bulb ACURA CSX 2006 Service Owner's Manual




(#'


 )
Headlight Front Side Marker Light
Headlight (High Beam): 60 W
Headlight (Low Beam) : 51 W
Without HID
High
Low Front Side Marker Light: 2 CP
22-177
Bulb Replacement
A
A
1. For low beam : Remove the inner fender (see page
20-171).: Without HID
2. Disconnect the 2P connector (A) from the headlight.
:
3. Turn the bulb socket 45 ° counterclockwise to remove the bulb.
4. Install a new bulb in the reverse order of removal. 1. Remove the inner fender (see page 20-171).
2. Disconnect the 2P connector (A) from the front side
marker light.
3. Turn the bulb socket 45 ° counterclockwise to remove the bulb.
4. Install a new bulb in the reverse order of removal.
(cont’d)
08/08/21 14:27:03 61SNR030_220_0179
ProCarManuals.com
DYNOMITE -2009-


Front Parking LightFront Turn Signal Light
Front Parking Light: 3 CP Front Turn Signal Light: 24/2.2 CP
22-178Exterior Lights
Bulb Replacement (cont’d)
A
A
1. Disconnect the 2P connector (A) from the front
parking light.
2. Turn the bulb socket 45 ° counterclockwise to remove the bulb.
3. Install a new bulb in the reverse order of removal. 1. Disconnect the 3P connector (A) from the front turn
signal light.
2. Turn the bulb socket 45 ° counterclockwise to remove the bulb.
3. Install a new bulb in the reverse order of removal.
08/08/21 14:27:03 61SNR030_220_0180
ProCarManuals.com
DYNOMITE -2009-


(#'



 ) 
(#'



 )
Brake Lights/Taillights: 21/5 W
Rear Turn Signal Light: 21 W
Rear Side Marker Light: 3 CP
Taillight: 5 W
Back-up Light: 16 W
22-17922-179
Taillight Replacement
Inner Taillight Replacement
A
B A
B
1. Remove the rear bumper (see page 20-149).
2. Disconnect the connectors (A) from the ta
illights (B).
3. Turn the bulb sockets 45 ° counterclockwise to remove the bulbs.
4. Remove the nuts and screws, then remove the taillight.
5. Install the taillight in the reverse order of removal. 1. Remove the trunk lid trim (see page 20-82).
2. Disconnect the connectors (A) from the inner
taillight (B).
3. Turn the bulb sockets 45 ° counterclockwise to remove the bulbs.
4. Remove the nuts, then remove the taillight.
5. Install the inner taillight in the reverse order of removal.
08/08/21 14:27:41 61SNR030_220_0181
ProCarManuals.com
DYNOMITE -2009-


(#'

 ) 

(#'



 )
License Plate Light: 5 W
High Mount Brake Light: 21 W
Except TYPE S model
22-18022-180Exterior Lights
License Plate Light Replacement High Mount Brake Light
Replacement
A
B
C
A
B
C
A
1. Open the trunk lid, and remove the rear license trim (see page 20-168).
2. Disconnect the 2P connector (A) from the license plate light.
3. Release the bulb socket (B) from the lens (C) by pressing on the tabs.
4. Remove the lens from the trunk lid by pressing on the tabs.
5. Install the license plate light in the reverse order of removal. 1. Open the trunk lid.
2. Disconnect the 2P connector (A) from the high
mount brake light.
3. Turn the bulb socket (B) 45 ° counterclockwise to remove the bulb (C).
4. Remove the rear shelf (see page 20-78).
5. Remove the high mount brake light (A).
6. Install the high mount brake light in the reverse order of removal.
08/08/21 14:27:41 61SNR030_220_0182
ProCarManuals.com
DYNOMITE -2009-

Cavity Wire Test conditionTest: Desired result Possible cause if result desired is
not obtained
22-190Turn Signal/Hazard Warning Lights
MICU Input Test (cont’d)
5. With the connectors still disconnected, do these input tests at the following connectors.
 If any test indicates a problem, find and correct the cause, then recheck the system.
 If all the input tests prove OK, go to step 6.
























E39 BRN Under all conditions Connect terminals G2 and E39
with a jumper wire:
The right rear turn signal light
should come on.Poor ground (G701)
Blown bulb
An open in the wire
E40 BLU Under all conditions Connect terminals G2 and E40 with a jumper wire:
The left rear turn signal light
should come on.Poor ground (G701)
Blown bulb
An open in the wire
F1 BRN Under all conditions Connect terminals G2 and F1 with a jumper wire:
The right front turn signal light
should come on.Poor ground (G201)
Blown bulb
An open in the wire
G1 BLU Under all conditions Connect terminals G2 and G1 with a jumper wire:
The left front turn signal light
should come on.Poor ground (G301)
Blown bulb
An open in the wire
M1 BLU Under all conditions Connect terminals G2 and M1 with a jumper wire:
The left side turn signal light
should come on.Poor ground (G503)
Blown LED
An open in the wire
M2 GRN Under all conditions Connect terminals G2 and M2 with a jumper wire:
The right side turn signal light
should come on.Poor ground (G502)
Blown LED
An open in the wire
P1 GRN Under all conditions Connect terminals G2 and P1 with a jumper wire:
The right turn signal indicator
should come on.Poor ground (G504)
Faulty gauge control module
(speedo)
An open in the wire
P6 BLU Under all conditions Connect terminals G2 and P6 with a jumper wire:
The left turn signal indicator
should come on.Poor ground (G504)
Faulty gauge control module
(speedo)
An open in the wire
08/08/21 14:27:44 61SNR030_220_0192
ProCarManuals.com
DYNOMITE -2009-



(#'


) 

(#'
 )
22-19222-192 Turn Signal/Hazard Warning Lights
Hazard Warning Switch Test/
Replacement
Side Turn Signal Light Replacement
A
A
Terminal
Position 12
4
5
OFF ON A
A
B
1. Remove the center panel.  With audio:– ’06-08 models (see page 23-80)
– ’09 model (see page 23-256)
 With navigation: – ’06-08 models (see page 23-155)
– ’09 model (see page 23-355)
2. Remove the screws and the hazard warning switch (A).
3. Check for continuity between the terminals in each switch position according to the table.
4. If the continuity is not as specified, replace the bulb (A) or the hazard warning switch.
5. Install the hazard warning switch in the reverse order of removal. 1. Remove the mirror holder (see page 20-34).
2. Remove the four screws and the mirror visor (A).
3. Disconnect the 2P connector (A) from the side turn
signal light (B), then remove the side turn signal
light.
4. Install the side turn signal light in the reverse order of removal.
08/08/21 14:27:45 61SNR030_220_0194
ProCarManuals.com
DYNOMITE -2009-

Î

(#'
)
 Î

(#'
)

With moonroof Without moonroof
Front Individual Map Light: 8 W x 2 Front Individual Map Light: 8 W x 2
22-19622-196Interior Lights
Front Individual Map Light Test/Replacement
A
B
C
Position 13
Terminal
RIGHT LEFT ON
OFF ON
OFF Body
ground A
B
C
Position 1
Terminal
RIGHT LEFT ON
OFF ON
OFF Body
ground
1. Turn the map light switch OFF.
2. Carefully pry the lens (A) off with a small
screwdriver.
3. Remove the screws, then remove the map lights (B) and moonroof switch or navigation microphone (C).
4. Disconnect the 3P connector from the map lights and the 10P connector from the moonroof switch or
navigation microphone.
5. Check for continuity between the terminals in each switch position according to the table.
6. If the continuity is not as specified, check the bulb(s). If the bulb(s) are OK, replace the light
assembly.
7. Install the map light in the reverse order of removal. 1. Turn the map light switch OFF.
2. Carefully pry the lens (A) off with a small
screwdriver.
3. Remove the screws, then remove the map lights (B).
4. Disconnect the 3P connector (C) from the map lights.
5. Check for continuity between the terminals in each switch position according to the table.
6. If the continuity is not as specified, check the bulb(s). If the bulb(s) are OK, replace the light
assembly.
7. Install the map light in the reverse order of removal.
08/08/21 14:27:50 61SNR030_220_0198
ProCarManuals.com
DYNOMITE -2009-


(#'

)
 ´
µ 
(#'
)
´ µ
Ceiling Light: 8 W Trunk Light: 5 W
22-19722-197
Ceiling Light Test/Replacement Trunk Light Test/Replacement
AC
B A
B
() ()
1. Turn the ceiling light switch OFF.
2. Carefully pry the lens (A) off with a small
screwdriver.
3. Remove the screws, then remove the ceiling light (B).
4. Disconnect the 3P connector (C) from the ce iling
light.
5. Check for continuity between the terminals.  There should be continuity between terminalsNo. 1 and No. 2 with the switch in the MIDDLE
position.
 There should be continuity between terminals No. 2 and No. 3 (Body ground) with the switch in
the ON position.
 There should be no continuity between terminals No. 1 and No. 2, and between No. 2 and body
ground with the switch in the OFF position.
6. If the continuity is not as specified, check the bulb. If the bulb is OK, replace the light.
7. Install the ceiling light in the reverse order of removal. 1. Open the trunk lid.
2. Carefully pry out the trunk light (A).
3. Disconnect the 2P connector (B) from the light.
4. Check for continuity between terminals No. 1 ( )
and No. 2 ( ). There should be continuity. If there
is no continuity, check the bulb. If the bulb is OK,
replace the trunk light assembly.
5. Install the trunk light in the reverse order of removal.
08/08/21 14:27:50 61SNR030_220_0199
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
) 
(#'

 ) Courtesy light: 3.4 W
22-19822-198
Interior Lights
Ambient Light Test/Replacement Courtesy Light Replacement
A
B
C ’06-07 models
’08-09 models
A
B C
D
1. Remove the front individual map light.
 With moonroof (see page 22-196)
 Without moonroof (see page 22- 196)
2. Disconnect the 10P (or 12P ) connector (A) from the ambient light (B), then remove the ambient
light from the front individual map light housing (C).
1: ’06-07 models
2: ’08-09 models
3. Connect battery power to the terminal No. 5 and ground to the No. 3 terminal. The ambient light
should turn on. If the light does not turn on, replace
the ambient light.
4. Install the ambient light in the reverse order of removal. 1. Carefully pry off the lens (A) with a small
screwdriver.
2. Pry out the housing (B) from the door panel, then disconnect the 2P connector (C).
3. Separate the housing, then remove the bulb (D) from the socket.
4. Install the courtesy light in the reverse order of removal.
12
08/08/21 14:27:50 61SNR030_220_0200
ProCarManuals.com
DYNOMITE -2009-


(#'


) 
(#'

)
Glove Box Light: 3.4 W
Vanity Mirror Light: 2 W
’08-09 models
22-19922-199
Glove Box Light Test/Replacement Vanity Mirror Light Test/Replacement
B
A C
A B
C
1. Open the glove box.
2. Remove the screws, then disconnect the 2P
connector from the glove box light (A).
3. Check for continuity between terminals No. 1 and No. 2.
 There should be continuity with the switch (B) released.
 There should be no continuity with the switch (B) pushed.
4. If the continuity is not as specified, check the bulb (C). If the bulb is OK, replace the light.
5. Install the glove box light in the reverse order of removal. 1. Open the sunvisor.
2. Remove the sunvisor (see page 20-84).
3. Disconnect the 2P connector (A) from the vanity
mirror light.
4. Check for continuity between terminals No. 1 and No. 2.
 With the vanity mirror cover (B) opened, there should be continuity.
 With the vanity mirror cover closed, there should be no continuity.
5. If the continuity is not as specified, replace the bulb (C) or the sunvisor.
6. Install the vanity mirror light in the reverse order of removal.
08/08/21 14:27:51 61SNR030_220_0201
ProCarManuals.com
DYNOMITE -2009-