TOYOTA SEQUOIA 2001 Service Repair Manual

H23862
Lance
Retainer Holder
Retainer
1
2
H23916
AA
Lever
RS±10
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
3293 Author: Date:
2005 SEQUOIA (RM1146U)
(5) Connector lock mechanism (2):
Both the primary lock with holder lances and the
secondary lock with retainer prevent the connectors
from becoming disconnected.
(6) Improper connection prevention lock mechanism:
When connecting the holder, the lever is pushed
into the end by rotating around the A axis to lock the
holder securely.

H23907
(a)(b) Lock Button
(Yellow Part)Lock Button
(Yellow Part)
H23908
Lock Button
(Yellow Part)
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
RS±11
3294 Author: Date:
2005 SEQUOIA (RM1146U)
16. DISCONNECTION OF CONNECTORS FOR STEERING WHEEL PAD AND CURTAIN SHIELD AIR-
BAG ASSEMBLY
(a) Release the lock button (yellow part) of the connector using a screwdriver.
(b) Insert the screwdriver tip between the connector and the base, and then raise the connector.
17. CONNECTION OF CONNECTORS FOR STEERING WHEEL PAD AND CURTAIN SHIELD AIRBAG
ASSEMBLY
(a) Connect the connector.
(b) Push down securely on the lock button (yellow part) of the connector. (When locking, a click sound can
be heard.)

H01586
SliderSlider
Disconnection is completed
H01587
Slider
Connection is completed
Slider RS±12
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
3295 Author: Date:
2005 SEQUOIA (RM1146U)
18. DISCONNECTION OF FRONT PASSENGNR AIRBAG ASSEMBLY
(a) Place a finger on the slider, slide the slider to release the lock, and then disconnect the connector.
19. CONNECTION OF FRONT PASSENGNR AIRBAG ASSEMBLY
(a) Connect the connector as shown in the illustration. (When locking, make sure that the slider returns
to its original position and a click sound can be heard.)
HINT:
When connecting, the slider will slide. Be sure not to touch the slider while connecting, as it may result in
an insecure fit.

H23909
A
Disconnection is completed Holder (with connectors)
H23910
Retainer
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
RS±13
3296 Author: Date:
2005 SEQUOIA (RM1146U)
20. DISCONNECTION OF CONNECTOR FOR AIRBAG SENSOR ASSY CENTER
(a) Pull the lever by pushing part A as shown in the illustration and disconnect the holder (with connectors).
HINT:
Perform the following procedures when replacing the holder.
(b) Remove the holder.
(1) Using a screwdriver, unlock the retainer.

H23911
Lances
H23912
RS±14
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
3297 Author: Date:
2005 SEQUOIA (RM1146U)
(2) Release the fitting lances and remove the holder.
(c) Install the holder.
(1) Install the connectors to the holder. (When locking,
a click sound can be heard.)
HINT:
The retainer is locked when the holder is connected.

H23913
Connection is completed Lever
Holder (with connectors)
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
RS±15
3298 Author: Date:
2005 SEQUOIA (RM1146U)
21. CONNECTION OF CONNECTOR FOR AIRBAG SENSOR ASSY CENTER
(a) Firmly insert the holder (with connectors) until it can not be pushed any further.
(b) Push the lever to connect the holder (with connectors). (When locking, a click sound can be heard.)
HINT:
The holder slides when connecting. Be sure not to hold the holder while connecting, as it may result in an
insecure fit.

H24685
Housing Lock (White Part) A
CPA (Yellow Part)
Connector
lock is
released
H24686
RS±16
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
3299 Author: Date:
2005 SEQUOIA (RM1146U)
22. DISCONNECTION OF CONNECTOR FOR FRONT AIRBAG SENSOR
(a) Push down the housing lock (white part) and slide the CPA (yellow part). (At this time, the connector
cannot be disconnected yet).
(b) Push down the housing lock (white part) again and disconnect the connector.
HINT:
Do not push down the A part shown in the illustration when disconnecting.
(c) After disconnecting the connector, check that the position of the housing lock (the white part) is as
shown in the illustration.

H24687
H24688
Housing Lock
(White Part) A
CPA (Yellow Part)
Connection is
completed
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
RS±17
3300 Author: Date:
2005 SEQUOIA (RM1146U)
23. CONNECTION OF CONNECTOR FOR FRONT AIRBAG SENSOR
(a) Before connecting the connectors, check that the position of the housing lock (the white part) is as
shown in the illustration.
(b) Be sure to engage the connectors until they are locked. (When locking, make sure that a click sound
can be heard.)
HINT:
When connecting them, the housing lock (white part) slides. Be sure not to hold the housing lock (white part)
and A part, as it may result in an insecure fit.

H01584
Slider
Disconnection is completed Slider
H01585
SliderSlider
RS±18
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
3301 Author: Date:
2005 SEQUOIA (RM1146U)
24. DISCONNECTION OF CONNECTOR FOR SIDE AIRBAG ASSEMBLY
(a) Place a finger on the slider, slide the slider to release the lock, and then disconnect the connector.
25. CONNECTION OF CONNECTOR FOR SIDE AIRBAG ASSEMBLY
(a) Connect the connector as shown in the illustration. (When locking, make sure that the slider returns
to its original position and a click sound can be heard.)
HINT:
When connecting, the slider will slide. Be sure not to touch the slider while connecting, as it may result in
an insecure fit.

H02763
Outer
H02764
Lock of connector is released
Disconnection is completed
H02768
Outer
Outer
Connection is completed
± SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
RS±19
3302 Author: Date:
2005 SEQUOIA (RM1146U)
26. DISCONNECTION OF CONNECTORS FOR SIDE AIR-
BAG SENSOR AND CURTAIN SHIELD AIRBAG SEN-
SOR
(a) While holding both outer flank sides, slide the outer in the
direction shown by the arrow.
(b) When the connector lock is released, the connectors are
disconnected.
HINT:
Be sure to hold both outer flank sides. Holding the top and bot-
tom sides will make disconnection difficult.
27. CONNECTION OF CONNECTORS FOR SIDE AIRBAG SENSOR AND CURTAIN SHIELD AIRBAG
SENSOR
(a) Connect the connector as shown in the illustration. (When locking, make sure that the outer returns
to its original position and a click sound can be heard.)
HINT:
When connecting, the outer will slide. Be sure not to hold the outer while connecting, as it may result in an
insecure fit.