ACURA CSX 2006 Service Repair Manual


(#'


 )
20-27
Rear Door Weatherstrip Replacement
Fastener Locations:Bolt,1
A :Clip,13
B
B A B
C
D F
E C
E
E
E
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft) : Clip, 2
C
:Clip,1
D (White)
(Black) (Left: Yellow
Right: Green)
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
 Remove the clips with a clip remover.
1. At the B-pillar, remove the door checker mounting
bolt (A).
2. Detach the clips (B, C, D), then remove the door weatherstrip (E). 3. Install the weatherstrip in the reverse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Make sure the weatherstrip is installed in the holder (F) securely.
 Apply medium strength liquid thread lock to the door checker mounting bolt before installation.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:10 61SNR030_200_0029
ProCarManuals.com
DYNOMITE -2009-




(#'
")

Front
Rear
20-28Doors
Front and Rear Door Glass Adjustment
B
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
C A
B
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
C A
A
B
NOTE: Check the weatherstrip and glass run channel for
damage or deterioration, and replace them if necessary. 1. Place the vehicle on a firm, level surface.
2. Remove these items:  Door panel:– Front door (see page 20-7)
– Rear door (see page 20-17)
 Plastic cover: – Front door (see step 4 on page 20-9)
– Rear door (see step 4 on page 20-19)
3. Carefully move the glass (A) until you can see the glass mounting bolts (B), then loosen them.
4. Push the glass against the channel (C), then tightenthe glass mounting bolts.
5. Check that the glass moves smoothly.
6. Raise the glass fully, and check for gaps. Also make sure that the glass (A) contacts the glass run
channel (B) evenly.
08/08/21 14:59:11 61SNR030_200_0030
ProCarManuals.com
DYNOMITE -2009-



(#'

") Front door
20-2920-29
Front and Rear Door Position
Adjustment
12 mm (0.47 in.)
0.5m(19in.)
300 mm (12 in.) B
C
A
D
8x1.25mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
F
8x1.25mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
A
B C
7. Attach the plastic cover making sure it its sealed
around its outside perimeter to seal out water.
8. Reinstall the door panel:  Front door (see page 20-9)
 Rear door (see page 20-19)
9. Check for water leaks. Run water over the roof and on the sealing area as shown, and note these items:
 Use a 12 mm (0.47 in.) diameter hose (A).
 Adjust the rate of water flow as shown (B).
 Do not use a nozzle.
 Hold the hose about 300 mm (12 in.) away from the door (C). NOTE: Check for a flush fit with the body, then check for
equal gaps between the front, rear, and bottom door
edges and the body. Check that the door and the body
edges are parallel. If necessary, replace the mounting
bolts before adjusting the door position.
1. Place the vehicle on a firm, level surface when adjusting the doors.
2. Adjust at the hinges (A):  Pad a floor jack (B) with shop towels (C), then usethe jack to support the door to prevent damage to
the door while adjusting it.
 On the front door: Remove the front inner fender (see page 20-171). Loosen the hinge m ounting
bolts (D) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
 On the rear door: Loosen the hinge mounting bolts (E) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
(cont’d)
08/08/21 15:00:01 61SNR030_200_0031
ProCarManuals.com
DYNOMITE -2009-



(#'

") Front door
20-2920-29
Front and Rear Door Position
Adjustment
12 mm (0.47 in.)
0.5m(19in.)
300 mm (12 in.) B
C
A
D
8x1.25mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
F
8x1.25mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
A
B C
7. Attach the plastic cover making sure it its sealed
around its outside perimeter to seal out water.
8. Reinstall the door panel:  Front door (see page 20-9)
 Rear door (see page 20-19)
9. Check for water leaks. Run water over the roof and on the sealing area as shown, and note these items:
 Use a 12 mm (0.47 in.) diameter hose (A).
 Adjust the rate of water flow as shown (B).
 Do not use a nozzle.
 Hold the hose about 300 mm (12 in.) away from the door (C). NOTE: Check for a flush fit with the body, then check for
equal gaps between the front, rear, and bottom door
edges and the body. Check that the door and the body
edges are parallel. If necessary, replace the mounting
bolts before adjusting the door position.
1. Place the vehicle on a firm, level surface when adjusting the doors.
2. Adjust at the hinges (A):  Pad a floor jack (B) with shop towels (C), then usethe jack to support the door to prevent damage to
the door while adjusting it.
 On the front door: Remove the front inner fender (see page 20-171). Loosen the hinge m ounting
bolts (D) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
 On the rear door: Loosen the hinge mounting bolts (E) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
(cont’d)
08/08/21 15:00:01 61SNR030_200_0031
ProCarManuals.com
DYNOMITE -2009-


Rear door
20-30 Doors
Front and Rear Door Position Adjustment (cont’d)
F
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft)
E
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft) A
A B
C
E
8x1.25mm
29N·m(3.0kgf·m,22lbf·ft) F
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft)
A
A
A
3. If necessary, replace the door mounting bolts with
the adjusting bolts (P/N 90102-SFA-305) made
specifically for door adjustment, then adjust at the
door: Loosen the door mounting bolts (F) slightly,
and move the door up or down as necessary to
equalize the gaps, and move it in or out until it’s
flush with the body. 4. Check that the door and body edges are parallel. If
necessary, adjust the door cushions (A) to make the
rear of the doors flush with the body.
5. Apply touch-up paint to the hinge mounting bolts, and around the hinges.
6. Check for water leaks (see step 9 on page 20-29).
08/08/21 15:00:02 61SNR030_200_0032
ProCarManuals.com
DYNOMITE -2009-


(#'



")
20-31
Front and Rear Door Striker Adjustment
B
8x1.25mm
18 N·m (1.8 kgf·m, 13 lbf·ft) A
C
Make sure the door latches securely without slamming
it. If necessary, adjust the striker (A): The striker nuts
are fixed, but the striker can be adjusted slightly up or
down, and in or out.1. Loosen the screws (B).
2. Wrap the striker with a shop towel, then adjust the striker by tapping it with a plastic hammer (C). Do
not tap the striker too hard.
3. Lightly tighten the screws.
4. Hold the outer handle out, and push the door against the body to be sure the striker allows a
flush fit. If the door latches properly, tighten the
screws to the specified torque, and recheck.
08/08/21 15:00:02 61SNR030_200_0033
ProCarManuals.com
DYNOMITE -2009-

Î
Î(#')
20-32Mirrors
Component Location Index
MIRROR HOLDER
POWER MIRROR
REARVIEW MIRROR
Replacement, page 20-34
Replacement,
page 20-33
Replacement, page 20-35
08/08/21 15:00:03 61SNR030_200_0034
ProCarManuals.com
DYNOMITE -2009-



(#'
 )

20-33
Power Mirror Replacement
B
A
Fastener Locations :Nut,3
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)A A
B
C
1. Raise the door glass fully.
2. Remove these items:  Door panel (see page 20-7)
 Plastic cover, as needed (see step 4 on page 20-9)
3. Disconnect the connector (A), and detach the harness clip (B).
4. Remove the maintenance cap (A), and remove the nuts. 5. While holding the mirror (A), detach the clip (B),
then remove the mirror, and pull the harness (C)
out through the hole in the door. Take care not to
scratch the door.
6. Install the mirror in the reverse order of removal, and make sure the connector is plugged in properly.
08/08/21 15:00:04 61SNR030_200_0035
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
20-34 Mirrors
Mirror Holder Replacement
A
B C
A
B
C
D E
C
E
F A
B
C B
A B
C
A
C
CB A
A
B
C
NO GOOD
OK
NOTE: Put on gloves to protect your hands.
1. Carefully push on the top edge of the mirror holder (A) by hand.
2. Put a shop towel in the opening between the lower edge of the mirror holder and the mirror housing
(B) to prevent scratches, and detach the bottom
clips (C) with a flat-tip screwdriver wrapped with
protective tape.
3. Carefully pull out the bottom edge of the mirror holder (A) to separate the adhesive (B), and then
release the side clips (C).
4. Separate the mirror holder from the actuator (D) by releasing the hooks (E). Disconnect the mirror
defogger connectors (F) from the heater pad
terminals. 5. Before reinstalling the mirror holder to the inner
holder (A) on the actuator, check the actuator rods
(B) and the actuator boots (C). Make sure the
actuator rods are securely mounted in the holes,
and that the boots properly cover each rod.
6. Reconnect the mirror defogger connectors.
7. Reattach the hooks of the mirror holder to the actuator, then position the mirror holder on the
actuator. Carefully push on the clip portions of the
mirror holder until the mirror holder locks into
place.
8. Check the actuator operation.
08/08/21 15:00:05 61SNR030_200_0036
ProCarManuals.com
DYNOMITE -2009-


(#'
 )
20-35
Rearview Mirror Replacement
A
A B
C
1. Turn the rearview mirror base (A) 90 °.
2. Slide the rearview mirror (A) down toward thebottom of the windshield to detach it from the
spring (B) in the mount (C).
3. Install the rearview mirror in the reverse order of removal.
08/08/21 15:00:05 61SNR030_200_0037
ProCarManuals.com
DYNOMITE -2009-