WHEN THE SYSTEM IS ARMED

TURNS OFFWHEN THE
ARMED STATE
IS SUSPENDED

Page 10 TOYOTARS3200 REMOTE KEYLESS Security system
MISCELLANEOUS
DOOR AJAR WARNING
The RS3200 will sound a five second DOORAJARWARNINGwhen you attempt to REMOTEARMthe
system while a door is open. To stop the warning tone, either close the \
open door, or press and
release the UNLOCK button on the remote control. To A
RMthe system, press the LOCK button
again.
Note: The D
OORAJARWARNINGwill not sound when the trunk is open; the doors will lock, but the
system will not A
RMuntil the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING
The RS3200 is programmed to automatically lock your vehicle’s doors w\
hen you turn the ignition
key to “ON” or “START”, and unlock the doors when you turn t\
he key back to “ACC” or “LOCK”. If
you start the vehicle while a door is open, the system will not lock the\
doors; you must lock them
manually.
How the RS3200 automatically locks and unlocks the doors :
This feature may be defeated by changing the system’s programming. Re\
fer to page 18 for
programming instructions.
REMOTE CONTROL RANGE
The maximum range for the RS3200’s remote controls is 50 feet. Howeve\
r, several factors that
may affect your remote control’s actual performance, include, but are\
not limited to:
➯The remote control’s battery strength* (weak battery = decreased per\
formance).
➯Your position relative to the vehicle (dependent on the system’s ant\
enna wire location).
➯Objects in the path between you and your vehicle.
➯Your surroundings (in a parking structure, out in the open, etc.).
➯Outside electrical interference caused by high tension power lines, etc.\
* As the REMOTE CONTROL’s battery becomes weaker, the LED indicator bec\
omes dimmer. When you notice the LED becoming dimmer, you should replace the battery.\

WITH ALL THE DOORS
CLOSED,TURN THE KEY TO
THE“ON”OR“LOCK”POSITION...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY.WHEN THE KEY IS TURNED BACK TO THE“ACC”OR“LOCK”POSITION...
ALL THE DOORS ARE UNLOCKED.

Page 12 TOYOTARS3200 REMOTE KEYLESS Security system
ALARM INFORMATION
ALARM TRIGGERS
While the system is ARMED, an ALARMwill be TRIGGEREDwhen any of the following occurs:
Forcibly opening a door, or the trunk or hatch without a key
Pulling the trunk or hatch release lever inside the vehicle will also
T
RIGGERan ALARM.
Manually unlocking a door
Manually operating an inside lock button will T
RIGGERan ALARM.
Note: Because this action will T
RIGGERan ALARM, it is important
that you do not A
RMthe system while someone is in the
vehicle.
“Hot wiring” the vehicle
The RS3200 can detect the absence of the ignition key if the ignition
circuit is shorted in attempt to start the vehicle.
Tapping on or breaking the glass
The noise from tapping on, or breaking of glass T
RIGGERSa WARN
AWAYALARMfirst, then a regular ALARM. See the description of how
the G
LASSBREAKAGESENSORTRIGGERSALARMSon page 14.
Power restoration
If power to the system is interrupted while it is A
RMED, an ALARMwill
be T
RIGGEREDimmediately when power is restored.

TOYOTARS3200 remote keyless Security systemPage 13
ALARM INFORMATION
ALARM DESCRIPTIONS
RegularALARM
When an ALARMis triggered in any way other than initial detection by the GLASSBREAKAGESENSOR,
the following occur: The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
The starter is disabled (no engine start) until the system is D
ISARMED.
The door lock will be relocked if someone reaches in and unlocks the ins\
ide lock button.
After 60 seconds of A
LARM, the system will REARMand continue to protect the vehicle.
W
ARN-AWAY ALARM
Upon initial detection of noise from tapping on, or breaking glass, the \
GLASSBREAKAGESENSOR
TRIGGERSa WARNAWAYALARM:
The horn sounds repeatedly for 20 seconds.
The headlights flash repeatedly for 20 seconds.
The tail and marker lights flash repeatedly for 20 seconds.
The interior lights turn on for 20 seconds.
If the G
LASSBREAKAGESENSORdetects noise again, or if a door or trunk or hatch is opened while the
system is still A
RMED, the regular ALARM(described above) is activated.
STOPPING AN ALARM
Simply DISARMthe system using the remote control or key as described on page 7.

THE HORN SOUNDS
FOR20SECONDS

HEADLIGHTS FLASHFOR20SECONDS
MARKER LIGHTS FLASH
FOR
20SECONDS
TAIL LIGHTS FLASH FOR20SECONDS

THE HORN SOUNDS FOR60SECONDS
HEADLIGHTS FLASHFOR60SECONDS
THE STARTER IS DISABLED UNTIL THE SYSTEM IS DISARMED
MARKER LIGHTS FLASH
FOR
60SECONDS TAIL LIGHTS FLASH
FOR
60SECONDS
INTERIOR LIGHTS TURN ON FOR60SECONDS
INTERIOR LIGHTS TURN ON FOR20SECONDS


Page 14 TOYOTARS3200 REMOTE KEYLESS Security system
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry p\
oint monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. \
Using a microphone designed
specifically for this task, the G
LASSBREAKAGESENSORis capable of ignoring other noises, which
helps to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust \
the sensitivity level of the
G
LASSBREAKAGESENSOR. You may observe how it works following the procedure listed below.
1. A
RMthe system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not A
RMif any door, the trunk or hatch is
open.)
2. Wait until the S
TATUSMONITOR’SLED starts flashing.
The LED will flash 30 seconds after the last door, the trunk or hatch
is closed.
3. With the tip of a key, tap the center of the driver’s door window. Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.
A W
ARNAWAYALARMshould be TRIGGERED. If the ALARMis not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Toyota dealer for more information.
4. D
ISARMthe system to stop the WARNAWAYALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARMthe system.