CADILLAC ESCALADE 2010 3.G Owners Manual

1. Put the tire (H) on the ground at the rear of thevehicle with the valve stem pointed down and tothe rear.
2. Tilt the tire toward the vehicle. Separate the tire/wheel retainer (G) from the guide pin. Pull the pinthrough the center of the wheel. Tilt the retainerdown and through the center wheel opening.
3. Assemble the two jack handle extensions (D) andwheel wrench (E) as shown.
7-95

4. Insert the open end ofthe extension (J)through the hole in therear bumper (I) (hoistshaft access hole).
5. Raise the tire part way upward. Make sure theretainer is fully seated across the underside of thewheel and centered in the wheel opening.
6. Raise the tire fully against the underside of thevehicle by turning the wheel wrench clockwise untilyou hear two clicks or feel it skip twice. You cannotovertighten the cable.
7. Make sure the tire is stored securely. Push,pull (A), and then try to turn (B) the tire. If the tiremoves, use the wheel wrench to tighten the cable.
8. Reinstall the spare tire lock.
9. Reinstall the hoist shaft access cover.
10. Reinstall the hitch cover.
7-96

To store the tools:
A. Wheel Blocks
B. Tool Bag withJack Tools
C. Retaining Bracket
D. Wing Nut RetainingTool Bag
E. Jack
F. Wing Nut RetainingWheel Blocks
G. Jack Knob
1. Return the tools (wheel wrench, jack handle, andjack handle extensions) to the tool bag (B).
2. Assemble wheel blocks (A) and jack (E) togetherwith the wing nut (F).
3. Position the jack (E) and wheel blocks (A) in thedriver's side trim panel over the wheelhouse.
4. Turn the jack knob (G) clockwise until the jack issecured tight in the mounting bracket. Be sure toposition the holes in the base of the jack onto thepin in the mounting bracket.
5. Use the retaining bracket (C) to fasten the toolbag (B) on the stud and turn the wing nut (D)clockwise to secure.
Regular Wheelbase shown, ExtendedWheelbase similar.
6. Return the storage tray to its original storedposition.
7-97

Spare Tire
Your vehicle, when new, had a fully-inflated spare tire.A spare tire may lose air over time, so check its inflationpressure regularly. SeeInflation - Tire Pressureonpage 7!65andLoading the Vehicleon page 6!32forinformation regarding proper tire inflation and loadingyour vehicle. For instruction on how to remove, install orstore a spare tire, seeRemoving the Flat Tire andInstalling the Spare Tireon page 7!86andStoring aFlat or Spare Tire and Tools on page 7!94.
After installing the spare tire on your vehicle, you shouldstop as soon as possible and make sure the spare iscorrectly inflated. The spare tire is made to perform wellat speeds up to 70 mph (112 km/h) at the recommendedinflation pressure, so you can finish your trip.
Have the damaged or flat road tire repaired or replacedas soon as you can and installed back onto yourvehicle. This way, a spare tire will be available in caseyou need it again. Do not mix tires and wheels ofdifferent sizes, because they will not fit. Keep yourspare tire and its wheel together.
Appearance Care
Interior Cleaning
The vehicle's interior will continue to look its best if it iscleaned often. Although not always visible, dust and dirtcan accumulate on the upholstery. Dirt can damagecarpet, fabric, leather, and plastic surfaces. Regularvacuuming is recommended to remove particles fromthe upholstery. It is important to keep the upholsteryfrom becoming and remaining heavily soiled. Soilsshould be removed as quickly as possible. Thevehicle's interior may experience extremes of heat thatcould cause stains to set rapidly.
Lighter colored interiors may require more frequentcleaning. Use care because newspapers and garmentsthat transfer color to home furnishings may also transfercolor to the vehicle's interior.
When cleaning the vehicle's interior, only use cleanersspecifically designed for the surfaces being cleaned.Permanent damage may result from using cleaners onsurfaces for which they were not intended. Use glasscleaner only on glass. Remove any accidentalover-spray from other surfaces immediately. To preventover-spray, apply cleaner directly to the cleaning cloth.
7-98

Notice:Using abrasive cleaners when cleaningglass surfaces on the vehicle, could scratch theglass and/or cause damage to the rear windowdefogger. When cleaning the glass on the vehicle,use only a soft cloth and glass cleaner.
Many cleaners contain solvents that may becomeconcentrated in the vehicle's breathing space. Beforeusing cleaners, read and adhere to all safetyinstructions on the label. While cleaning the vehicle'sinterior, maintain adequate ventilation by opening thevehicle's doors and windows.
Dust may be removed from small buttons and knobsusing a small brush with soft bristles.
Products that remove odors from the vehicle'supholstery and clean the vehicle's glass can beobtained from your dealer/retailer.
Do not clean the vehicle using:
.A knife or any other sharp object to remove a soilfrom any interior surface.
.A stiff brush. It can cause damage to the vehicle'sinterior surfaces.
.Heavy pressure or aggressive rubbing with acleaning cloth. Use of heavy pressure can damagethe interior and does not improve the effectivenessof soil removal.
.Laundry detergents or dishwashing soaps withdegreasers can leave residue that streaks andattracts dirt. For liquid cleaners, about 20 drops pergallon (3.78 L) of water is a good guide. Use onlymild, neutral-pH soaps.
.Too much cleaner that saturates the upholstery.
.Organic solvents such as naptha, alcohol, etc. thatcan damage the vehicle's interior.
Fabric/Carpet
Use a vacuum cleaner with a soft brush attachmentfrequently to remove dust and loose dirt. A canistervacuum with a beater bar in the nozzle may only beused on floor carpet and carpeted floor mats. For anysoil, always try to remove it first with plain water or clubsoda. Before cleaning, gently remove as much of thesoil as possible using one of the following techniques:
.For liquids: gently blot the remaining soil with apaper towel. Allow the soil to absorb into the papertowel until no more can be removed.
.For solid dry soils: remove as much as possibleand then vacuum.
7-99

To clean:
1. Saturate a lint-free, clean white cloth with water orclub soda.
2. Wring the cloth to remove excess moisture.
3. Start on the outside edge of the soil and gently rubtoward the center. Continue cleaning, using a cleanarea of the cloth each time it becomes soiled.
4. Continue to gently rub the soiled area until thecleaning cloth remains clean.
5. If the soil is not completely removed, use a mildsoap solution and repeat the cleaning process thatwas used with plain water.
If any of the soil remains, a commercial fabric cleaner orspot lifter may be necessary. When a commercialupholstery cleaner or spot lifter is to be used, test asmall hidden area for colorfastness first. If the locallycleaned area gives any impression that a ring formationmay result, clean the entire surface.
After the cleaning process has been completed, a papertowel can be used to blot excess moisture from thefabric or carpet.
Leather
A soft cloth dampened with water can be used toremove dust. If a more thorough cleaning is necessary,a soft cloth dampened with a mild soap solution can beused. Allow the leather to dry naturally. Do not use heatto dry. Never use steam to clean leather. Never usespot lifters or spot removers on leather. Manycommercial leather cleaners and coatings that are soldto preserve and protect leather may permanentlychange the appearance and feel of the leather and arenot recommended. Do not use silicone or wax-basedproducts, or those containing organic solvents to cleanthe vehicle's interior because they can alter theappearance by increasing the gloss in a non-uniformmanner. Never use shoe polish on leather.
TEHAMA™Leather
The leather surface on the seat was not designed to beaggressively cleaned using any commercial product.Use a well wrung cloth dampened with water to removedust. Do not use a wet cloth or saturate the leathersurface with water. Allow the leather to dry naturally. If asoil occurs that cannot be completely removed, allow itto become part of the natural markings of the leather.The leather in the vehicle was designed to have anatural appearance and develop a more vintageappearance with use.
7-100

Do not use heat to dry. Never use steam to cleanleather. Never use spot lifters or spot removers onleather. It is very important to not use any commercialleather cleaners or coatings that are sold to preserveand protect leather. Not only are those products notnecessary, they will permanently and adversely changethe appearance and feel of the leather. Never usesilicone or wax-based products, or those containingorganic solvents to clean the vehicle's interior. Neveruse shoe polish on leather.
Instrument Panel, Vinyl, and Other
Plastic Surfaces
A soft cloth dampened with water may be used toremove dust. If a more thorough cleaning is necessary,a clean soft cloth dampened with a mild soap solutioncan be used to gently remove dust and dirt. Never usespot lifters or removers on plastic surfaces. Manycommercial cleaners and coatings that are sold topreserve and protect soft plastic surfaces maypermanently change the appearance and feel of theinterior and are not recommended. Do not use siliconeor wax-based products, or those containing organicsolvents to clean the vehicle's interior because they canalter the appearance by increasing the gloss in anon-uniform manner.
Some commercial products may increase gloss on theinstrument panel. The increase in gloss may causeannoying reflections in the windshield and even make itdifficult to see through the windshield under certainconditions.
Wood Panels
Use a clean cloth moistened in warm, soapy water (usemild dish washing soap). Dry the wood immediately witha clean cloth.
Speaker Covers
Vacuum around a speaker cover gently, so that thespeaker will not be damaged. Clean spots with justwater and mild soap.
7-101

Care of Safety Belts
Keep belts clean and dry.
{WARNING:
Do not bleach or dye safety belts. It may severely
weaken them. In a crash, they might not be able
to provide adequate protection. Clean safety belts
only with mild soap and lukewarm water.
Weatherstrips
Silicone grease on weatherstrips will make them lastlonger, seal better, and not stick or squeak. Applysilicone grease with a clean cloth. During very cold,damp weather frequent application may be required.SeeRecommended Fluids and Lubricantsonpage 8!10.
Washing Your Vehicle
The best way to preserve the vehicle's finish is to keepit clean by washing it often.
Notice:Certain cleaners contain chemicals that candamage the emblems or nameplates on the vehicle.Check the cleaning product label. If it states that itshould not be used on plastic parts, do not use it onthe vehicle or damage may occur and it would notbe covered by the warranty.
Do not wash the vehicle in direct sunlight. Use a carwashing soap. Do not use cleaning agents that arepetroleum based or that contain acid or abrasives, asthey can damage the paint, metal or plastic on thevehicle. Approved cleaning products can be obtainedfrom your dealer/retailer. Follow all manufacturers'directions regarding correct product usage, necessarysafety precautions and appropriate disposal of anyvehicle care product.
Rinse the vehicle well, before washing and after toremove all cleaning agents completely. If they areallowed to dry on the surface, they could stain.
Dry the finish with a soft, clean chamois or an all-cottontowel to avoid surface scratches and water spotting.
7-102

High pressure car washes may cause water to enter thevehicle. Avoid using high pressure washes closer than12 inches (30 cm) to the surface of the vehicle. Use ofpower washers exceeding 1,200 psi (8 274 kPa) canresult in damage or removal of paint and decals.
Cleaning Exterior Lamps/Lenses
Use only lukewarm or cold water, a soft cloth and a carwashing soap to clean exterior lamps and lenses.Follow instructions underWashing Your Vehicleonpage 7!102.
Finish Care
Occasional waxing or mild polishing of the vehicle byhand may be necessary to remove residue from thepaint finish. Approved cleaning products can beobtained from your dealer/retailer.
If the vehicle has a basecoat/clearcoat paint finish, theclearcoat gives more depth and gloss to the coloredbasecoat. Always use waxes and polishes that arenon-abrasive and made for a basecoat/clearcoat paintfinish.
Notice:Machine compounding or aggressivepolishing on a basecoat/clearcoat paint finish maydamage it. Use only non-abrasive waxes andpolishes that are made for a basecoat/clearcoatpaint finish on the vehicle.
Foreign materials such as calcium chloride and othersalts, ice melting agents, road oil and tar, tree sap, birddroppings, chemicals from industrial chimneys, etc., candamage the vehicle's finish if they remain on paintedsurfaces. Wash the vehicle as soon as possible.If necessary, use non-abrasive cleaners that aremarked safe for painted surfaces to remove foreignmatter.
Exterior painted surfaces are subject to aging, weatherand chemical fallout that can take their toll over a periodof years. To help keep the paint finish looking new, keepthe vehicle garaged or covered whenever possible.
Protecting Exterior Bright Metal Parts
Bright metal parts should be cleaned regularly to keeptheir luster. Washing with water is all that is usuallyneeded. However, chrome polish may be used onchrome or stainless steel trim, if necessary.
Use special care with aluminum trim. To avoiddamaging protective trim, never use auto or chromepolish, steam or caustic soap to clean aluminum.A coating of wax, rubbed to high polish, isrecommended for all bright metal parts.
7-103

Windshield, Backglass, and Wiper
Blades
Clean the outside of the windshield and backglass withglass cleaner.
Clean the rubber blades using a lint free cloth or papertowel soaked with windshield washer fluid or a milddetergent. Wash the windshield thoroughly when youclean the blades. Bugs, road grime, sap and a buildupof vehicle wash/wax treatments may cause wiperstreaking. Replace the wiper blades if they are worn ordamaged.
Wipers can be damaged by:
.Extreme dusty conditions
.Sand and salt
.Heat and sun
.Snow and ice, without proper removal
Aluminum or Chrome-Plated Wheels
and Trim
The vehicle may have either aluminum orchrome-plated wheels.
Keep the wheels clean using a soft clean cloth with mildsoap and water. Rinse with clean water. After rinsingthoroughly, dry with a soft clean towel. A wax may thenbe applied.
Notice:Chrome wheels and other chrome trim maybe damaged if the vehicle is not washed afterdriving on roads that have been sprayed withmagnesium, calcium or sodium chloride. Thesechlorides are used on roads for conditions such asice and dust. Always wash the vehicle's chromewith soap and water after exposure.
Notice:Using strong soaps, chemicals, abrasivepolishes, cleaners, brushes, or cleaners that containacid on aluminum or chrome-plated wheels, coulddamage the surface of the wheel(s). The repairswould not be covered by the vehicle warranty. Useonly approved cleaners on aluminum orchrome-plated wheels.
7-104