light YAMAHA TRICITY 2017 Owner's Manual

Periodic maintenance and adjustment
6-33
6
EAU61170
Turn signal light bulb
If a turn signal light does not come on,
have a Yamaha dealer check its electri-
cal circuit or replace the bulb.
EAUM3510
Replacing the license plate
light bulb
1. Remove the license plate light unit
by removing the screw.
2. Remove the license plate light
bulb socket (together with the
bulb) by pulling it out.
3. Remove the burnt-out bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with
the bulb) by pushing it in.
6. Install the license plate light unit by
installing the screw.
1. License plate light unit
2. Screw
1. License plate light bulb socket
1
2
1
UBR7E0E0.book Page 33 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-34
6
EAU60701
Troubleshooting
Although Yamaha vehicles receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your vehicle re-
quire any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the vehicle prop-
erly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
WARNING
EWA15142
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from water
heaters or furnaces. Gasoline or
gasoline vapors can ignite or ex-
plode, causing severe injury or prop-
erty damage.
UBR7E0E0.book Page 34 Tuesday, October 25, 2016 2:44 PM

Vehicle care and storage
7-2
7 structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.
zImproper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinse
off any detergent residue using
plenty of water, as it is harmful
to plastic parts.
zDo not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake fluid,
antifreeze or electrolyte.
zDo not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
zFor vehicles equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaningcompounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quality
plastic polishing compound
af-
ter washing.
NOTICE
ECAU0061
Use care when cleaning the radiator.
High-pressure washers may dam-
age the radiator fins. Do not spray
the radiator fins at an angle, and al-
ways keep the nozzle at least 50 cm
(20 in) away from the spins when
spraying.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea, or
on salt-sprayed roads
Since sea salt or salt sprayed on roads
during winter are extremely corrosive
in combination with water, carry out
the following steps after each ride in
the rain, near the sea, or on salt-
sprayed roads.
TIP
Salt sprayed on roads in the winter
may remain well into spring.
UBR7E0E0.book Page 2 Tuesday, October 25, 2016 2:44 PM

Vehicle care and storage
7-3
71. Clean the vehicle with cold water
and a mild detergent after the en-
gine has cooled down. NOTICE:
Do not use warm water since it
increases the corrosive action
of the salt.
[ECA10792]
2. Apply a corrosion protection spray
on all metal, including chrome-
and nickel-plated, surfaces to pre-
vent corrosion.
Cleaning the windshield
Avoid using any alkaline or strong acid
cleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield
with a cloth or sponge dampened with
a mild detergent, and then wash it off
thoroughly with water. For additional
cleaning, use Yamaha Windshield
Cleaner or another high-quality wind-
shield cleaner. Some cleaning com-
pounds for plastics may leave
scratches on the windshield. Before
using such cleaners, test an area of the
windshield which does not affect your
visibility and which cannot be easily
recognized.
After cleaning
1. Dry the vehicle with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum, and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed surfaces.
4. Use spray oil as a universal clean-
er to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the vehicle dry completely be-
fore storing or covering it.WARNING
EWA17830
Contaminants on the brakes or tires
can cause loss of control.
zMake sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires with
warm water and a mild deter-
gent.
zBefore operating the vehicle
test its braking performance
and cornering behavior.
NOTICE
ECAU0022
zApply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
zNever apply oil or wax to any
rubber parts, plastic parts or
headlight, taillight and meter
lenses, but treat them with a
suitable care product.
zAvoid using abrasive polishing
compounds as they will wear
away the paint.
UBR7E0E0.book Page 3 Tuesday, October 25, 2016 2:44 PM

Vehicle care and storage
7-4
7
TIP
zConsult a Yamaha dealer for ad-
vice on what products to use.
zWashing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.
EAU60721
Storage
Short-term
Always store your vehicle in a cool, dry
place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the vehi-
cle.
NOTICE
ECA21170
zStoring the vehicle in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
zTo prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your vehicle for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
UBR7E0E0.book Page 4 Tuesday, October 25, 2016 2:44 PM

Specifications
8-2
8
Track:
385 mm (15.2 in)
Front tire:
Type:
Tubeless
Size:
90/80-14M/C 43P
Manufacturer/model:
IRC/SCT-003
Rear tire:
Type:
Tubeless
Size:
130/70-13M/C 63P
Manufacturer/model:
IRC/SCT-003
Loading:
Maximum load:
167 kg (368 lb)
(Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measured on cold
tires):
1 person:
Front:
200 kPa (2.00 kgf/cm², 29 psi)
Rear:
225 kPa (2.25 kgf/cm², 33 psi)
2 persons:
Front:
200 kPa (2.00 kgf/cm², 29 psi)
Rear:
225 kPa (2.25 kgf/cm², 33 psi)
Front wheel:
Wheel type:
Cast wheel
Rim size:
14M/C x MT2.15
Rear wheel:
Wheel type:
Cast wheel
Rim size:
13M/C x MT3.50
Unified brake system:
Operation:
Activated by rear brake
Front brake:
Type:
Hydraulic disc brakeSpecified brake fluid:
DOT 4
Rear brake:
Type:
Hydraulic disc brake
Specified brake fluid:
DOT 4
Front suspension:
Type:
Telescopic fork
Spring:
Coil spring
Shock absorber:
Hydraulic damper
Wheel travel:
90 mm (3.5 in)
Rear suspension:
Type:
Unit swing
Spring:
Coil spring
Shock absorber:
Hydraulic damper
Wheel travel:
90 mm (3.5 in)
Electrical system:
System voltage:
12 V
Ignition system:
TCI
Charging system:
AC magneto
Battery:
Model:
YTZ7V
Voltage, capacity:
12 V, 6.0 Ah (10 HR)
Bulb wattage:
Headlight:
LED
Brake/tail light:
LED
Front turn signal light:
10.0 W
Rear turn signal light:
10.0 W
Auxiliary light:
LED
License plate light:
5.0 W
UBR7E0E0.book Page 2 Tuesday, October 25, 2016 2:44 PM

Specifications
8-3
8
Meter lighting:
LED
High beam indicator light:
LED
Turn signal indicator light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
ABS warning light:
LED (MWS125-A)
Fuse(s):
Main fuse:
15.0 A
Main fuse 2:
7.5 A
Terminal fuse 1:
2.0 A
Signaling system fuse:
7.5 A
ABS control unit fuse:
7.5 A (MWS125-A)
ABS motor fuse:
30.0 A (MWS125-A)
ABS solenoid fuse:
30.0 A (MWS125-A)
UBR7E0E0.book Page 3 Tuesday, October 25, 2016 2:44 PM

10-1
10
Index
A
ABS (for ABS models) ........................... 3-11
ABS warning light (for ABS models) ....... 3-4
Acceleration and deceleration ................ 5-3
Accessory box ...................................... 3-17
Air filter and V-belt case air filter
elements ............................................. 6-14
Auxiliary DC connector ......................... 3-22
Auxiliary DC jack ................................... 3-21
Auxiliary lights ....................................... 6-32
B
Battery .................................................. 6-28
Brake fluid, changing ............................ 6-23
Brake fluid level, checking .................... 6-22
Brake lever, front .................................. 3-10
Brake lever, rear.................................... 3-10
Brake levers, lubricating ....................... 6-25
Brake/tail light ....................................... 6-32
Braking.................................................... 5-3
C
Cables, checking and lubricating ......... 6-24
Care ........................................................ 7-1
Catalytic converter ................................ 3-14
Centerstand and sidestand,
checking and lubricating .................... 6-25
Coolant ................................................. 6-12
Coolant temperature warning light ......... 3-3
D
Data recording, vehicle ........................... 9-2
Diagnostic connector.............................. 9-2
Dimmer switch ........................................ 3-9
E
Eco indicator light ................................... 3-3
Engine break-in....................................... 5-4
Engine oil and oil strainer........................ 6-9
Engine serial number .............................. 9-1
Engine trouble warning light ................... 3-3
F
Final transmission oil ............................ 6-11
Front and rear brake pads, checking.... 6-21
Front brake lever free play, checking ... 6-20
Front fork, checking .............................. 6-26
Fuel ....................................................... 3-12
Fuel consumption, tips for reducing ....... 5-4
Fuel tank cap ........................................ 3-12
Fuel tank overflow hose ........................ 3-14
Fuses, replacing.................................... 6-30
H
Handlebar switches ................................ 3-9
Headlight............................................... 6-31High beam indicator light ....................... 3-3
Horn switch ............................................ 3-9
I
Identification numbers ............................ 9-1
Ignition circuit cut-off system............... 3-19
Indicator lights and warning lights ......... 3-3
K
Keyhole shutter ...................................... 3-2
L
Leaning system, checking .................... 6-28
License plate light bulb, replacing........ 6-33
Luggage hook ...................................... 3-18
M
Main switch/steering lock....................... 3-1
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission control
system.................................................. 6-3
Matte color, caution ............................... 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-5
P
Panel, removing and installing ............... 6-7
Parking ................................................... 5-5
Part locations ......................................... 2-1
Passenger footrest ............................... 3-15
R
Rear brake lever free play, checking .... 6-20
S
Safe-riding points ................................... 1-6
Safety information .................................. 1-1
Seat ...................................................... 3-15
Sidestand ............................................. 3-18
Spark plug, checking ............................. 6-8
Specifications ......................................... 8-1
Starting off.............................................. 5-2
Starting the engine ................................. 5-1
Start switch ............................................ 3-9
Steering, checking................................ 6-26
Steering tie rod, checking .................... 6-27
Storage ................................................... 7-4
Storage compartment .......................... 3-16
T
Throttle grip and cable,
checking and lubricating .................... 6-24
Throttle grip free play, checking........... 6-16
Tires ...................................................... 6-17
Tool kit.................................................... 6-2
Troubleshooting ................................... 6-34
Troubleshooting charts ........................ 6-35
Turn signal indicator lights ..................... 3-3
UBR7E0E0.book Page 1 Tuesday, October 25, 2016 2:44 PM

Index
10-2
10
Turn signal light bulb ............................ 6-33
Turn signal switch .................................. 3-9
V
Valve clearance .................................... 6-17
V-belt, checking ................................... 6-23
Vehicle identification number ................. 9-1
W
Wheel bearings, checking .................... 6-27
Wheels.................................................. 6-19
UBR7E0E0.book Page 2 Tuesday, October 25, 2016 2:44 PM