ECO mode TOYOTA MR2 SPYDER 2001 Accessories, Audio & Navigation (in English)

Page 4 TOYOTARS3200 REMOTE KEYLESS Security system
FEATURESFUNCTIONS
The RS3200 will A
RM30 seconds after the LOCK button on the
remote control is pressed, and D
ISARMwhen the UNLOCK button is
pressed. When the LOCK button is pressed, all the vehicle’s doors
lock. When the UNLOCK button is pressed, the driver’s door
unlocks,* but if the UNLOCK button is pressed again within 3
seconds, the remaining doors unlock.
The RS3200 will automatically R
ELOCKthe vehicle’s doors if no door
is opened within 60 seconds after R
EMOTEDISARMING, the system will
R
EARM60 seconds later.
The RS3200 will A
RM30 seconds after you close the trunk (if open)
and lock the vehicle’s doors with the key, and will D
ISARMwhen you
unlock a door with the key.
While A
RMED, the trunk may be opened with the key (or the AUX
button on your remote control, if so equipped) without T
RIGGERINGan
A
LARM. Once the open trunk is closed, the system ARMSagain.
(See page 9 for more information.)
The RS3200 may be programmed to automatically A
RM30 seconds
after the ignition key is removed, the vehicle exited and the last door
and the trunk closed, without the necessity of locking the doors.
The RS3200 may be D
ISARMEDwith the vehicle’s ignition key after it
was P
ASSIVELYARMED.
When the RS3200 has been P
ASSIVELYARMED, an ENTRYDELAY(user-
selectable at 0, 15, or 30 seconds) will start when a door is opened
before an A
LARMis TRIGGERED.
When you lock the vehicle with a central lock switch (while a
door is open), the RS3200 will A
RM30 seconds after you close all
the doors and the trunk (if open).
The RS3200 may be D
ISARMEDby inserting the key into the ignition
switch and turning it to “ON.”
Forcibly unlocking or opening a door, hatch or trunk while the
RS3200 is A
RMEDwill TRIGGERan ALARMimmediately. (If the system
was P
ASSIVELYARMED, the ENTRYDELAYmust pass before the ALARMis
T
RIGGERED.)
The RS3200 utilizes a microphone (usually mounted in the S
TATUS
MONITOR) to sense the noise from tapping on window glass, or
glass breaking, and T
RIGGERan ALARM. It is fine tuned to “listen” for
this type of noise, and ignore other sounds.
When the G
LASSBREAKAGESENSOR’Smicrophone picks up tapping or
breaking of window glass, it T
RIGGERSa WARNAWAYALARM; the
headlights and tail and marker lights flash, and the horn sounds for
20 seconds, but the starter is not disabled. If there is another
detection of glass tapping or breaking, or if a door is opened or
unlocked without a key, the regular A
LARMis TRIGGERED.
While A
RMED, the RS3200 monitors the ignition switch. If an attempt
is made to start the vehicle without a key, an A
LARMis triggered.
** Starting from 2002 M.Y., Arming Suspension Mode by using the key to u\
nlock the trunk is not applicable to Camry, Solara, and Corolla.
* You may program the system to unlock all the doors with one press on t\
he UNLOCK button. See page 16 for programming instructions.
REMOTE
ARMING/DISARMING &
LOCKING/UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING/DISARMING
ARMED MODE
SUSPENSION **
PASSIVE (AUTOMATIC)
ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
GLASS BREAKAGE
SENSOR
WARN AWAY ALARM
IGNITION SWITCH
MONITORING
BRIEF DESCRIPTION–R
S3200 FEATURES

TOYOTARS3200 remote keyless Security system Page 5
FEATURESFUNCTIONS
When an A
LARMis TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (D
ISARMED).
During an A
LARM, the system will lock the doors if one is unlocked,
and will continue to do so for the duration of the A
LARM.
The user is notified that an A
LARM occurred. Upon DISARMING the
system after an A
LARMwas TRIGGERED, the vehicle’s tail and marker
lights will be turned on, and the B
UZZERsounds, for 2 seconds.
You may T
RIGGERaPANIC ALARM, by pressing the PANICbutton on the
back of the remote control, to draw attention to your vehicle. During
the P
ANIC ALARM, the head, tail and marker lights flash, and the horn
sounds, but the starter is not disabled.
The RS3200 flashes the vehicle’s tail and marker lights during
R
EMOTE ARMING and REMOTEDISARMING, as well as during an ALARM.
Also, the headlights flash during an A
LARM.
When the system is R
EMOTEDISARMED, it turns on the interior lights in
the vehicle for 30 seconds, or until the key is inserted into the
ignition switch. It also turns them on during an A
LARM.
During an A
LARM, the RS3200 activates the vehicle’s horn.
If power to the RS3200 is disrupted while it is A
RMED, an ALARM
is T
RIGGEREDonce power is restored.
This panel houses the G
LASS BREAKAGESENSORmicrophone and the
flashing LED that indicates the operating status of the security system.\
(In
vehicles with an engine immobilizer system, that system’s LED and a
separate microphone are used instead.)
The RS3200 utilizes a P
IEZO BUZZER, usually mounted in the engine
compartment, to sound confirmation “chirps” and tones for function\

confirmation and programming step confirmation.
The RS3200 automatically locks your vehicle’s doors when you turn
the ignition key to “ON” or “START”, and unlocks the doors when you
turn the key back to “ACC” or “LOCK”.*
The Buzzer sounds for 5 seconds when you attempt to R
EMOTE ARM
the system while a door is open. You can stop the warning by closing the
door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with
the RS3200 is approximately 50 feet. Please refer to page 10 for a
description of factors that may affect the performance (operating
range) of the remote controls.
* You may disable this feature. Please refer to page 18 for programming inf\
ormation. STARTER DISABLE
FORCED LOCK
DURING ALARM
TRIGGER MEMORY
PANIC MODE
OPERATION
EXTERIOR LIGHT
ACTIVATION
INTERIOR LIGHT
ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-
CONTROLLED
AUTOMATIC DOOR
LOCK/UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
BRIEF DESCRIPTION–RS3200 FEATURES

Page 8
TOYOTA
RS3200 REMOTE KEYLESS Security system

OPERATION

PASSIVE (AUTOMATIC) ARMING & DISARMING

When the RS3200 is programmed to PASSIVELYARM, the system will ARMafter the ignition key is
removed and all doors and the trunk or hatch are closed; you do not need\
to lock the doors. When
you come back to your vehicle and open a door, you must insert the key i\
nto the ignition switch
and turn it to “ON” during the E
NTRYDELAY(0, 15 or 30 seconds), or an ALARMwill be TRIGGERED. If
you lock the doors, regular A
RMINGwill override PASSIVEARMING; there will be no ENTRYDELAY. See
the PROGRAMMING section on page 15 to activate the P
ASSIVEARMINGmode, as well as select the
E
NTRYDELAYtime.

To PASSIVELYARMthe system:

Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (

The system will not ARM
while any of the doors are open.)

Close the trunk or hatch, if necessary. (
The system will not ARMwhile
the trunk or hatch is open.)

After the last door, trunk or hatch is closed: The S
TATUSMONITOR’SLED turns on for 30 seconds, then
starts flashing.

The system is now ARMED.

To DISARMthe PASSIVELYARMEDsystem:

Enter the vehicle through a front door.
The E
NTRYDELAYbegins:
The S
TATUSMONITOR’SLED turns on (no flashing.)


Insert the key into the ignition switch and turn it to “ON”before the
E
NTRYDELAYends.*
The LED turns off. The system is now D
ISARMED.

You may also DISARMthe system following any of the methods
described on page 7.

NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sound\
s for 2 seconds when the system is D
ISARMED, the TRIGGERMEMORYwas activated; an ALARMwas
T
RIGGEREDwhile you were away from the vehicle.

* If the ENTRYDELAYtime elapses before the ignition switch is turned to “ON”, an ALARMwill be
T
RIGGERED. To DISARMthe system during an ALARM, insert the ignition key and turn it to “ON”, or
press and release the remote control’s UNLOCK button.

THE SYSTEM ARMS30SECONDS
AFTER THE LAST ENTRY POINT
(DOOR,TRUNK OR HATCH)IS CLOSED

THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN IT TO
“ON”

LIGHTS FOR30SECONDS(PRE-ARMING)THEN STARTSFLASHING
(SYSTEM ISARMED)



TURNS ON(NO
FLASHING)DURING THE
ENTRY DELAY



TOYOTARS3200 remote keyless Security systemPage 9
OPERATION
AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 is DISARMEDat the same time.
However, if you do not open a door or the trunk or hatch within 30 secon\
ds, the system will relock
the doors and the RS3200 will R
EARM30 seconds later
How the RS3200 automatically R
EARMS:
ARMING SUSPENSION **
The ARMEDstate of the RS3200 can be suspended temporarily by using the key to unl\
ock and
open the trunk. When the A
RMINGis suspended, the STATUSMONITOR’SLED will turn offuntil the
trunk is closed again.
** Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to
Camry, Solara, and Corolla.

0
15
30
45
THE DOORS ARE UNLOCKED
BY PRESSING THE UNLOCK BUTTON ON THE REMOTE CONTROL
...
WHEN NO DOOR,TRUNK
OR HATCH IS OPENED...FOR MORE THAN30SECONDS...THE RS3200AUTOMATICALLY RELOCKS THE DOORS,THEN
AUTOMATICALLY REARMS.
THE LED LIGHTS UP FOR30SECONDS(PRE-ARM),THEN
FLASHES WHEN THE SYSTEM IS ARMED

TURNS OFFWHEN THE
ARMED STATE
IS SUSPENDED

ALARM INFORMATION
PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attenti\
on to your vehicle by
pressing the PANIC button on the back of the remote control. Unless you \
D
ISARMthe PANICALARM
by one of the described methods, it will continue for 60 seconds, then s\
top.To activate the P
ANICALARM:
Press the PANIC button on the back of the remote control. Simultaneously\
: The horn sounds repeatedly for 60 seconds.

The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANICALARMat any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARMTRIGGERduring the PANICALARM, the
regular A
LARMtakes over. See ALARM INFORMATION on pages 12 and 13 for additional
information.

TOYOTARS3200 remote keyless Security system Page 11
PRESS THE
LOCK BUTTON ON THE
REMOTE
CONTROL
,OR...
PRESS THE
PANIC BUTTON AGAIN
,OR...
PRESS THE UNLOCK
BUTTON ON
THE REMOTE CONTROL
,OR...
LOCK THE DOORS
WITH THE KEY,OR...UNLOCK A DOOR OR THE TRUNK WITH THE KEY

THE HORN SOUNDSFOR60SECONDS

HEADLIGHTS FLASHFOR60SECONDS
MARKER LIGHTS FLASH
FOR
60SECONDS
TAIL LIGHTS FLASH FOR60SECONDS
INTERIOR LIGHTS TURN ON FOR60SECONDS

Page 14 TOYOTARS3200 REMOTE KEYLESS Security system
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry p\
oint monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. \
Using a microphone designed
specifically for this task, the G
LASSBREAKAGESENSORis capable of ignoring other noises, which
helps to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust \
the sensitivity level of the
G
LASSBREAKAGESENSOR. You may observe how it works following the procedure listed below.
1. A
RMthe system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not A
RMif any door, the trunk or hatch is
open.)
2. Wait until the S
TATUSMONITOR’SLED starts flashing.
The LED will flash 30 seconds after the last door, the trunk or hatch
is closed.
3. With the tip of a key, tap the center of the driver’s door window. Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.
A W
ARNAWAYALARMshould be TRIGGERED. If the ALARMis not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Toyota dealer for more information.
4. D
ISARMthe system to stop the WARNAWAYALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARMthe system.

TOYOTARS3200 remote keyless Security systemPage 15
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to notPASSIVELYARM. To change the system’s operation for PASSIVE
ARMINGoperation, as well as adjust the ENTRYDELAYtime, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin: Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.

a. Using the remote control,
lock, thenunlock the
doors 3 times . b. Open
the driver’s door.
b. Lock thenunlock the
driver’s door inside lock
button 1 time.

a. Close , then Open the door:
2 times = P
ASSIVEARMINGOFF
3 times = P
ASSIVEARMINGON ,
0 Sec. E
NTRYDELAY
4 times = PASSIVEARMINGON ,
15 Sec. E
NTRYDELAY
5 times = PASSIVEARMINGON ,
30 Sec. E
NTRYDELAY
c. Lock, thenunlock the
driver’s door inside lock
button 3 times .

d.The system locks the door
in 2 seconds; if this does
not happen, start over.
c.The system locks the door
in 2 seconds; if this does
not happen, start over.
Programming is now
complete.
e. Unlock
the driver’s door
inside lock button.

PROGRAMMING
IGNITION-CONTROLLED AUTOMATIC DOOR LOCK/UNLOCK
The RS3200 is factory-set to automatically lock your vehicle’s doors \
when you turn the ignition key
to “ON” or “START”, and unlock the doors when you turn the k\
ey back to “ACC” or “LOCK”. To
change the programming of this feature, follow the procedure shown below\
.
1. Before you begin:Open the driver’s door.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
Note: If the system does not activate the lights and buzzer, start over.\
3. Select the Operating Mode and Complete the Programming Procedure.
Page 18 TOYOTARS3200 REMOTE KEYLESS Security system

a. Insert the key into the
ignition switch and turn it
from LOCK to ON 5 times
(ending at ON). c.
The STATUSMONITOR’SLED
(or the engine immobilizer
system’s LED) turns on
for 30 seconds.
b. Turn the ignition
key backto lock.

a. Close the door =
IG. Controlled Door Locks ON
Close , then open and close
the door again= IG. Controlled
Door Locks OFF c.
The tail and marker lights
flash once and the buzzer
chirps once when the system is
set for IG door lock control ON ,
twice for IG door lock control
OFF . If this does not happen,
start over. Programming is now
complete.
b.
The tail and marker lights
flash once, and the buzzer
chirps once.