ACURA CSX 2006 Service Repair Manual

OBD Status
11-8Fuel and Emissions Systems
General Troubleshooting Information (cont’d)
13. Do the battery installation procedure (see page
22-69).
14. Turn the ignition switch to ON (II). NOTE: DTC P0630 VIN Not Programmed or
Mismatch may be stored because the VIN has not
been programmed into the ECM/PCM; ignore it,
and continue this procedure.
15. Manually input the VIN to the ECM/PCM with the HDS.
16. Select the IMMOBI SYSTEM with the HDS.
17. Enter the immobilizer code that you got from the iN, or use the ECM/PCM replacement procedure in the
HDS; this allows you to start the engine.
18. Reset the ECM/PCM with the HDS.
19. If the TP POSITION CHECK failed in step 5, clean the throttle body (see page 11- 344).
20. Update the ECM/PCM if it does not have the latest software (see page 11-227).
21. Do the ECM/PCM idle learn procedure (see page 11-310).
22. Do the CKP pattern clear/CKP pattern learn procedure. The OBD status shows the current system status of
each DTC and all of the parameters. This function is
used to see if the repair was successfully completed.
The results of diagnostic tests for the DTC are displayed
as:
 PASSED: The on board diagnosis is successfully finished.
 FAILED: The on board diagnosis has finished but failed.
 EXECUTING: The vehicle is in enable criteria conditions for the DTC and the on board diagnosis is
running.
 NOT COMPLETED: The on board diagnosis was running but is out of the enable conditions of the DTC.
 OUT OF CONDITION: The vehicle has stayed out of the enable conditions for the DTC.
08/08/21 14:12:35 61SNR030_110_0008
ProCarManuals.com
DYNOMITE -2009-

•••Ó
Ó
•••
•••
•••
••• Ó
•••
••• Ó
•••
•••
•••
••• Ó
Ó
Ó
Ó
•••
••• Ó
••• ÓÓ
••• Ó
Ó
•••
••• Ó
Ó
Ó
Ó
Ó
(#')
DTC
(MIL indication ) Two Drive Cycle
Detection Detection Item MIL Note
11-9
DTC Troubleshooting Index
P0010 (56)
Variable Valve Timing Control (VTC) Oil Control Solenoid Valve
Malfunction ON (see page 11-274)
P0011 (56) Variable Valve Timing Control (VTC) System Malfunction ON (see page 11-276)
P0101 (50) Mass Air Flow (MAF) Sensor Circuit Range/Performance Problem ON (see page 11-74)
P0102 (50) Mass Air Flow (MAF) Sensor Circuit Low Voltage ON (see page 11-75)
P0103 (50) Mass Air Flow (MAF) Sensor Circuit High Voltage ON (see page 11-78)
P0107 (3) Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage ON (see page 11-80)
P0108 (3) Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage ON (see page 11-82)
P0111 (10) Intake Air Temperature (IAT) Sensor Circuit Range/Performance
Problem ON (see page 11-85)
P0112 (10) Intake Air Temperature (IAT) Sensor Circuit Low Voltage ON (see page 11-86)
P0113 (10) Intake Air Temperature (IAT) Sensor Circuit High Voltage ON (see page 11-87)
P0116 (86) Engine Coolant Temperature (ECT) Sensor 1 Circuit Range/
Performance Problem ON (see page 11-90)
P0117 (6) Engine Coolant Temperature (ECT) Sensor 1 Circuit Low Voltage ON (see page 11-91)
P0118 (6) Engine Coolant Temperature (ECT) Sensor 1 Circuit High Voltage ON (see page 11-92)
P0122 (7) Throttle Position (TP) Sensor A Circuit Low Voltage ON (see page 11-232)
P0123 (7) Throttle Position (TP) Sensor A Circuit High Voltage ON (see page 11-234)
P0125 (86) Engine Coolant Temperature (ECT) Sensor 1 Malfunction/Slow
Responce ON (see page 11-95)
P0128 (87) Cooling System Malfunction ON (see page 11-96)
P0133 (61) Air Fuel Ratio (A/F) Sensor (Sensor 1) Malfunction/Slow Response ON (see page 11-97)
P0134 (41) Air Fuel Ratio (A/F) Sensor (Sensor 1) Heater System Malfunction ON (see page 11-98)
P0135 (41) Air Fuel Ratio (A/F) Sensor (Sensor 1) Heater Circuit Malfunction ON (see page 11-99)
P0137 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit Low Voltage ON (see page 11-104)
P0138 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit High Voltage ON (see page 11-106)
P0139 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Slow Response ON (see page 11-109)
P0141 (65) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Heater Circuit Malfunction ON (see page 11-110)
P0171 (45) Fuel System Too Lean ON (see page 11-113)
P0172 (45) Fuel System Too Rich ON (see page 11-113)
P0222 (7) Throttle Position (TP) Sensor B Circuit Low Voltage ON (see page 11-236)
P0223 (7) Throttle Position (TP) Sensor B Circuit High Voltage ON (see page 11-239)
P0300 (75)
and any
combination of
the following:
P0301 (71)
P0302 (72)
P0303 (73)
P0304 (74) Random Misfire Detected
ON (see page 11-115)
P0301 (71) No. 1 Cylinder Misfire Detected ON (see page 11-118)
P0302 (72) No. 2 Cylinder Misfire Detected ON (see page 11-118)
P0303 (73) No. 3 Cylinder Misfire Detected ON (see page 11-118)
P0304 (74) No. 4 Cylinder Misfire Detected ON (see page 11-118)
NOTE:  The above DTCs are indicated when the PGM-FI system is selected with the HDS.
 Some automatic transmission DTCs cause the MIL to come on. If the MIL is on and no DTCs are indicated in the PGM-FI system, select the A/T system, and check for automatic transmission DTCs.
: These DTCs are indicated by a blinking MIL when the SCS line is jumped with the HDS.
4: K20Z2 engine
5: K20Z3 engine
(cont’d)
4
5 4
5
08/08/21 14:12:35 61SNR030_110_0009
ProCarManuals.com
DYNOMITE -2009-

•••
•••
•••
•••
•••
•••
•••
•••Ó
Ó
••• Ó
•••
Ó
••• Ó
••• ÓÓ
Ó
Ó
•••
•••
•••
••• Ó
Ó
Ó
•••
•••
Ó
Ó
Ó
Ó
•••
•••
•••
•••
•••
•••
DTC
(MIL indication ) Two Drive Cycle
Detection Detection Item MIL Note
11-10Fuel and Emissions Systems
DTC Troubleshooting Index (cont’d)
P0325 (23)
Knock Sensor Circuit Malfunction ON (see page 11-126)
P0335 (4) Crankshaft Position (CKP) Sensor No Signal ON (see page 11-128)
P0339 (4) Crankshaft Position (CKP) Sensor Circuit Intermittent Interruption ON (see page 11-131)
P0340 (57) Camshaft Position (CMP) Sensor A No Signal ON (see page 11-278)
P0341 (57) Camshaft Position (CMP) Sensor A and Crankshaft Position (CKP)
Sensor Incorrect Phase Detected ON (see page 11-281)
P0344 (57) Camshaft Position (CMP) Sensor A Circuit Intermittent Interruption ON (see page 11-282)
P0365 (8) Camshaft Position (CMP) Sensor B No Signal ON (see page 11-132)
P0369 (8) Camshaft Position (CMP) Sensor B Circuit Intermittent Interruption ON (see page 11-134)
P0401 (80) Exhaust Gas Recirculation (EGR) Insufficient Flow ON (see page 11-357)
P0404 (12) Exhaust Gas Recirculation (EGR) Valve Circuit Range/Performance
Problem ON (see page 11-358)
P0406 (12) Exhaust Gas Recirculation (EGR) Valve Position Sensor Circuit High
Voltage ON (see page 11-361)
P0420 (67) Catalyst System Efficiency Below Threshold ON (see page 11-353)
P0443 (92) Evaporative Emission (EVAP) Canister Purge Valve Circuit
Malfunction ON (see page 11-375)
P0451 (91) Fuel Tank Pressure (FTP) Sensor Circuit Range/Performance Problem ON (see page 11-379)
P0452 (91) Fuel Tank Pressure (FTP) Sensor Circuit Low Voltage ON (see page 11-380)
P0453 (91) Fuel Tank Pressure (FTP) Sensor Circuit High Voltage ON (see page 11-383)
P0455 (90) Evaporative Emission (EVAP) System Large Leak Detected ON (see page 11-386)
P0456 (90) Evaporative Emission (EVAP) System Very Small Leak Detected ON (see page 11-386)
P0457 (90) Evaporative Emission (EVAP) System Leak Detected/Fuel Fill Cap
Loose or Missing ON (see page 11-390)
P0457 (90) Evaporative Emission (EVAP) System Leak Detected/Fuel Fill Cap
Loose or Missing OFF (see page 11-390)
P0461 (121) Fuel Level Sensor (Fuel Gauge Sending Unit) Circuit Range/
Performance Problem OFF (see page 11-313)
P0462 (121) Fuel Level Sensor (Fuel Gauge Sending Unit) Circuit Low Voltage OFF (see page 11-313)
P0463 (121) Fuel Level Sensor (Fuel Gauge Sending Unit) Circuit High Voltage OFF (see page 11-315)
P0496 (92) Evaporative Emission (EVAP) System High Purge Flow Detected ON (see page 11-391)
P0497 (90) Evaporative Emission (EVAP) System Low Purge Flow Detected ON (see page 11-392)
P0497 (90) Evaporative Emission (EVAP) System Low Purge Flow Detected ON (see page 11-395)
P0498 (117) Evaporative Emission (EVAP) Canister Vent Shut Valve Circuit Low
Voltage ON (see page 11-398)
P0499 (117) Evaporative Emission (EVAP) Canister Vent Shut Valve Circuit High
Voltage ON (see page 11-401)
P0506 (14) Idle Control System RPM Lower Than Expected ON (see page 11-298)
P0507 (14) Idle Control System RPM Higher Than Expected ON (see page 11-300)
P050A (167) Cold Start Idle Air Control System Performance Problem ON (see page 11-135)
P050B (167) Cold Start Ignition Timing Control System Performance Problem ON (see page 11-137)
P0532 (191) A/C Pressure Sensor Circuit Low Voltage OFF (see page 11-301)
P0533 (191) A/C Pressure Sensor Circuit High Voltage OFF (see page 11-303)
P0562 (34) Charging System Low Voltage OFF (see page 11-140)
P0563 (34) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Power Source Circuit Unexpected Voltage OFF (see page 11-141)
P0602 (196) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Programming Error ON (see page 11-144)
P0603 (131) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Internal Control Module Keep Alive Memory (KAM) Error ON (see page 11-144)
NOTE:  The above DTCs are indicated when the PGM-FI system is selected with the HDS.
 Some automatic transmission DTCs cause the MIL to come on. If the MIL is on and no DTCs are indicated in the PGM-FI system, select the A/T system, and check for automatic transmission DTCs.
: These DTCs are indicated by a blinking MIL when the SCS line is jumped with the HDS.
4: K20Z2 engine
5: K20Z3 engine
6: ’06 model
7: ’07-09 models
8: ’06-08 models
4
4
4
6
7 6
7
4
5
4
5
8
08/08/21 14:12:35 61SNR030_110_0010
ProCarManuals.com
DYNOMITE -2009-

•••
•••
•••
•••Ó
•••
•••
•••
••• Ó
Ó
Ó
•••
••• Ó
•••
••• Ó
Ó
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
••• Ó
•••
•••
••• Ó
DTC
(MIL indication ) Two Drive Cycle
Detection Detection Item MIL Note
11-11
P0606 (0)
Engine Control Module (ECM)/Powertrain Control Module (PCM)
Processor Malfunction ON (see page 11-145)
P060A (131) Powertrain Control Module (PCM) (A/T System) Internal Control
Module Malfunction ON (see page 11-145)
P062F (131) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Internal Control Module Keep Alive Memory (KAM) Error ON (see page 11-144)
P0630 (139) VIN Not Programmed or Mismatch ON (see page 11-146)
P0685 (135) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Power Control Circuit/Internal Circuit Malfunction ON (see page 11-147)
P0720 (122) Output Shaft (Countershaft) Speed Sensor Circuit Malfunction ON (see page 11-148)
P0720 (122) Output Shaft (Countershaft) Speed Sensor Circuit Malfunction ON (see page 11-149)
P1009 (56) Variable Valve Timing Control (VTC) Advance Malfunction ON (see page 11-283)
P1109 (13) Barometric Pressure (BARO) Sensor Circuit Out of Range High ON (see page 11-152)
P1116 (86) Engine Coolant Temperature (ECT) Sensor 1 Circuit Range/
Performance Problem ON (see page 11-153)
P1128 (5) Manifold Absolute Pressure (MAP) Sensor Signal Lower Than
Expected ON (see page 11-155)
P1129 (5) Manifold Absolute Pressure (MAP) Sensor Signal Higher Than
Expected ON (see page 11-156)
P1157 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) AFS Circuit High Voltage ON (see page 11-157)
P1172 (61) Air Fuel Ratio (A/F) Sensor (Sensor 1) Circuit Out of Range High ON (see page 11-159)
P1297 (20) Electrical Load Detector (ELD) Circuit Low Voltage OFF (see page 11-160)
P1298 (20) Electrical Load Detector (ELD) Circuit High Voltage OFF (see page 11-162)
P1454 (91) Fuel Tank Pressure (FTP) Sensor Circuit Range/Performance Problem ON (see page 11-402)
P145C (90) Evaporative Emission (EVAP) System Purge Flow Malfunction ON (see page 11-404)
P1549 (34) Charging System High Voltage OFF (see page 11-164)
P1658 (40) Electronic Throttle Control System (ETCS) Control Relay ON
Malfunction ON (see page 11-241)
P1659 (40) Electronic Throttle Control System (ETCS) Control Relay OFF
Malfunction ON (see page 11-243)
P1683 (40) Throttle Valve Default Position Spring Performance Problem ON (see page 11-247)
P1684 (40) Throttle Valve Return Spring Performance Problem ON (see page 11-248)
P16BB (116) Alternator B Terminal Circuit Low Voltage OFF (see page 11-165)
P16BC (116) Alternator FR Terminal Circuit/IGP Circuit Low Voltage OFF (see page 11-166)
P2101 (40) Electronic Throttle Control System (ETCS) Malfunction ON (see page 11-249)
P2118 (40) Throttle Actuator Current Range/Performance Problem ON (see page 11-251)
P2122 (37) Accelerator Pedal Position (APP) Sensor A (Throttle Position (TP)
Sensor D) Circuit Low Voltage ON (see page 11-253)
P2123 (37) Accelerator Pedal Position (APP) Sensor A (Throttle Position (TP)
Sensor D) Circuit High Voltage ON (see page 11-256)
P2127 (37) Accelerator Pedal Position (APP) Sensor B (Throttle Position (TP)
Sensor E) Circuit Low Voltage ON (see page 11-257)
P2128 (37) Accelerator Pedal Position (APP) Sensor B (Throttle Position (TP)
Sensor E) Circuit High Voltage ON (see page 11-260)
P2135 (7) Throttle Position (TP) Sensor A/B Incorrect Voltage Correlation ON (see page 11-262)
P2138 (37) Accelerator Pedal Position (APP) Sensor A/B (Throttle Position (TP)
Sensor D/E) Incorrect Voltage Correlation ON (see page 11-264)
P2176 (40) Throttle Actuator Control System Idle Position Not Learned ON (see page 11-266)
P2183 (192) Engine Coolant Temperature (ECT) Sensor 2 Circuit Range/
Performance Problem ON (see page 11-168)
P2184 (192) Engine Coolant Temperature (ECT) Sensor 2 Circuit Low Voltage ON (see page 11-170)
P2185 (192) Engine Coolant Temperature (ECT) Sensor 2 Circuit High Voltage ON (see page 11-172)
P2195 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) Signal Stuck Lean ON (see page 11-174)
NOTE:  The above DTCs are indicated when the PGM-FI system is selected with the HDS.
 Some automatic transmission DTCs cause the MIL to come on. If the MIL is on and no DTCs are indicated in the PGM-FI system, select the A/T system, and check for automatic transmission DTCs.
: These DTCs are indicated by a blinking MIL when the SCS line is jumped with the HDS.
1: A/T
2: The D indicator and the MIL may come on at the same time (A/T).
3: M/T
4: K20Z2 engine
5: K20Z3 engine
9: ’09 model
(cont’d)
1
9
1, 2
3
4
5
5
3
1
08/08/21 14:12:36 61SNR030_110_0011
ProCarManuals.com
DYNOMITE -2009-

Ó
•••
•••
••• ´
••• µ Ó
Ó
Ó
Ó
•••
•••
•••
•••
••• Ó
•••
•••
•••
•••
•••
DTC
(MIL indication ) Two Drive Cycle
Detection Detection Item MIL Note
11-12Fuel and Emissions Systems
DTC Troubleshooting Index (cont’d)
P2227 (13)
Barometric Pressure (BARO) Sensor Circuit Range/Performance
Problem ON (see page 11-176)
P2228 (13) Barometric Pressure (BARO) Sensor Circuit Low Voltage ON (see page 11-177)
P2229 (13) Barometric Pressure (BARO) Sensor Circuit High Voltage ON (see page 11-177)
P2238 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) AFS Circuit Low Voltage ON (see page 11-178)
P2252 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) AFS Circuit Low Voltage ON (see page 11-179)
P2270 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit Signal Stuck Lean ON (see page 11-181)
P2271 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit Signal Stuck Rich ON (see page 11-181)
P2413 (12) Exhaust Gas Recirculation (EGR) System Malfunction ON (see page 11-363)
P2422 (117) Evaporative Emission (EVAP) Canister Vent Shut Valve Stuck Closed
Malfunction ON (see page 11-402)
P2610 (132) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Ignition Off Internal Timer Malfunction ON (see page 11-182)
P2646 (22) Rocker Arm Oil Pressure Switch Circuit Low Voltage ON (see page 11-284)
P2647 (22) Rocker Arm Oil Pressure Switch Circuit High Voltage ON (see page 11-287)
P2648 (21) Rocker Arm Oil Control Solenoid Circuit Low Voltage ON (see page 11-289)
P2649 (21) Rocker Arm Oil Control Solenoid Circuit High Voltage ON (see page 11-291)
P2A00 (61) Air Fuel Ratio (A/F) Sensor (Sensor 1) Circuit Range/Performance
Problem ON (see page 11-182)
U0028 (126) F-CAN Malfunction (BUS-OFF (Engine Control Module (ECM)/
Powertrain Control Module (PCM))) ON (see page 11-183)
U0122 (126) F-CAN Malfunction (Engine Control Module (ECM)/Powertrain
Control Module (PCM)-Vehicle Stability Assist (VSA) Modulator-
Control Unit) OFF (see page 11-184)
U0131 (126) F-CAN Malfunction (Engine Control Module (ECM)/Powertrain
Control Module (PCM)-Electrical Power Steering (EPS) Control Unit) OFF (see page 11-186)
U0155 (126) F-CAN Malfunction (Engine Control Module (ECM)/Powertrain
Control Module (PCM)-Gauge Control Module) ON (see page 11-188)
U0300 (131) PGM-FI System and A/T System Program Version Mismatch ON (see page 11-190)
NOTE:  The above DTCs are indicated when the PGM-FI system is selected with the HDS.
 Some automatic transmission DTCs cause the MIL to come on. If the MIL is on and no DTCs are indicated in the PGM-FI system, select the A/T system, and check for automatic transmission DTCs.
: These DTCs are indicated by a blinking MIL when the SCS line is jumped with the HDS.
1: A/T
4: K20Z2 engine
6: with VSA
4
6
1
08/08/21 14:12:36 61SNR030_110_0012
ProCarManuals.com
DYNOMITE -2009-

(#')
Symptom Diagnostic procedure Also check for
11-13
Symptom Troubleshooting Index
When the vehicle has one of these symptoms, check for a diagnostic trouble code (DTC) with the HDS. If there is no
DTC, do the diagnostic procedure for the symptom, in the sequence listed, until you find the cause.












Engine will not start
(MIL works OK, no DTCs set)
1.
2.
3.
4.Test the battery (see page 22-67).
Test the starter (see page 4-9).
Check the fuel pressure (see page 11-325).
Troubleshoot the fuel pump circuit (see page 11-
318).Low compression
No ignition spark
Intake air leaks
Locked up engine
Broken cam chain
Fuel contamination
Engine will not start
(MIL comes on and stays on,
no DTCs set) Troubleshoot the DLC circuit (see page 11-204).
MIL comes on and stays on,
or never comes on at all, no
DTCs set Troubleshoot the MIL circuit (see page 11-203).
Engine will not start
(MIL works OK, no DTCs set,
immobilizer indicator stays
on or flashes) Check the immobilizer system (see page 22-321).
Engine starts but stalls
immediately
(MIL works OK, no DTCs set,
immobilizer indicator stays
on or flashes) Check the immobilizer system (see page 22-323).
Engine is hard to start
(MIL works OK, no DTCs set) 1.
2.
3.Test the battery (see page 22-67).
Check the fuel pressure (see page 11-325).
Clean the throttle body (see page 11-
344).Low compression
Intake air leaks
Fuel contamination
Weak spark
Cold fast idle too low
(MIL works OK, no DTCs set) 1.
2.
3.DotheECM/PCMidlelearnprocedure(seepage
11-310).
Check the idle speed (see page 11-309).
Clean the throttle body (see page 11-
344).
Cold fast idle too high
(MIL works OK, no DTCs set) 1.
2.
3.DotheECM/PCMidlelearnprocedure(seepage
11-310).
Check the idle speed (see page 11-309).
Do the throttle position learning check (see page
11-343). Intake air leaks
Idle speed fluctuates
(MIL works OK, no DTCs set) 1.
2.
3.
4.DotheECM/PCMidlelearnprocedure(seepage
11-310).
Check the idle speed (see page 11-309).
Do the carbon accumulation check (see page 11-343).
Troubleshoot the A/C signal circuit (see page 11-306). Incorrect valve
timing or clearance
adjustment
Intake air leaks
After warming up, idle speed
is below specification without
load
(MIL works OK, no DTCs set) 1.
2.
Troubleshoot the alternator FR signal circuit
(see page 11-307).
Do the carbon accumulation check (see page 11-343). Incorrect valve
timing or clearance
adjustment
After warming up, idle speed
is above specification without
load
(MIL works OK, no DTCs set) 1.
2.
Troubleshoot the alternator FR signal circuit
(see page 11-307).
Inspect the APP sensor (see page 11-268). Intake air leaks
(cont’d)
08/08/21 14:12:36 61SNR030_110_0013
ProCarManuals.com
DYNOMITE -2009-

SymptomDiagnostic procedure Also check for
11-14Fuel and Emissions Systems
Symptom Troubleshooting Index (cont’d)










Low power
(MIL works OK, no DTCs set)
Check the fuel pressure (see page 11-325). Low compression
Incorrect camshaft
timing
Incorrect engine oil
level
Exhaust restriction
Engine stalls
(MIL works OK, no DTCs set) 1.
2.
3.
4.DotheECM/PCMidlelearnprocedure(seepage
11-310).
Check the fuel pressure (see page 11-325).
Check the idle speed (see page 11-309).
Troubleshoot the brake pedal position switch signal
circuit (see page 11-308). Intake air leaks
Faulty harness and
sensor
connections
Fuel contamination
Difficult to refuel
(MIL works OK, no DTCs set) 1.
2.
3.Check the fuel vent tube between the EVAP canister
and the fuel tank.
Check the fuel tank vapor recirculation tube between
thefuelpipeandthefueltank.
Replace the fuel tank (see page 11-339). Malfunctioning gas
station filling
nozzle.
Filler neck
restriction
Faulty fuel tank
vapor control valve
Fuel overflows during
refueling
(No DTCs set) Replace the fuel tank (see page 11-339). Malfunctioning gas
station filling nozzle.
HDS does not communicate
with the ECM/PCM or the
vehicle Troubleshoot the DLC circuit (see page 11-204).
Fuel cap warning message
stays on
(MIL works OK, no DTCs set)
(K20Z3 engine) Troubleshoot the fuel cap warning message system
(see page 11-405).
08/08/21 14:12:36 61SNR030_110_0014
ProCarManuals.com
DYNOMITE -2009-

(#')
Electronic Control Systems
Self-diagnosisOne Drive Cycle Detection Method
Two Drive Cycle Detection Method
Fail-safe Function
MIL Bulb Check and Readiness Code Condition
Self Shut Down (SSD) Mode
11-15
System Description
The functions of the fuel and emission control systems are managed by the engine control module (ECM) on vehicles
with manual transmissions or the powertrain control module (PCM) on vehicles with automatic transmissions.
The ECM/PCM detects a failure of a signal from a sensor or another control unit and stores a Temporary DTC or a DTC.
Depending on the failure, a DTC is stored in either the first or the second drive cycle (K20Z3 engine: DTC P0457, turns
on the malfunction indicator lamp (MIL) during the third drive cycle). When a DTC is stored, the ECM/PCM turns on the
malfunction indicator lamp (MIL) by a signal sent to the gauge via F-CAN.  When an abnormality occurs in the signal from a sensor or from another control unit, the ECM/PCM stores a DTC
and turns on the MIL immediately.
 When an abnormality occurs in the signal from a sensor or from another control unit in the first drive cycle, the
ECM/PCM stores a Temporary DTC. If the failure continues in the second drive cycle, the ECM/PCM stores a DTC and
turns on the MIL.
When an abnormality occurs in the signal from a sensor or another control unit, the ECM/PCM ignores the signal and
substitutes a pre-programmed value that allows the engine to continue running. This causes a DTC to be stored and
the MIL to come on.
When the ignition switch is turned to ON (II), the ECM/PCM turns on the MIL via the F-CAN circuit for about 15 to
20 seconds to check the bulb condition. If any readiness codes are not set to complete, the MIL flashes five times. If all
readiness codes are set to complete, the MIL goes off.
After the ignition switch is turned to LOCK (0), the ECM/PCM stays on (about 30 minutes). If the ECM/PCM connector is
disconnected during this time, the ECM/PCM may be damaged. To cancel this mode, disconnect the negative cable
from the battery or jump the SCS line with the HDS after the ignition switch is turned to LOCK (0).
(cont’d)
08/08/21 14:12:37 61SNR030_110_0015
ProCarManuals.com
DYNOMITE -2009-

ÃŽ
´
ECM/PCM Electrical Connections
11-16Fuel and Emissions Systems
System Description (cont’d)
IGNITION
SWITCH
IG1
ST B
IG2
IG1 HOT in ON (II)
and START (III) IGNITION COIL
RELAY
ELD PGM-FI MAIN
RELAY 2 (FUEL PUMP)P
FUEL PUMP
PGM-FI MAIN
RELAY 1
BATTERY A/C CONDENSER
FAN RELAYRADIATOR
FAN RELAY
A/C COMPRESSOR
CLUTCH RELAY
To
COOLING
FAN CONTROL
RELAY E
A8 IGPC36 IG1
A14 ACC
A5 FANH A23 ELD
A4 FANL GF
C
B
D
A
PG1 B36PG2 B1
MRLY A6
IMOFPR A15
SUBRLY A21
ETCSRLY A20 STARTER CUT
RELAY (ST CUT)
PGMETCS C2 PGM-FI
SUBRELAY
ETCS CONTROL
RELAY
I
IG1ETCS C1
ECM/PCM
CLUTCH
INTERLOCK
SWITCH
H
J*2
*1
T
*3
*1: A/T
*2: M/T
*3: K20Z3 engine
UNDER-HOOD
FUSE/RELAY BOX:
No. 1 MAIN FUSE (100 A)
No.19FIMAIN(15A)
No. 2 IG MAIN (50 A)
No. 23 BACK UP (10 A)
No. 12 STOP & HORN
(15 A) No. 18 IG COIL (15 A)
UNDER-DASH
FUSE/RELAY BOX: No. 3 ALTERNATOR
(10 A) No. 2 FUEL PUMP (15 A)
No. 36 IG2 HAC (A/C)
(10 A)
UNDER-HOOD
FUSE/RELAY BOX: No.15OILLVL(7.5A)
No. 11 FI SUB (15 A)
No. 21 DBW (THROTTLE
ACTUATOR CONTROL) (15 A)
08/08/21 14:12:37 61SNR030_110_0016
ProCarManuals.com
DYNOMITE -2009-

ÃŽ
´
µ
11-17
A
No. 1 INJECTOR
No. 2 INJECTOR
No. 3 INJECTOR
No. 4 INJECTOR
IAT SENSOR
MAP SENSOR
SG1 C14
MAP C11
VCC1 C13
ECT SENSOR 1
ECT1 B23 IAT B31
KNOCK SENSOR
KS C42
K
SG2 B33
C6 INJ2
C5 INJ1
C7 INJ3
C8 INJ4 VG B30
VG B32 F
EGRP B29
VCC2 B18 MAF SENSOR
L
M
EGR B2 EGR VALVE
POSITION
SENSOR
EGR VALVE
N O
*1
C32 CKP
C31 CMPB
BARO SENSOR
(Built into
the ECM/PCM)
CMP SENSOR B
CKP SENSOR A28 NEP
To EPS CONTROL UNIT *4
*1: A/T
*4: K20Z2 engine
(cont’d)
08/08/21 14:12:38 61SNR030_110_0017
ProCarManuals.com
DYNOMITE -2009-