remote control TOYOTA RAV4 1996 Service Repair Manual

bezel. Remove interior window control switch by prying up on front of plastic switch retaining plate. See
Fig. 24
and Fig. 25 . Remove armrest. Remove side door panel courtesy light and wiring harness
connector. Remove upper armrest base panel. Remove 3 screws. Pry door trim away from door.
2. Remove 2 screws, linkage rod and inside door handle assembly. Remove service hole cover. Disconnect
harness connector from power mirror, if equipped. Remove 3 bolts and remove outside rear view mirror
assembly. Remove 3 screws and remove speaker. Remove 2 bolts and remove window glass. Remove
door molding at top of door, where window slides. See Fig. 27
.
3. Remove window track. Remove electrical connector from window regulator (if equipped) and remove
window regulator through service hole. Remove door lock actuator linkage, 3 screws and remove door
lock actuator through service hole. To install reverse removal procedure. See TORQUE
SPECIFICATIONS .
Removal & Installation (Tacoma)
1. Remove window crank handle on non-power window equipped vehicles. Remove screw and slide interior
door handle forward and remove handle from control link. Remove door lock bezel. Remove clip from
armrest panel and disconnect electrical connectors. Remove 2 screws. Pry interior door panel loose from
door. Lift upward and remove door panel.
2. Remove 5 screws and remove speaker. Remove service hole cover. With power remote mirrors, remove
electrical connectors and 3 bolts. Remove weather stripping and glass channel. Remove front lower glass
frame. Open door glass until nut appears in service hole. Remove 2 bolts and remove door glass by lifting
upward. Remove rear lower glass frame.
3. Disconnect harness connector and remove 6 bolts and remove window regulator. Disconnect 3 screws
and linkage from door lock assembly. Remove door lock assembly. To install, reverse removal procedure.
See TORQUE SPECIFICATIONS
.
Removal & Installation (Tundra)
1. Remove window crank handle on non-power window equipped vehicles. Remove inside door handle
bezel. See Fig. 26
. Remove interior window control switch by prying up on front of plastic switch
retaining plate. See Fig. 24
and Fig. 25 . Remove side door panel courtesy light and wiring harness
connector. Remove tweeter speaker. Remove 2 screws and pry door trim away from door.
2. Remove inner and lower weather strip from door. Remove screw and slide inside door handle backward
and remove it. Disconnect 2 cables from inside door handle. Remove service hole cover. Remove 3
speaker screws and remove speaker. Disconnect remote mirror wiring harness. Remove 3 screws from
mirror and remove mirror assembly. Remove glass track and remove door molding at top of door, where
window slides. See Fig. 28
. Remove door glass channel. Remove front and lower frames. Open door
glass until bolts appear in service hole. Remove 2 bolts and remove door glass.
3. Remove harness connector, nut and bolts for window regulator and remove regulator through service
hole. Disconnect linkage from door lock actuator, remove bolt and remove 3 Torx (T-30) screws and
remove door lock actuator. To install, reverse removal procedure. See TORQUE SPECIFICATIONS
.

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Door Locks - Trucks
Microsoft
Sunday, November 22, 2009 10:53:11 AMPage 28 © 2005 Mitchell Repair Information Company, LLC.

Fig. 28: Identifying Door Molding Attachment Points (Tundra)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Removal & Installation (4Runner)
1. Remove window crank handle on non-power window equipped vehicles. Remove interior door handle
screw and slide door handle forward. Disconnect door handle from link and remove door handle. Remove
door arm rest. Remove interior window control switch by prying up on front of plastic switch retaining
plate. See Fig. 24
and Fig. 25 . Remove 2 clips and 2 screws and pry door trim away from door.
2. Remove inner rear view mirror cover. Disconnect remote mirror wiring harness. Remove 3 screws from
mirror and remove mirror assembly. Remove service hole cover. Remove inner and outer weather strip
from door. Remove front and lower frames. Open door glass until bolts appear in service hole. Remove
door glass channel. Remove 2 bolts and remove door glass.
3. Remove harness connector, nut and bolts for window regulator and remove regulator through service
hole. Disconnect linkage from door lock actuator, remove bolt and remove 6 mounting screws. Remove
door lock actuator. To install, reverse removal procedure. See TORQUE SPECIFICATIONS
.
POWER DOOR LOCK ACTUATORS (REAR DOORS)
Removal & Installation (Land Cruiser)
1. Remove inside door handle bezel screw plug, screw and bezel. Remove interior window control switch

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Door Locks - Trucks
Microsoft
Sunday, November 22, 2009 10:53:11 AMPage 29 © 2005 Mitchell Repair Information Company, LLC.