engine VOLKSWAGEN CORRADO 1993 Manual PDF
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1993, Model line: CORRADO, Model: VOLKSWAGEN CORRADO 1993Pages: 920, PDF Size: 6.92 MB
Page 304 of 920

2.8L IN-LINE V6 (VR6)
Article Text (p. 13)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
2) Mark piston in relation to pin. Remove circlips from ends
of pin bore. Use Piston Pin Replacer/Installer (VW 222A) to remove and
install piston pin. If pin is too tight, heat piston to 140øF (60øC).
Ensure rod is properly positioned with piston.
Fitting Pistons
Measure clearances with cylinder block supported on work
bench. Check clearance of piston-to-cylinder bore. Piston diameter is
stamped on top of piston in millimeters.
PISTON-TO-CYLINDER BORE DIMENSIONS TABLE
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Piston Diameter Cylinder Bore
Size In. (mm) In. (mm)
Standard .......... 3.188 (80.98) ........ 3.189 (81.01)
1st Over .......... 3.208 (81.49) ........ 3.209 (81.51)
2nd Over .......... 3.228 (81.98) ........ 3.229 (82.01)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Piston Rings
1) Measure ring end gap. Measure ring side clearance with
piston. Replace if necessary. See PISTONS, PINS & RINGS SPECIFICATIONS
table under ENGINE SPECIFICATIONS at end of article.
2) Install rings on piston with OBEN or TOP mark facing
upward. Recessed edge on outside of center ring must face piston pin
(down). Position ring gaps on piston at 120 degree intervals.
Connecting Rod Bearings
Mark rod caps for reinstallation. Use Plastigage to measure
bearing clearances. Measure connecting rod side play. Replace or
machine as necessary. See CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS
table under ENGINE SPECIFICATIONS at end of article. Tighten evenly to
specification in several steps. See TORQUE SPECIFICATIONS table at end
of article.
Crankshaft & Main Bearings
Main bearing caps are marked with matching journal for
installation in original position. See Fig. 16. Measure crankshaft end
play. See THRUST BEARING.
Page 305 of 920

2.8L IN-LINE V6 (VR6)
Article Text (p. 14)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PMFig. 16: Exploded View Of Crankshaft Assembly
Courtesy of Volkswagen United States, Inc.
Thrust Bearing
Insert feeler gauge between No. 5 main bearing and crankshaft
thrust face to measure end play. See Fig. 16. Replace thrust bearing
as necessary. See CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS table
under ENGINE SPECIFICATIONS at end of article.
Cylinder Block
Check cylinder bore for wear, out-of-round and taper. Check
cylinder block for warpage. See CYLINDER BLOCK table under ENGINE
SPECIFICATIONS at end of article.
Page 306 of 920

2.8L IN-LINE V6 (VR6)
Article Text (p. 15)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
ENGINE OILING
ENGINE LUBRICATION SYSTEM
Crankcase Capacity
See CRANKCASE CAPACITY table.
CRANKCASE CAPACITY TABLEÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ With Filter Without Filter
Model Replacement Replacement
2.8L ............. 6.3 Qts. (6.0L) ..... 5.3 Qts. (5.0L)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Oil Pressure
Check oil pressure with engine at warm operating temperature.
Minimum oil pressure at 2000 RPM is 29 psi (2.0 kg/cm
ý). If oil
pressure is incorrect, check oil pump and oil pressure relief valve.
OIL PUMP
Removal & Installation
Remove oil pan. Remove oil pump attaching bolts and remove
oil pump assembly. To install, reverse removal procedure.
Inspection
Check oil pump housing, gears and pressure relief valve for
damage or excessive wear. See Fig. 17. Repair or replace as an
assembly.Fig. 17: Oil Pump Assembly
Courtesy of Volkswagen United States, Inc.
Page 307 of 920

2.8L IN-LINE V6 (VR6)
Article Text (p. 16)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLEÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄApplication Ft. Lbs. (N.m)
A/C Bracket-To-Engine Bolt ....................... 22 (30)
Axle Shaft-To-Transaxle Drive Flange Bolt ........ 33 (45)
Camshaft Bearing Cap Bolt ........................ 15 (20)
Camshaft Sprocket Bolt .......................... 74 (100)
Clutch Cover Bolt ................................ 15 (20)
Connecting Rod Bolt ................... 22 (30) + 1/4 Turn
Crankshaft Main Bearing Cap Bolt ...... 22 (30) + 1/2 Turn
Cylinder Head Bolt (1)
Step 1 ......................................... 30 (40)
Step 2 ......................................... 44 (60)
Step 3 ....................... Additional 1/4 (90
ø) Turn
Step 4 ....................... Additional 1/4 (90
ø) Turn
Engine Bracket (Front) ........................... 44 (60)
Engine Bracket (To Body) ......................... 33 (45)
Engine-To-Transaxle 10-mm Bolt ................... 44 (60)
Engine-To-Transaxle 12-mm Bolt ................... 55 (80)
Exhaust Manifold-To-Cylinder Head Bolt & Nut ..... 18 (25)
Exhaust Pipe-To-Catalytic Converter Bolt ......... 18 (25)
Exhaust Pipe-To-Manifold Nut ..................... 30 (40)
Flywheel-To-Crankshaft Bolt ........... 44 (60) + 1/4 Turn
Intake Manifold .................................. 18 (25)
Intermediate Shaft Sprocket Bolt ................ 74 (100)
Oil Pan Bolt ..................................... 15 (20)
Oil Pan Drain Plug ............................... 37 (50)
Oil Pressure Switch .............................. 18 (25)
Oil Pump Cover Long Bolt ............................. (2)
Oil Pump Cover Short Bolt ........................ 18 (25)
Power Steering Pump Bracket Bolt ................. 18 (25)
Pressure Plate Bolt .............................. 15 (20)
Starter Mount Bolt ............................... 18 (25)
Timing Belt Tensioner Nut ........................ 15 (20)
Torque Converter-To-Carrier Plate Bolt ........... 22 (30)
Vibration Damper Bolt .......................... 332 (450)
Water Pump Pulley Bolt ........................... 15 (20)
Water Pump Housing-To-Engine Bolt ................ 15 (20)
INCH Lbs. (N.m)
Fuel Rail Bolt (Lower) ............................ 89 (10)
Timing Belt Idler Bolt ........................... 89 (10)
Valve Cover Retaining Nut ........................ 89 (10)
Water Pump-To-Housing ........................... 115 (13)
(1) - Never reuse cylinder head bolt(s) when servicing.
(2) - Tighten bolt to 89 INCH lbs. (10 N.m).
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Page 308 of 920

2.8L IN-LINE V6 (VR6)
Article Text (p. 17)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
ENGINE SPECIFICATIONS
GENERAL ENGINE SPECIFICATIONS
GENERAL ENGINE SPECIFICATIONS TABLEÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄApplication Specification
Displacement ........................... 170 Cu. In. (2.8L)
Bore ...................................... 3.19" (81.0 mm)
Stroke .................................... 3.56" (90.3 mm)
Compression Ratio .................................. 10.5:1
Fuel System .................................. Motronic MFI
Horsepower @ RPM
Corrado SLC ................................... 178 @ 5800
Passat ........................................ 172 @ 5800
Torque Ft. Lbs @ RPM ........................... 177 @ 4200
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS SPECS
CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS SPECS TABLE
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄApplication In. (mm)
Crankshaft
End Play
Standard ........................... .003-.007 (.07-.17)
Service Limit ............................... .010 (.25)
Runout ...................................... .001 (.03)
Main Bearings
Journal Diameter .............. 2.361-2.363 (59.98-60.04)
Journal Out-Of-Round ......................... .001 (.03)
Journal Taper ................................ .001 (.03)
Oil Clearance
Standard ......................... .0008-.0020 (.02-.06)
Service Limit ............................... .007 (.17)
Connecting Rod Bearings
Journal Diameter .............. 1.881-1.883 (47.78-47.84)
Journal Out-Of-Round ......................... .001 (.03)
Journal Taper ................................ .001 (.03)
Oil Clearance ...................... .0004-.002 (.01-.06)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ PISTONS, PINS & RINGS SPECIFICATIONS
PISTONS, PINS & RINGS SPECIFICATIONS TABLE
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄApplication In. (mm)
Pistons
Page 312 of 920

A - ENGINE/VIN ID
Article Text
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
ARTICLE BEGINNING
1993 ENGINE PERFORMANCE
Volkswagen Introduction
All Models
MODEL COVERAGE
MODEL COVERAGE TABLEÚÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄ¿
³
³ Body ³ ³Engine³ ³ Ignition ³
³ Model
³ Code ³ Engine ³ ID ³ Fuel System ³ System ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Cabriolet
³ 15 ³ 1.8L ³ 2H ³ Digifant II MFI ³ Hall Effect³
³
³ ³ 8-Valve ³ ³ (1) ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Corrado SLC
³ 50 ³ 2.8L VR6³ AAA ³ Motronic MFI (3)³ Hall Effect³
³
³ ³ (2) ³ ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ´
³ EuroVan
³ 70 ³ 2.5L ³ AAF ³ Digifant MFI ³ Hall Effect³
³
³ ³10-Valve ³ ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Fox
³ 30 ³ 1.8L ³ ABG ³ Digifant II MFI ³ Hall Effect³
³
³ ³ 8-Valve ³ ³ (1) ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Golf
³ 1H ³ 2.0L ³ ABA ³ Motronic MFI (3)³ Hall Effect³
³
³ ³ 8-Valve ³ ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ´
³ GTI
³ 1H ³ 2.0L ³ ABA ³ Motronic MFI (3)³ Hall Effect³
³
³ ³ 8-Valve ³ ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Jetta
³ 1H ³ 2.0L ³ ABA ³ Motronic MFI (3)³ Hall Effect³
³
³ ³ 8-Valve ³ ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Passat GL
³ 31 ³ 2.0L ³ 9A ³ CIS-E Motronic ³ Hall Effect³
³
³ ³16-Valve ³ ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Passat GLX
³ 31 ³ 2.8L VR6³ AAA ³ Motronic MFI (3)³ Hall Effect³
³
³ ³ (2) ³ ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄ´
³(1) - California vehicles are equipped with Digifant I.
³
³(2) - The VR6 is a combination "Vee" and "Rheihenmotor" (German).
³
³ The combination can be roughly described as an "In-Line vee".
³
³ For practical purposes, engine has 6 in-line but slightly
³
³ staggered cylinders.
³
³(3) - Sequential Multiport Fuel Injection.
³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ VIN DEFINITION
Page 313 of 920

A - ENGINE/VIN ID
Article Text (p. 2)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
Numbers preceding the explanations in the legend below refer
to the sequence of characters as listed on VIN identification label.
(VIN) W V W C B 5 1 5 2 P C 0 0 0 0 0 1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
1-3 Indicates Nation of Origin.
4 Indicates Series.
5 Indicates Engine Type.
6 Indicates Restraint System.
7-8 Indicates Body Code.
9 Indicates Check Digit.
10 Indicates Model Year.
11 Indicates Assembly Plant.
12-17 Indicates Production Sequence.
MODEL YEAR VIN CODE APPLICATION TABLEÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄVIN Code Model Year
L .................................... 1990
M .................................... 1991
N .................................... 1992
P .................................... 1993
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ENGINE CODE LOCATIONFig. 1: Engine Code Location (4-Cylinder & 5-Cylinder)
Courtesy of Volkswagen United States, Inc.
Page 314 of 920

A - ENGINE/VIN ID
Article Text (p. 3)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PMFig. 2: Engine Code Location (V6)
Courtesy of Volkswagen United States, Inc.
END OF ARTICLE
Page 315 of 920

A/C COMPRESSOR OIL CHECKING
Article Text
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
ARTICLE BEGINNING
1993 GENERAL SERVICING
Compressor Refrigerant Oil Checking
* PLEASE READ THIS FIRST *
NOTE: For compressor applications, see COMPRESSOR APPLICATIONS
TABLE below. DO NOT exceed A/C system refrigerant oil
capacity, when servicing system. See REFRIGERANT OIL &
REFRIGERANT SPECIFICATIONS TABLE.
COMPRESSOR APPLICATION
NOTE: Due to late changes, always refer to underhood A/C
specification label in engine compartment or A/C compressor
label while servicing A/C system. If A/C Specification label
and specifications in this article differ, always use label
specifications.
COMPRESSOR APPLICATION TABLEÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄApplication Compressor
Acura .......................................... Nippondenso 10-Cyl.
Audi
90 ................................................... Zexel 6-Cyl.
100 .................................................. Zexel 6-Cyl.
BMW .................................................... Nippondenso
Or Seiko-Seiki
Chrysler Motors/Eagle
Colt & Summit ................................ Sanden FX105V Scroll
Colt Vista & Summit Wagon .............. Nippondenso 10PA15 10-Cyl.
Stealth ..................................... Sanden FX105VS Scroll
Ram-50 ......................................... Sanden FX80 Scroll
Ford Motor Co.
Capri ......................................... Nippondenso 10-Cyl.
Festiva ........................................ Nippondenso 6-Cyl.
General Motors & Geo
LeMans ......................................... Harrison V5 5-Cyl.
Metro & Tracker ............................... Nippondenso 10-Cyl.
Prizm .................................. Nippondenso 10PA15 10-Cyl.
Storm ............................... Diesel Kiki KC-50 Rotary Vane
Honda
Accord ........................................ Nippondenso 10-Cyl.
Or Hadsys RC-17S 7-Cyl.
Civic ............................................... Sanden Scroll
Civic Del Sol ....................................... Sanden Scroll
Prelude ............................................. Sanden Scroll
Hyundai
Elantra ..................................... Sanden TRF-090 Scroll
Page 316 of 920

A/C COMPRESSOR OIL CHECKING
Article Text (p. 2)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
Excel ........................................ Sanden SD-709 7-Cyl.
Scoupe ................................ Nippondenso 10PA15C 10-Cyl.
Sonata ......................................... Ford FX-15 10-Cyl.
Infiniti
G20 ................................... Atsugi NVR 140S Rotary Vane
J30 ............................................ Calsonic V6 6-Cyl.
Q45 ............................................ Calsonic V5 5-Cyl.
Isuzu (R-12)
Amigo ................................. Diesel Kiki DKS-13CH 6-Cyl.
Pickup
4-Cylinder ............................ Diesel Kiki DKS-13CH 6-Cyl.
V6 ...................................... Harrison R4 4-Cyl. Radial
Stylus ............................ Diesel Kiki DKV-14D Rotary Vane
Rodeo
4-Cylinder ............................ Diesel Kiki DKS-17CH 6-Cyl.
V6 ................................ Diesel Kiki DKV-14D Rotary Vane
Trooper ........................... Diesel Kiki DKV-14D Rotary Vane
Isuzu (R-134a Option) (1)
Amigo, Pickup, Rodeo & Trooper
2.3L & 2.6L Engine ............................ Zexel R-134a 6-Cyl.
3.1L Engine ..................... Harrison R-134a R-4 4-Cyl. Radial
3.2L Engine .............................. Zexel R-134a Rotary Vane
Jaguar
XJS .......................................... Sanden SD-709 7-Cyl.
XJ6 ......................................... Sanden SD-7H15 7-Cyl.
Lexus ................................... Nippondenso 10PA20 10-Cyl.
Mazda
B2200 & B2600i ...................................... Sanden 5-Cyl.
Miata ................................ Nippondenso TV12 Rotary Vane
MPV ........................................... Nippondenso 10-Cyl.
MX-6 & 626 .................................. Panasonic Rotary Vane
Navajo ......................................... Ford FX-15 10-Cyl.
MX-3, Protege & 323 ......................... Panasonic Rotary Vane
929 ......................................... Panasonic Rotary Vane
RX7 .................................. Nippondenso TV12 Rotary Vane
Mercedes-Benz
190E ................................... Nippondenso 10PA15 10-Cyl.
300D/E, 400E & 500E .................... Nippondenso 10PA17 10-Cyl.
300SE/SD, 400SE & 500SEL ............... Nippondenso 10PA20 10-Cyl.
Mitsubishi
Diamante
R-12 ........................................ Sanden FX105VS Scroll
R-134a .............................................. Sanden MSC105
Diamante Wagon ........................ Nippondenso 10PA17C 10-Cyl.
Galant & Mirage .............................. Sanden FX105V Scroll
Eclipse ................................ Nippondenso 10PA17 10-Cyl.
Expo/Expo LRV ......................... Nippondenso 10PA17C 10-Cyl.
Pickup ......................................... Sanden FX80 Scroll
Montero ................................ Nippondenso 10PA15 10-Cyl.
Precis ....................................... Sanden SD-709 7-Cyl.
3000GT
R-12 ........................................ Sanden FX105VS Scroll