recommended oil YAMAHA SR400 2016 Owners Manual

4-1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
For your safety – pre-operation checks
EAU63440
Inspect your vehicle each time you use it to make sure the vehicle is in safe oper-
ating condition. Always follow the in spection and maintenance procedures and
schedules described in the Owner’s Manual.
WARNING
EWA11152
Failure to inspect or maintain the vehicle properly increases the possibility
of an accident or equipment damage. Do not operate the vehicle if you find
any problem. If a problem cannot be corrected by the procedures provided
in this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
ITEM CHECKSPAGE
Fuel Check fuel level in fuel tank.
Refuel if necessary.
Check fuel line for leakage.
Check fuel tank breather hose
for obstructions, cracks or
damage, and check hose connection. 3-9, 3-10
Engine oil Check oil level in oil tank.
If necessary, add recommended oil to specified level.
Check vehicle for oil leakage. 6-9
Front brake Check operation.
If soft or spongy, have Yamaha dealer bleed hydraulic
system.
Check lever free play.
Adjust if necessary.
Check brake pads for wear.
Replace if necessary.
Check fluid level in reservoir.
If necessary, add specified brak e fluid to specified level.
Check hydraulic system for leakage. 6-19,
6-22, 6-23
Rear brake Check operation.
Check pedal free play.
Adjust if necessary. 6-20,
6-22
Clutch Check operation.
Lubricate cable if necessary.
Check lever free play.
Adjust if necessary. 6-18
Throttle grip Make sure that operation is smooth.
Check throttle grip free play.
If necessary, have Yamaha dealer adjust throttle grip
free play and lubricate cable and grip housing. 6-14,
6-27
Control cables Make sure that operation is smooth.
Lubricate if necessary. 6-27
2RD-28199-E1.book 1 ページ ２０１５年９月３日　木曜日　午後３時４２分

Periodic maintenance and adjustment
6-10
1
2
3
4
5
6
7
8
9
10
11
12
13
14 4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Install the oil filler cap.
To change the engine oil (with or
without oil filter element replace-
ment) 1. Start the engine, warm it up for several minutes, and then turn it
off.
2. Place an oil pan under the engine to collect the used oil.
3. Remove the oil filter element cover bleed bolt and its gasket, and the
oil filter element drain bolt to drain
the oil from the oil filter element
chamber. 4. Remove the engine oil drain bolt
and its gasket to drain the oil from
the crankcase.
5. Remove the engine oil filler cap, the engine oil tank drain bolt and
its gasket to drain the oil from the
oil tank.
1. Engine oil filler cap
2. Dipstick
3. Maximum level mark
4. Minimum level mark
3
4
1
2
1. Oil filter element cover bleed bolt
2. Gasket
3. Oil filter element drain bolt
1. Gasket
2. Engine oil drain bolt (crankcase)
1
2
3
21
2RD-28199-E1.book 10 ページ ２０１５年９月３日　木曜日　午後３時４２分

Periodic maintenance and adjustment
6-12
1
2
3
4
5
6
7
8
9
10
11
12
13
14 12. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler cap.
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.
NOTICE
ECA11621
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
Make sure that no foreign mate-
rial enters the crankcase.
13. Start the engine, and then let it idle for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
14. Turn the engine off, and then check the oil level and correct it if necessary.
NOTICE
ECA11232
After changing the engine oil, make
sure to check the oil pressure as de-
scribed below.
Loosen the bleed bolt.
Start the engine and keep it
idling until oil flows out. If no oil
comes out after one minute,
turn the engine off immediately
so it will not seize. If this occurs,
have a Yamaha dealer repair the
vehicle.
After checking the oil pressure,
tighten the bleed bolt to the
specified torque.
Tightening torques:
Engine oil drain bolt (crankcase):
30 Nm (3.0 m·kgf, 22 ft·lbf)
Engine oil drain bolt (oil tank): 16 Nm (1.6 m·kgf, 12 ft·lbf)
Recommended engine oil: See page 8-1.
Oil quantity:
Oil change:2.00 L (2.11 US qt, 1.76 Imp.qt)
With oil filter removal:
2.10 L (2.22 US qt, 1.85 Imp.qt)
1. Bleed bolt
Tightening torque:Bleed bolt:
18 Nm (1.8 m·kgf, 13 ft·lbf)
1
2RD-28199-E1.book 12 ページ ２０１５年９月３日　木曜日　午後３時４２分

8-1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Specifications
EAU69993Dimensions:
Overall length: 2085 mm (82.1 in)
Overall width: 750 mm (29.5 in)
Overall height:
1095 mm (43.1 in)
Seat height: 785 mm (30.9 in)
Wheelbase: 1410 mm (55.5 in)
Ground clearance:
130 mm (5.12 in)
Minimum turning radius: 2.4 m (7.87 ft)
Weight:
Curb weight:
174 kg (384 lb)
Engine:
Combustion cycle:4-stroke
Cooling system:
Air cooled
Valve train: SOHC
Number of cylinders: Single cylinder
Displacement:
399 cm
3
Bore  stroke:
87.0  67.2 mm (3.43  2.65 in)
Compression ratio: 8.5 : 1
Starting system:
Kickstarter
Lubrication system: Dry sump
Engine oil:
Recommended brand:
YAMALUBE
SAE viscosity grades: 10W-40
Recommended engine oil grade:
API service SG type or higher, JASO stan-
dard MA
Engine oil quantity:
Oil change:2.00 L (2.11 US qt, 1.76 Imp.qt)
With oil filter removal:
2.10 L (2.22 US qt, 1.85 Imp.qt)
Air filter:
Air filter element:Oil-coated paper element
Fuel:
Recommended fuel:
Regular unleaded gasoline (Gasohol [E10]
acceptable)
Fuel tank capacity:
12 L (3.2 US gal, 2.6 Imp.gal)
Fuel reserve amount: 2.2 L (0.58 US gal, 0.48 Imp.gal)
Fuel injection:
Throttle body:
ID mark: 2RD1 00
Spark plug(s):
Manufacturer/model:NGK/BPR6ES
Spark plug gap: 0.7–0.8 mm (0.028–0.031 in)
Clutch:
Clutch type:Wet, multiple-disc
Drivetrain:
Primary reduction ratio:
2.567 (77/30)
Final drive: Chain
Secondary reduction ratio: 2.947 (56/19)
Transmission type:
Constant mesh 5-speed
Gear ratio: 1st:
2.357 (33/14)
2nd: 1.556 (28/18)
3rd: 1.190 (25/21)
4th: 0.917 (22/24)
5th: 0.778 (21/27)
Chassis:
Frame type:Semi double cradle
Caster angle: 27.7 
Trail:
111 mm (4.4 in)
2RD-28199-E1.book 1 ページ ２０１５年９月３日　木曜日　午後３時４２分