lubric TOYOTA RAV4 2006 Service Owner's Manual

PP–26PREPARATION – 2AZ-FE LUBRICATION
PP
SSM
Toyota Genuine Adhesive 1344, Three Bond 1344B or Equivalent -

PREPARATION – 2GR-FE LUBRICATIONPP–25
PP
EQUIPMENT
Container -
Deep socket wrench (24 mm) -
Hose Oil filter
Oil pressure gauge -
Socket wrench (27 mm) -
Straightedge -
Torque wrench -
Wooden block -

PP–26PREPARATION – 2GR-FE LUBRICATION
PP
LUBRICANT
Item Capacity Classification
Oil grade - ILSAC multigrade engine oil is
recommended. SAE 5W-30 is the
best choice for good fuel
economy and good starting in
cold weather.
Drain and refill With oil filter change 6.1 liters ( 6.4 US qts, 5.4 Imp.
qts)-
Without oil filter change 5.7 liters ( 6.0 US qts, 5.0 Imp.
qts)-
Dry fill 6.5 liters ( 6.9 US qts, 5.7 Imp.
qts)-

PREPARATION – 2GR-FE LUBRICATIONPP–27
PP
SSM
Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent -
Toyota Genuine Seal Packing Block, Three Bond 1207B or Equivalent -
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or
Equivalent-

PREPARATION – U151E AUTOMATIC TRANSMISSIONPP–41
PP
LUBRICANT
Automatic transaxle fluid
Dry fill
Drain and refill8.1 liter (8.6 US qts, 7.1 Imp.qts)
3.6 liter (3.8 US qts, 3.2 Imp.qts)Toyota Genuine ATF WS

PREPARATION – U151F AUTOMATIC TRANSMISSIONPP–47
PP
LUBRICANT
Automatic transaxle fluid
Dry fill
Drain and refill8.1 liter (8.6 US qts, 7.1 Imp.qts)
3.6 liter (3.8 US qts, 3.2 Imp.qts)Toyota Genuine ATF WS

PP–54PREPARATION – U140F AUTOMATIC TRANSAXLE
PP
LUBRICANT
Automatic transaxle fluid
Dry fill (w/ Warmer)8.1 liters (8.6 US qts, 7.2 Imp. qts) Toyota Genuine ATF WS
Automatic transaxle fluid
Drain and refill (w/ Warmer)3.5 liters (3.7 US qts, 3.1 Imp. qts)

PREPARATION – U241E AUTOMATIC TRANSAXLEPP–61
PP
LUBRICANT
Automatic transaxle fluid
Dry fill8.1 liters (8.6 US qts, 7.2 Imp. qts) Toyota Genuine ATF WS
Automatic transaxle fluid
Drain and refill3.5 liters (3.7 US qts, 3.1 Imp. qts)

PREPARATION – AIR CONDITIONINGPP–83
PP
LUBRICANT
Item Capacity Classification
Compressor oil - ND-OIL 8 or equivalent

2AZ-FE LUBRICATION – OIL PUMPLU–15
LU
REASSEMBLY
1. INSTALL OIL PUMP ROTOR
(a) Coat the drive rotor and driven rotor with engine oil.
(b) Place the drive and driven rotors into the oil pump
with the marks facing the pump cover side.
2. INSTALL OIL PUMP COVER
(a) Install the oil pump cover with the 5 bolts.
Torque: 8.8 N*m (90 kgf*cm, 78 in.*lbf)
3. INSTALL OIL PUMP RELIEF VALVE
(a) Coat the relief valve with engine oil.
(b) Insert the relief valve and spring into the pump body
hole.
(c) Using a 27 mm socket wrench, install the plug.
Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf)
4. INSTALL OIL PUMP STRAINER
(a) Install a new gasket and the oil strainer with the 2
nuts.
Torque: 8.8 N*m (90 kgf*cm, 78 in.*lbf)
B011423E02
B011431E01
A052074E02
B011430E01