Acura TSX 2013 Navigation Manual

50

Routing & Guidance
Unverified Area Routing
System Setup
Unverified Area RoutingHINFO/PHONE button
 Setup
 Other
 Routing & Guidance
 Unverified
Area RoutingReceive turn-by-turn map and voic
e guidance in unverified areas.
Rotate
i
to select
ON
or
OFF
.
1Unverified Area RoutingUnverified roads are found in rural areas, and typically include
residential streets away from the
center of a town. They may not be accurate, and can contain errors in
location, naming, and
address range. Unverified roads are s
hown only when viewing
the map in the 1/20, 1/8 and 1/4 mile map scales.
Vector line (dotted)
Blue-pink route line
Differences OFF (factory default)
ON
ON or OFF?
The driver wishes to manually navigate using the navigation map and choose the streets that lead to the destination.
The driver chooses to let the navigation system suggest possible routing, knowing that the guidance may not be accurate.
Route calculation
Route is usually longer, using verified roads whenever possible.
Route is shorter, but uses unverified (purple) streets that may not be accurate.
Route line
A blue dotted vector line is displayed on the map that continually points to your destination.
A blue-pink dashed route line highlights suggested unverified streets on the map while traveling to your destination.
Cautionary messages
Cautionary pop-up screens and voice announcements remind you to obey all traffic restrictions.
Cautionary pop-up screens and voice announcements remind you to exercise additional caution and obey all traffic restrictions.
QRG
Press
u
.

51

Routing & Guidance
Unverified Area Routing
Guidance (map/voice)
There is no turn-by-turn map or voice guidance.
Voice guidance commands end with the phrase “if possible” to remind you to verify all traffic restrictions.
Directions list
A direction list is typically not available. However, depending on your route, directions are provided to help you reach the first available verified road.
A direction list is provided showing street names and turn symbols in pink.
Differences OFF (factory default)
ON
QRG
System Setup

52

Routing & Guidance
Traffic Rerouting
System Setup
Traffic ReroutingHINFO/PHONE button
 Setup
 Other
 Routing & Guidance
 Traffic
ReroutingA faster route can be calculated based
on continuously updated traffic information.
2Traffic Rerouting™
P. 119
Rotate
i
to select an option.
The following options are available: •ON
: The system reroutes automati
cally based on
traffic information.
•OFF
(factory default): Disables the feature.
1Traffic ReroutingTraffic Rerouting
requires an Ac
uraLink Real-
Time Traffic™ subscription. 2AcuraLink Real-Time Traffic™
P. 15
2Subscribing to XM® Radio
P. 144
Automatic traffic rerout
ing may not provide a
detour route dependi
ng on circumstances.
QRG
Press
u
.

53

Routing & Guidance
Edit Avoid Area
Edit Avoid AreaHINFO/PHONE button
 Setup
 Other
 Routing & Guidance
 Edit Avoid
AreaSpecify up to five areas to avoid (e.g., road
construction, closures), if possible, when
the system calculates routes to your destination.
1.Rotate
i
to select
New Area
or
an existing area to edit. Press
u
.
2.Rotate
i
to select
Edit Name
to
label the area to avoid. Press
u
.
3.Enter a name or title. Move
r to
select
OK
.
4.Rotate
i
to select
Edit Area
to
define the area to avoid. Press
u
.
The following options are available: •View Area Map
: Displays the selected avoid area on the map.
•Delete
: Deletes the selected avoid area.
1Edit Avoid AreaThe avoid areas are shared with Driver 1 and Driver 2. For example, if Driver 1 specifies some avoid areas, Driver 2 can also use them for setting a route. The maximum size of an “avoid area” is 1/2 square mile. If your selected area contains a freeway, you are asked “Do you want to avoid freeways?” Answering “No” allows you to use a route through an avoid area on
a freeway without any
pop-up messages. You can select areas to
avoid, however you
cannot select roads or areas that you want the system to use for routing. You can enter up to 25 ch
aracters for the name.
Continued
QRG
System Setup

54

Routing & Guidance
Edit Avoid Area
System Setup
5.Rotate
i
to select a method for
specifying the area. Press
u
.
The following options are available: •Address
: Specify the general area by entering an address.
2Address
P. 70
•Map Input
: Specify the general area by map input.
2Map Input
P. 88
6.Scroll the map to position the cursor over your desired start point, adjusting the map scale as necessary. Press
u
to mark the
start point.
To redo the area selection, press the CANCEL button.
7.Scroll the map to “draw” the area. Press
u
to mark the end point.
8.Press
u
to select
OK
.

The area you specify is displayed in the list of areas to avoid.
Cursor
Avoid area
QRG

55

Routing & Guidance
Edit Waypoint Search Area
Edit Waypoint Search AreaHINFO/PHONE button
 Setup
 Other
 Routing & Guidance
 Edit
Waypoint Search AreaSelect the distance from your highlighted ro
ute line (on either side of your route)
that the system will search for a waypoint. 2Adding Waypoints
P. 123
You can specify a different search distance for freeways and surface streets.
1.Rotate
i
to select an item.
2.Rotate
i
to select a search
distance. Press
u
.
The following items are available: •On Freeways
: 1, 2, 5, or 10 miles can be
set. Factory default is 2 miles.
•On Surface Street
: 1/2, 1, 2, or 5 miles can be
set. Factory default is 1/2 mile.
1Edit Waypoint Search AreaThe search distance does
not affect the search
range used for the Find Nearest voice commands (e.g., say
d
“Find nearest gas station”
).
QRG
System Setup
Press
u
.

56

Routing & Guidance
Street Name Guidance
System Setup
Street Name GuidanceHINFO/PHONE button
 Setup
 Other
 Routing & Guidance
 Street
Name GuidanceThe navigation system includes the street
names during voice guidance (e.g., “Turn
right on Main Street”).
Rotate
i
to select an option.
The following options are available: •ON
: Voice guidance includes the street names.
•OFF
(factory default): Disables the feature.
1Street Name GuidanceStreet Name Guidance
is grayed out when the
system language is not set to
English
.
QRG
Press
u
.

57

Routing & Guidance
Guidance Screen Interruption
Guidance Screen InterruptionHINFO/PHONE button
 Setup
 Other
 Routing & Guidance
 Guidance
Screen InterruptionThe navigation system temporarily interrupt
s the audio screen di
splay to view the
guidance screen as you approach a guidance point.
Rotate
i
to select an option.
The following options are available: •ON
: The guidance screen interrupts the audio screen.
•OFF
(factory default): Disables the feature.
QRG
System Setup
Press
u
.

58System Setup
Clock AdjustmentHINFO/PHONE button
 Setup
 Other
 Clock Adjustment
Set the automatic adjustment of the
system clock for daylight saving and
international time zones.
Rotate
i
to select an item. Press
u
.
The following item
s are available:
•Auto Daylight
: The navigation system automati
cally adjusts the clock (“spring
ahead” or “fall back” by one hour) when a daylight saving time change occurs. ON
(factory default): Adjust
s the clock automatically.
OFF
: Disables the feature.
•Auto Time Zone
: The navigation system automati
cally adjusts the clock when
driving through different time zones.ON
(factory default): Adjust
s the clock automatically.
OFF
: Disables the feature.
•ADJUST TIME
: Adjust the current time manually.
2Adjust Time
P. 59
•Reset
: Reset the clock settings to the factory default.
2Resetting the Clock Settings
P. 59
1Clock AdjustmentYou can check the time and date from any screen using voice commands. 2Global Commands
P. 236
Auto Daylight This function is not activated in areas that have not adopted daylight savi
ng time, even if you
have set
Auto Daylight
to
ON
.
Auto Time ZoneIf you live and work in
two different time zones,
you may want to turn
Auto Time Zone
to
OFF
.
When driving near a time zone boundary, the displayed time zone ma
y fluctuate between the
two zone times.
QRG

59

Clock Adjustment
Adjust Time
System Setup
Adjust TimeHINFO/PHONE button
 Setup
 Other
 Clock Adjustment
 Adjust Time
Adjust the current time
(hours and minutes).
1.Move
w
or
y
to select
HOUR
or
MINUTE
.
2.Rotate
i
to adjust the value.
3.Move
r to select
OK
.
Resetting the Clock SettingsHINFO/PHONE button
 Setup
 Other
 Clock Adjustment
 Reset
Reset the
Auto Daylight
and
Auto Time Zone
settings to the factory defaults.
QRG