TOYOTA TERCEL 1996 Service Repair Manual

BR0786
BR0RC-06
BR5045
BR-8
- BRAKEPARKING BRAKE LEVER
882 Author
: Date
:
1996 TERCEL (RM440U)
PARKING BRAKE LEVER
ON-VEHICLE INSPECTION
1. CHECK PARKING BRAKE LEVER TRAVEL
Pull the parking brake lever all the way up, and count the num-
ber of clicks.
Parking brake lever travel at 196 N (20 kgf, 44.1 lbf):
5 - 8 clicks
2. IF NECESSARY, ADJUST PARKING BRAKE
HINT:
Before adjusting the parking brake, make sure that the rear
brake shoe clearance has been adjusted.
For shoe clearance adjustment, see step 2 on page BR-33.
(a) Remove the console box.
(b) Loosen the lock nut and turn the adjusting nut until the le-
ver travel is correct.
(c) Tighten the lock nut.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(d) Install the console box.

BR0RD-06
F04745
Air Cleaner Assembly
2-wayBrake Booster
Master Cylinder Clamp

Gasket w/o ABS:
w/o ABS:
w/ ABS:
Cap
Stariner
Reservoir
Set ScrewNo.1 Piston and Spring
GrommetSnap Ring
Master Cylinder Body
Piston Stopper Bolt Reservoir

GasketNo.2 Piston and SpringCap
Stariner
Reservoir
Grommet
Reservoir Set Screw
No.1 Piston and Spring
Snap Ring
No.2 Piston and Spring
Master Cylinder Body

Gasket

Non-reusable partw/ ABS:
Lithium soap base glycol grease
- BRAKEBRAKE MASTER CYLINDER
BR-9
883 Author
: Date
:
1996 TERCEL (RM440U)
BRAKE MASTER CYLINDER
COMPONENTS

BR0RE-01
BR5042
SST
BR5041
BR-10
- BRAKEBRAKE MASTER CYLINDER
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE AIR CLEANER ASSEMBLY
2. DISCONNECT LEVEL WARNING SWITCH CONNEC-
TOR
3. DRAW OUT FLUID WITH SYRINGE
NOTICE:
Do not let brake fluid remain on a painted surface. Wash it
off immediately.
4. DISCONNECT BRAKE LINES
Using SST, disconnect the brake lines from the master cylinder.
SST 09751-3601 1
Torque: 15 N´m (155 kgf´cm, 11 ft´lbf)
5. REMOVE MASTER CYLINDER
(a) w/o ABS:
Remove the 2 mounting nuts, clamp and pull out the mas-
ter cylinder and gasket.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)
(b) w/ ABS:
Remove the 2 mounting nuts, 2-way and pull out the
master cylinder and gasket.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)

BR0RF-06
BR5036
Soft Jaws
BR5037
Soft Jaws
R12236
A
- BRAKEBRAKE MASTER CYLINDER
BR-1 1
1996 TERCEL (RM440U)
DISASSEMBLY
1. REMOVE RESERVOIR
(a) Remove the set screw and pull out the reservoir.
Torque: 1.7 N´m (17.5 kgf´cm, 15.2 in.´lbf)
(b) Remove the cap and strainer from the reservoir.
2. REMOVE 2 GROMMETS
3. PLACE CYLINDER IN VISE
4. REMOVE PISTON STOPPER BOLT
Using a screwdriver, push the pistons in all the way and remove
the piston stopper bolt and gasket.
HINT:
Tape the screwdriver tip before use.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
5. REMOVE PISTONS
(a) Push in the piston with a screwdriver and remove the
snap ring with snap ring pliers.
(b) Remove the No.1 piston and spring by hand, pulling
straight out, not at an angle.
NOTICE:

If pulled out and installed at an angle, there is a possi-
bility that the cylinder bore could be damaged.

Be careful not to damage the rubber lips on the pis-
tons.
(c) Place a rag and 2 wooden blocks on the work table and
lightly tap the cylinder flange against the block edges until
the No.2 piston drops out of the cylinder.
HINT:
Make sure the distance (A) from the rag to the top of the blocks
is at least 100 mm (3.94 in.).

BR0RG-01
BR-12
- BRAKEBRAKE MASTER CYLINDER
1996 TERCEL (RM440U)
INSPECTION
HINT:
Clean the disassembled parts with compressed air.
1. INSPECT CYLINDER BORE FOR RUST OR SCORING
2. INSPECT CYLINDER FOR WEAR OR DAMAGE
If necessary, clean or replace the cylinder.

BR0RH-02
- BRAKEBRAKE MASTER CYLINDER
BR-13
1996 TERCEL (RM440U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page BR-1 1).
NOTICE:
Apply lithium soap base glycol grease to the rubber parts indicated by arrows (See page BR-9).

BR0RI-05
BR-14
- BRAKEBRAKE MASTER CYLINDER
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-10).
1. BEFORE INSTALLATION, ADJUST LENGTH OF BRAKE BOOSTER PUSH ROD (See page
BR-18)
2. AFTER INSTALLATION, FILL BRAKE RESERVOIR WITH BRAKE FLUID AND BLEED BRAKE
SYSTEM (See page BR-4)
3. CHECK FOR LEAKS, CHECK AND ADJUST BRAKE PEDAL (See page BR-6)

BR2237
BR0RJ-01
BR2238
GOOD NO GOOD
1st2nd3rd
- BRAKEBRAKE BOOSTER ASSEMBLY
BR-15
889 Author
: Date
:
1996 TERCEL (RM440U)
BRAKE BOOSTER ASSEMBLY
ON-VEHICLE INSPECTION
1. OPERATING CHECK
(a) Depress the brake pedal several times with the engine off
and check that there is no change in the pedal reserve
distance.
(b) Depress the brake pedal and start the engine. If the pedal
goes down slightly, operation is normal.
2. AIR TIGHTNESS CHECK
(a) Start the engine and stop it after 1 or 2 minutes. Depress
the brake pedal several times slowly.
If the pedal goes down farthest the 1st time, but gradually rises
after the 2nd or 3rd time, the booster is air tight.
(b) Depress the brake pedal while the engine is running, and
stop the engine with the pedal depressed. If there is no
change in the pedal reserve travel after holding the pedal
for 30 seconds, the booster is air tight.

BR0RK-06
R12151
Air Cleaner Assembly
Brake Booster Master Cylinder

Non-reusable part2-way Clamp
Gasket
Gasket
Clip
Pin
Clevis w/o ABS:
w/ ABS:Clip Vacuum Hose
BR-16
- BRAKEBRAKE BOOSTER ASSEMBLY
1996 TERCEL (RM440U)
COMPONENTS

BR0RL-01
F05027
BR5055
R04651
- BRAKEBRAKE BOOSTER ASSEMBLY
BR-17
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE MASTER CYLINDER (See page BR-10)
2. DISCONNECT VACUUM HOSE FROM BRAKE
BOOSTER
3. REMOVE PEDAL RETURN SPRING
4. REMOVE CLIP AND CLEVIS PIN
5. REMOVE BRAKE BOOSTER
(a) Remove the No.1 brake line clamp.
(b) Remove the No.2 brake line clamp.
(c) Remove the 4 nuts and clevis.
(d) Pull out the brake booster and gasket.