Acura RL 2001 3.5 Owner's Manual

Armrest

The rear seat armrest is located at the center of the rear seat. Pivot itdown to use it. Trunk Pass-through Cover
The pass-through cover can be opened from either side; it folds
forward onto the center armrest. Open the cover by sliding the knob
downward and pushing or pulling on
the cover. To close the cover, swing
it up and push firmly on the top.
Make sure it latches properly. Make sure all items in the trunk and
those extending through the pass-
through are secured.
For security, this cover can be
locked and unlocked only with the master key. To lock the cover, insert
the key and turn it clockwise.
Never drive with this cover open and
the trunk lid open. See Carbon Monoxide Hazard on
page 49.

Instruments and Controls
KNOB
LID

Mirrors

Keep the inside and outside mirrors
clean and adjusted for best visibility.
Be sure to adjust the mirrors before
you start driving.
The inside mirror has an automaticanti-glare mechanism. When the
AUTO switch is pushed in, the indicator will light. When the mirrorsenses light from the headlights of
the car behind you, the mirror surface will automatically darken to
reduce the glare. Adjusting the Power Mirrors
Adjust the outside mirrors with the adjustment button on the driver's
door armrest:
1. Turn the ignition switch ON (II).
2. Move the selector switch to L (driver's side) or R (passenger's

side).

CONTINUED

Instruments and Controls

INDICATOR
SENSOR
AUTO SWITCH SELECTOR SWITCH

Mirrors

ADJUSTMENT BUTTON

3. Move the mirror right, left, up or
down by pushing the adjustment

button in that direction.
4. When you finish, move the
selector switch to the center (off)
position. This turns off the adjustment button so you can't
move a mirror out of position by accidentally bumping the button.
Outside mirror positions can be
stored in the driving position
memory system (see page 101).
HEATED MIRROR BUTTON

The outside mirrors are heated to re- move fog and frost. With the ignitionswitch ON (II), turn on the heaters
by pressing the button. The light in the button comes on as a reminder.
Press the button again to turn the
heaters off.
Instruments and Controls

Driving Position Memory System

Your Acura has a memory feature for the steering wheel, driver's seat, and outside mirror positions.
Two seat, steering wheel, and outside mirror positions for different
drivers or driving conditions can be
stored in separate memories. You
select a memorized position by
pushing the appropriate button.
Storing a Driving Position in Memory

Store a driving position as explained
in this section only when the car is
parked.
1. Turn the ignition switch ON (II). You cannot add a new drivingposition in the memory unless the
ignition switch is ON (II). You canrecall a memorized position with
the ignition switch in any position.
2. Adjust the seat to a comfortable position (see page 94). Adjust
the steering wheel to acomfortable position (see page
71).

Adjust the outside mirrors for best visibility (see page 99). 3. Press and release the MEMO
button on the control panel. You
will hear a beep. Immediately press and hold one of the memory
buttons (1 or 2) until you hear two beeps. The indicator light in thememory button will come on. The
current positions of the driver's
seat, steering wheel, and outside
mirrors are now stored.
CONTINUED
Instruments and Controls
MEMO BUTTON

Driving Position Memory System

Doing any of the following after
pressing the MEMO button will cancel the storing procedure. Not pressing a memory button
within 5 seconds. Readjusting the seat or steering
position. Readjusting the outside mirror
position.
Each memory button stores only one driving position. Storing a new
position erases the previous setting stored in that button's memory. If
you want to add a new position while retaining the current one, use the
other memory button.
All stored driving positions will be lost if your car's battery goes dead or
is disconnected.
Selecting a Memorized Position

You can select memorized positions as follows.
1. Make sure the parking brake is set and the shift lever is in Park.
2. Insert the key in the ignition switch. If you do not insert the key
in the ignition switch, the steering
wheel will not adjust to the memorized position until you do. 3. Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
The system will move the seat, steering wheel and outside mirrors
to the memorized positions. The indicator light in the selected
memory button will flash during
movement. When the adjustments
are complete, you will hear two
beeps and the indicator light will remain on.

Instruments and Controls
MEMORY BUTTONS

Driving Position Memory System, Seat Heaters

To stop the system's automatic ad- justment; Press any button on the control
panel: MEMO, 1 or 2.
Push any of the adjustment
switches for the seat or steering
wheel. Shift out of Park. Adjust the outside mirrors.
If you select a memorized position
without inserting the key in the ignition switch, only the seat andoutside mirrors will adjust. To get
the system to also adjust the steering
wheel, insert the key in the ignition switch. You will hear two beeps
when it is complete. If desired, you can use the adjust-
ment switches to change the posi-
tions of the seat, steering wheel or outside mirrors after they are in
their memorized position. To keep
this driving position for later use,
you must store it in the driving posi- tion memory. Seat Heaters
Both front seats are equipped withseat heaters. The ignition switch
must be ON (II) to use them. Push
the front of the switch, HI, to rapidly
heat up the seat. After the seat reaches a comfortable temperature,select LO by pushing the back of the
switch. This will keep the seat warm.

CONTINUED

Instruments and Controls
SEAT HEATERS

Seat Heaters, Ski Sleeve

The HI or LO indicator lights and remains lit until you turn it off by
pushing the opposite side of theswitch lightly. The indicator will turn

off.
In HI, the heater turns off when the

seat gets warm, and turns back on
after the seat's temperature drops. It
continues to cycle as long as you
leave it set on HI. The HI indicator
remains lit as a reminder that you
have the heater on.
In LO, the heater runs continuously.It does not cycle with temperature

changes.

Because of the sensors for the side
airbag system, there is no heater in
the passenger's seat-back. Follow these precautions whenever
you use the seat heaters: Use the HI setting only to heat the
seats quickly. Select the LO
setting when the seats feel warm.
The HI setting draws large amounts of current from the
battery. Do not use the seat heaters, even
on the LO setting, if the engine is
left idling for an extended period.
They can weaken the battery, causing hard starting.
Ski Sleeve

The ski sleeve allows you to carry skis or other long objects safely
without soiling or damaging the
interior of your car. It attaches to the
trunk pass-through.
KNOB
To use the ski sleeve: 1. Pull down the rear seat armrest. Open the trunk pass-through
cover by sliding the knob down-
ward and pulling on the cover.

Instruments and Controls
LID

Ski Sleeve

2. Open the trunk. Remove the ski sleeve from its storage bag.
3. Attach the ski sleeve to the trunk pass-through.
4. Load the skis into the ski sleeve from the trunk. Make sure the tipof the ski sleeve is resting on the
center console. 5. Use the strap on the ski sleeve to
secure it tightly to the rear seat
armrest. Follow these precautions when you
use the ski sleeve: Do not transport skis that are
longer or heavier than these limits: Maximum length: 84 in (215 cm)
Maximum weight: 55 Ibs (25 kg) After use, make sure the ski
sleeve is dry both inside and out
before folding it up for storage.
This will help to prevent mildew.

Instruments and Controls

Power Windows
Your car's windows are electrically- powered. Turn the ignition switch toON (II) to raise or lower any window.
Each door has a switch that controls
its window. To open the window,
push the switch down and hold it. Release the switch when you want
the window to stop. Close the
window by pulling back on the switch and holding it.
DRIVER'S WINDOW SWITCH
MAIN SWITCH

The driver's door armrest has a master power window control panel.
To open any of the passengers' win- dows, push down on the appropriate
switch and hold it down until the
window reaches the desired position.
To close the window, pull back on the window switch. Release theswitch when the window gets to the
position you want.

Instruments and Controls
Closing a power window on
someone's hands or fingers can
cause serious injury.
Make sure your passengers are
away from the windows before
closing them.

Power Windows, Moonroof

The master control panel also con- tains these extra features:
AUTO — To open the driver's window fully, push the windowswitch firmly down and release it.
The window automatically goes all the way down. To stop the window
from going all the way down, pull back on the window switch briefly.
To open the driver's window only partially, push the window switchdown lightly and hold it. The window
will stop as soon as you release the
switch.

The AUTO function only works to lower the driver's window. To raise
the window, you must pull back on
the window switch and hold it until the window reaches the desired

position.
The MAIN switch controls power to
the passengers'windows. With thisswitch off, the passengers'windows
cannot be raised or lowered. The
MAIN switch does not affect the driv-
er's window. Keep the MAIN switch
off when you have children in the car
so they do not injure themselves by
operating the windows unintentional-
ly. The lights inside the switches
come on when you turn the parking
lights or headlights on.
The power window system has a key- off delay function. The windows willstill operate for up to ten minutes
after you turn off the ignition.
Opening either front door cancels
the delay function. You must turn
the ignition switch ON (II) again
before you can raise or lower the
windows. Moonroof
There are two switches on the ceiling near the front ceiling light.
The ignition switch must be ON (II).
To open the moonroof, pull the OPEN/CLOSE switch backward and
hold it until the moonroof reaches
the desired position.

CONTINUED

Instruments and Controls
OPEN/CLOSE
SWITCH