CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

ENGINE-ELECTRICAL
6Y-16

POINT
OPENINGJL

Fig. 17c-6.2"
Brush
Holder
Assembly

5. Rearrange leads as shown in Figure 18c with right-

hand brush lead connected under the right hand hex-

head stud.

6. Remove pin and attach terminal cover with two

screws, making sure leads are not caught under-

neath the cover.

DOUBLE CONTACT REGULATOR

While most regular adjustments are made on the vehi-

cle as outlined under "Maintenance and Adjustments",

the regulator may be removed for field relay point and

air gap adjustment. However, voltage regulating contacts

should never be cleaned as they are made of special

material that may be destroyed by cleaning with any

abrasive material.

NOTE:
A sooty or discolored condition of the

contacts is normal after a relatively short

period of operation.
Fig. 19c—Checking Field Relay Point Opening

REMOVAL AND INSTALLATION

To remove the regulator assembly, disconnect the bat-

tery ground cable and the wiring harness connector at the

regulator, then remove the screws securing the regulator

to the vehicle.

Electrical settings must be checked and adjusted after

making mechanical adjustments. Before installing regu-

lator cover, make sure the rubber gasket is in place on

the regulator base.

MECHANICAL ADJUSTMENTS

NOTE:
Only an approximate voltage regulator

air gap setting should be made by the "feeler

gauge" method.

BRUSH

LEAD

BRUSH

LEAD
RELAY
^B-/lliLlK
CONDENSER

LEAD
GROUND
LEAD

STUD
AIR GAP

(Check
With
Points

Just
Touching)

Fig.
18c—Lead
Arrangement
after
Assembly
Fig. 20c—Checking Field Relay Air Gap

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-17

Field Relay Adjustment touching (fig. 20c). The air gap normally need not be

adjusted. If the point opening and closing voltages

1.
Point Opening: The point opening is checked as il- are within specifications, the relay will operate

lustrated in Figure 19c. If adjustment is necessary, satisfactorily even though the air gap may not be

carefully bend the armature stop. exactly according to specifications. If adjustment is

2.
Air Gap: Check the air gap with the points just necessary, bend the flat contact spring.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-18

IGNITION SYSTEMS

INDEX

Page

General Description . 6Y-18

Maintenance and Adjustments 6Y-19

Breaker Point System 6Y-19

Breakerless System . . 6Y-X9

Ignition Coil Check 6Y-19

Spark Plugs 6Y-19

Service Operations , 6Y-19

Distributor Contact Points . 6Y-19

Cleaning 6Y-19

Replacement 6Y-20

Setting Dwell Angle 6Y-21

Distributor Condenser 6Y-22

Performance Diagnosis. 6Y-22

Replacement . . 6Y-23

Distributor

Breaker Point Type 6Y-23

Removal. . 6Y-23

Disassembly • 6Y-23
Page

Cleaning and Inspection .....'.., 6Y-25

Assembly . 6Y-25

Installation 6Y-26

Breakerless i 6Y-27

Removal . 6Y-27

Disassembly and Assembly 6Y-27

Installation 6Y-27

Off-Engine Test. . 6Y-27

Coil Replacement 6Y-27

Pulse Amplifier. 6Y-28

Disassembly .6Y-4S8

Component Checks
!
6Y-28

Assembly 6Y-29

Ignition Switch Replacement 6Y-29

Spark Plugs 6Y-30

Cleaning and Regapping I ....... 6Y-30

Installation . 6Y-31

GENERAL DESCRIPTION

There are two ignition systems available on 1967

vehicles. The breaker point type which is continued as

the regular production system and the optional (Corvette

only) transistor controlled breakerless ignition system

(magnetic pulse type). The transistor ignition system

features a specially designed distributor, control unit

(ignition pulse amplifier), and a special coil. Two resist-

ance wires are also used in the circuit; one as a ballast

between the coil negative terminal and ground, while the

other resistance wire provides a voltage drop for the

engine run circuit and is by-passed at cranking. The

other units in the system (the ignition switch, spark

plugs,
and battery) are of standard design. The dis-

tributor and control unit (ignition pulse amplifier) are

shown in Figures li and 2i.

CAP-

VACUUM

PICK-UP

COIL LEADS

PICK-UP COIL

CONNECTOR BODY
Although the external appearance of the distributor

resembles a standard distributor, the internal construc-

tion is quite different. As shown in the exploded view

(fig. 16i) an iron timer core replaces the conventional

breaker cam. The timer core has the same number of

equally-spaced projections, or vanes as engine cylinders.

The timer core rotates inside a magnetic pickup as-

sembly, which replaces the conventional breaker plate,

contact point set, and condenser assembly. The magnetic

pickup assembly consists of a ceramic permanent mag-

net, a pole piece, and a pickup coil. The pole piece
is.
a

steel plate having equally spaced internal teeth, one tooth

for each cylinder of the engine.

The magnetic pickup assembly is mounted over the

main bearing of the distributor housing, and is made to

rotate by the vacuum control unit, thus providing vacuum

advance. The timer core is made to rotate about the shaft

by conventional advance weights, thus providing centrifu-

gal advance.

Fig.
li—
Magnetic Pulse Distributor
Fig.
2i-lgnition Pulse Amplifier Unit

CHEVROLET CHASSIS SERVICE MANUAL

MAINTENANCE AND ADJUSTMENTS
ENGINE-ELECTRICAL 6Y-19

PERIODIC MAINTENANCE

BREAKER POINT SYSTEM

The distributor breaker points and spark plugs are the

only ignition system components that require periodic

service. The remainder of the ignition system requires

only periodic inspection to check operation of the units,

tightness of the electrical connections, and condition of

the wiring. When checking the coil, test with a reputable

tester.

Breaker type distributors are equipped with cam lubri-

cator and should have the wick replaced at the same time

contact point set is replaced. It is not necessary to

lubricate the breaker cam when using a cam lubricator.

Do not attempt to lubricate the wick - Replace when

necessary. When installing a new wick, adjust its posi-

tion so the end of the wick just touches the lobe of the

breaker cam.

Distributor shaft lubrication is accomplished by a

reservoir of lube around the mainshaft in the distributor

body.

BREAKERLESS SYSTEM

Since there are no moving parts in the ignition pulse

amplifier unit mounted forward of the radiator bulkhead,

and the distributor shaft and bushings have permanent

type lubrication, no periodic maintenance is therefore

required for the breakerless ignition system. The dis-

tributor lower bushing is lubricated by engine oil through

a splash hole in the distributor housing, and a housing

cavity next to the upper bushing contains a supply of

lubricant which will last between overhaul periods. At

time of overhaul, the upper bushing may be lubricated

by removing the plastic seal and then adding SAE 20 oil

to the packing in the cavity. A new plastic seal will be

required since the old one will be damaged during

removal.

Tachometer readings for test purposes can be made on

the primary circuit of the breakerless ignition system in

the same manner as on the conventional ignition system,

however before attempting to connect a test tachometer

into the primary circuit check with your instrument

supplier to insure that satisfactory readings can be

obtained and the breakerless system will not be damaged

by the tachometer that is to be used,

IGNITION COIL CHECK (BREAKERLESS)

The ignition coil primary can be checked for an open
PULSE

AMPLIFIER

IGN. SWITCH WIRE

"("IGN" TERMINAL)
-E3 IJU
12
WHITE-

-20 BLACKf' • 12 WHITE-

Fig.
3i—
Breakerless Ignition System

condition by connecting an ohmmeter across the two

primary terminals with the battery disconnected. Pri-

mary resistance at 75
°F.
should be between .35 and .55

ohm. An infinite reading indicates the primary is open.

For the engine to run but miss at times, the primary

open may be of the intermittent type.

The coil secondary can be checked for an open by con-

necting an ohmmeter from the high tension center tower

to either primary terminal. To obtain a reliable reading,

a scale on the ohmmeter having the 20,000 ohm value

within, or nearly within, the middle third of the scale

should be used. Secondary resistance at 75°F. should be

between
8,000
and 12,500 ohms. If the reading is infinite,

the coil secondary winding is open.

A number of different types of coil testers are avail-

able from various test equipment manufacturers. When

using these testers, follow the procedure recommended

by the tester manufacturer.

tester will properly
NOTE:
Make sure the

check this special coil.

SPARK PLUGS

Should be removed, inspected cleaned and regapped at

tune-up. Defective plugs should be replaced, see Servic-

ing of Units Off the Vehicle.

SERVICE OPERATIONS

DISTRIBUTOR CONTACT POINTS

CLEANING

Dirty contact points should be dressed with a few

strokes of a clean, fine-cut contact file. The file should

not be used for other metals and should not be allowed to

become greasy or dirty. Never use emery cloth to clean

contact points. Contact surfaces, after considerable use,

may not appear bright and smooth, but this is not neces-
sarily an indication that they are not functioning satis-

factorily. Do not attempt to remove all roughness nor

dress the point surfaces down smooth; merely remove

scale or dirt.

Badly burned or pitted contact points should be re-

placed and the cause of trouble determined so it can be

eliminated. High resistance or loose connections in the

condenser circuit, oil or foreign materials on the contact

surfaces, improper point adjustment or high voltages may

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-20

cause oxidized contact points. Check for these conditions

where burned contacts are experienced. An
out-of-

balance condition in the ignition system, often the result

of too much or too little condenser capacity, is indicated

where point pitting is encountered.

REPLACEMENT

Four and Six Cylinder Engine Distributor

1.
Release distributor cap hold-down screws, remove

cap and place it out of work area.

2.
Remove rotor.

3.
Pull primary and condenser lead wires from contact

point quick disconnect terminal (fig. 4i).

4.
Remove contact set attaching screw, lift contact point

set from breaker plate.

5.
Clean breaker plate of oil smudge and dirt.

6. Place new contact point assembly in position on

breaker plate, install attaching screw.

CAUTION: Carefully wipe protective film from

point set prior to installation.

NOTE: Pilot on contact set must engage match-

ing hole in breaker plate.

7.
Connect primary and condenser lead wires to quick

disconnect terminal on contact point set. .

8. Check and adjust points for proper alignment and

breaker arm spring tension (fig. 5i). Use an aligning

tool to bend stationary contact support if points need

alignment.

NOTE: The contact point pressure must fall

within specified limits. Weak tension will cause

CONTACT SET

ATTACHING

SCREW

QUICK

DISCONNECT

TERMINAL

BREAKER PLATE

ATTACHING SCREWS
chatter, resulting in arcing and burning of-the

points and an ignition miss at high speed, while

excessive tension will cause undue wear of the

contact points, cam and rubbing block. Breaker

arm spring tension should be 19-23 ounces. The

contact point pressure should be checked with a

spring gauge. The scale should be hooked to the

breaker lever and the pull exerted at 90 degrees

to the breaker lever as shown in Figure 5i. The

reading should be taken just as the points sepa-

rate.
The pressure can be adjusted by bending

the breaker lever spring. If the pressure is ex-

cessive, it can be decreased by pinching the

spring carefully. To increase pressure,, the

lever must be' removed from the distributor so

the spring can be bent away from the lever.

Avoid excessive spring distortion.

9. Set point opening (.019" for new points).

10.
Reinstall rotor, position and lock distributor cap to

housing.

11.
$tart engine and test dwell and ignition timing.

Eight Cylinder Engine Distributor

1.
The contact point set is replaced as one complete

assembly and only dwell angle requires adjustment

after replacement. Breaker lever spring tension and

point alignment are factory set.

2.
Remove the distributor cap by placing a screw driver

in the slot head of the latch, press down and turn 1/4

turn in either direction.

3.
Remove the two attaching screws which hold the base

of the contact set assembly in place.

4.
Remove the primary and condenser leads from their

nylon insulated connection (fig. 6i) in contact set.

5.
Reverse Steps 2, 3 and 4 to install new contact set.

CAUTION:. Install the primary and condenser

leads as shown in Figure 6i. Improper installa-

tion will cause lead interference between the

cap,
weight base and breaker advance plate.

6. If car has 20,000 to 25^000 miles (or sooner if

desired) the cam lubricator wick (fig. 7i) should be

changed. Using long nosed pliers squeeze assembly

together at base and lift out. Remove all old lubri-

cant from cam surface. Replace in same manner.

Fig.
4i—Breaker Plate and Attaching Parts
Fig. 5i—-Checking Breaker Arm Spring Tension

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL
6Y-21

Fig.
6i—Distributor Lead Arrangements

NOTE:
End of cam
lubricant wick should
be

adjusted
to
just touch
cam
lobes. Over lubrica-

tion
of cam
resulting
in
grease
on
contact points

can-
be
caused
by cam
lubrication wick bearing

too hard against
cam
surface.
A
correctly
ad-

justed
cam
lubricator wick will provide adequate

lubrication
for cam. Do not
apply additional

grease
to cam
surface.

7.
Start engine
and
check point dwell
and
ignition

timing.
ACTUAL
POINT OPENING
.021

.016
FEELER GAUGE

LOCATOR ___JH^H

(ROUND)
V~^3H|

CENTRIFUGAL
\
jdft

ADVANCE
-~-»JBlMBl

MECHANISM
«H

CAM g^k. / X

LUBRICATOR
V^^^

REPLACEMENT
^£9

^-ADJUST
SQUARELY

AND
JUST

TOUCHING
LOBE

OF
CAM
.ROTOR

I^^I^BL
LOCATOR

(PBV 7
(SQUARE)

SBSSF
/

WWjga^/
^/
LUBRICATOR

H^f
CAUTION!

S5y
NEVER
OIL

•-^
CAM
LUBRICATOR-

REPLACE
WICK

WHEN
NECESSARY
Fig.
8i—Inaccurate Gauging
of
Rough Points

SETTING DWELL ANGLE

Four
and Six
Cylinder Engine Distributors

The point opening
of new
points
can be
checked with
a

feeler gauge,
but the use of a
feeler gauge
on
rough
or

uncleaned used points
is not
recommended since accurate

mechanical gauging cannot
be
done
on
such points (fig. 8i).

Contact points must
be set to the
proper opening.

Points
set too
close
may
tend
to
burn and
pit
rapidly.

Points with excessive separation tend
to
cause
a
weak

spark
at
high speed. Proper point setting
for all

models
are:

.019"
for new
points

.016"
for
used points

New points must
be set to the
larger opening
as the

rubbing block will wear down slightly while seating
to the

cam. Contact points should
be
cleaned before adjusting
if

they have been
in
service.

LATERAL

MISALIGNMENT
PROPER

LATERAL
ALIGNMENT

pCORRECT
LATERAL MISALIGNMENT
BY

M
BENDING FIXED CONTACT SUPPORT

[NEVER
BEND BREAKER LEVER

Fig.
7i—Top View
of
Distributor

Fig.
9i—Alignment
of
Points

CHEVROLET
CHASSIS SERVICE /MANUAL

ENGINE-ELECTRICAL 6Y-22

ADJUST DWELL

ANGLE SETTING OR

POINT OPENING

Fig.
lOi—Settihg Point Opening

To adjust the contact point opening:

1.
If necessary, align points (fig. 9i) by bending the

fixed contact support. Do not bend the breaker lever.

Do not attempt to align used points; replace them

where serious misalignment is observed. Use an

aligning tool if available.

2.
Turn or crank the distributor shaft until the breaker

arm rubbing block is on the high point of the cam

lobe.
This will provide maximum point opening.

3.
Loosen the contact support lock screw.

4.
Use a screw driver (fig. lOi) to move the point sup-

port to obtain a .019" opening for new points and a

.016"
opening for used points.

5.
Tighten the contact support lock screw and recheck

the point opening.

6. After checking and adjusting the contact point open-

ing to specifications, the cam angle or dwell should

be checked with a dwell angle meter if such equip-

ment is available (see Specifications for proper dwell

angle).
If the cam angle is less than the specified

minimum, check for defective or misaligned contact

points or worn distributor cam lobes. The variation

in cam angle readings between idle speed and 1750

engine rpm should not exceed 3°. Excessive varia-

tion in this speed range indicates wear- in the

distributor.

NOTE:
Cam angle readings taken at speeds

above 1750 engine rpm may prove unreliable

on some cam angle meters.

Eight Cylinder Engine Distributor

On the Vehicle

With the engine running at idle and operating tempera-

tures normalized, the dwell is adjusted by first raising

the window provided in the cap and inserting a "Hex"

type wrench into the adjusting screw head (fig. Hi).
WINDOW

r- "HEX" TYPE

WRENCH

ADJUSTING

SCREW

Fig.
-lli—Adjusting Dwell Angle

1.

Preferred Method - Turn the adjusting screw until

the specified dwell angle is obtained as measured in

degrees (28° to 32°, 30° preferred) by a dwell angle

meter.

2.
Alternate Method - Turn adjusting screw in (clock-

wise) until the engine begins to misfire, then turn

screw 1/2 turn in the opposite direction (counter-

clockwise). This will give the approximate dwell

angle required. (Use only when meter is not

available.)

Off the Vehicle

1.
Distributor Test Method:

a. With the distributor mounted on a distributor

testing machine, connect the dwell meter to the

distributor primary lead.

b.
Turn the adjusting screw (fig. lli) to set the dwell

angle to 30 degrees.

2.
Test Light Method:

a. With the distributor mounted in a vise, connect a

testing lamp to the primary lead.

b.
Rotate the shaft until one of the circuit breaker

cam lobes is under the center of the rubbing block

of the breaker lever.

c. Turn the adjusting screw clockwise (fig. lli) until

the lamp lights, then give the wrench 1/2 turn in

the opposite direction (counter-clockwise) to ob-

tain the proper dwell angle.

DISTRIBUTOR CONDENSER

PERFORMANCE DIAGNOSIS

The following four factors affect condenser perform-

ance,
and each factor must be considered in making any

condenser test.

1.
Breakdown - A failure of the insulating material. A

direct short between the metallic elements of the

condenser. This prevents any' condenser action.

2.
Low Insulating Resistance (Leakage) - Low insula-

tion resistance prevents the condenser from holding

a charge. All condensers are subject to leakage

which, up to a certain limit, is not objectionable.

3.
High Series Resistance - Excessive resistance in

the condenser circuit due to broken strands in the

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-23

condenser leak or to a defective connection. This

will cause burned points and ignition failure upon

initial starts and at high speeds.

4.
Capacity - Capacity is determined by the area of

the metallic elements and the insulating and im-

pregnating materials.

For a complete check of the condenser, use a tester

which will check for all of the above conditions. Follow

the instructions given by the manufacturer of the

test equipment. Condenser capacity should be
.18-:
23

microfarads.

REPLACEMENT

Four and Six Cylinder Engine Distributor (Fig. 4i)

1.
Release distributor cap hold-down screws, remove

cap and place it out of the work area.

2.
Remove rotor.

3.
Disconnect condenser lead wire from contact point

quick-disconnect terminal.

4.
Remove condenser attaching screw, lift.condenser

from breaker plate and wipe breaker plate clean.

5. Install new condenser using reverse of procedure

outlined above.

Eight Cylinder Engine Distributor

1.
Remove distributor cap.

2.
Loosen condenser lead attaching screw (fig. 6i) and

lift out condenser lead clip.

3.
Remove screw holding condenser bracket to breaker

plate and slide condenser from bracket.

4.
To replace condenser reverse the above procedure.

NOTE:
Make sure that new condenser lead is

installed in proper position (fig. 6i).

DISTRIBUTOR

(BREAKER POINT TYPE)

REMOVAL

1.
On radio equipped Corvettes, remove ignition shield

from over distributor and coil. One bolt is accessible

from top of shield, the other two are at rear of

shield, facing firewall.

2.
Release the distributor cap hold-down screws, re-

move the cap and place it clear of the work area.

NOTE:
If necessary, remove secondary leads

from the distributor cap after first marking the

cap tower for the lead to No. 1 cylinder. This

will aid in the reinstallation of leads in the cap.

3.
Disconnect the distributor primary lead from the coil

terminal.

4.
Scribe a realignment mark on the distributor bowl

and engine in line with the rotor segment.

5. Disconnect vacuum line to distributor and tachometer

drive cable (Corvette). Remove the distributor hold-

down bolt and elamp and remove the distributor from

the engine. Note position of vacuum advance mecha-

nism relative to the engine.

CAUTION: Avoid rotating the engine with the

distributor removed as the ignition timing will

be upset.
Rg.
121-L-6 Distributor-Exploded View

1.
Breaker Plate Attaching

Screws

2.
Condenser Attaching

Screws

3. Condenser

4.
Breaker Plate Assembly

4a.
Cam Lubricator

5. Vacuum Control Assembly

6. Vacuum Control

Attaching Screws

7. Housing

8. Cap

9. Rotor

DISASSEMBLY
10.
Contact Point

Attaching Screw

11.
Contact Point Assembly

12.
Weight Cover

Attaching Screws

13.
Weight Cover

14.
Weight Springs

15.
Advance Weights

16. Cam Assembly

17.
Main Shaft Assembly

18.
Roll Pin

19.
Drive Gear

It is advisable to place the distributor in a distributor

testing machine or synchroscope prior to disassembly.

CHEVROLET CU
SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-24

Fig.
13I-V-8 Distributor (Typical)-Exploded View

1.

2.

2a.

3.

4.
Condenser

Contact Point Assembly

Cam Lubricator

Retaining Ring

Breaker Plate
5.

5a.

6.

7.
Felt Washer

Plastic Seal

Vacuum Advance

Unit

Housing
8.^
Shim
Washer

9. Drive Gear Pin

10.
Drive Gear

11.
Cap

12.
Rotor
13.
Weight Springs

14.
Mainshaft

15.
Advance Weights

16.
Cam Weight

Base Assembly

When mounting distributors for tests, first secure the

gear in the test drive mechanism, then push the distribu-

tor housing downward toward the gear to take up any end

play between the gear and the housing.

NOTE:
When testing distributors that have

their lower shaft support bushing located in the

engine block (6 cylinder engines), a special

adapter should be used to insure the shaft will

run true in its housing.

Test the distributor for variation of spark, correct

centrifugal and vacuum advance and condition of contacts.

This test will give valuable information on distributor

condition and indicate parts replacement which may be

necessary. Check the area on the breaker plate just

beneath the contact points. A smudgy line indicates that

oil or crankcase vapors have been present between the

points.

Four and Six Cylinder Engines

Refer to Figure 12i.

1.
Remove the rotor.
2.

3.
Remove the vacuum control assembly retaining

screws, detach the unit from the distributor housing.

Disconnect the primary and condenser leads from the

contact point quick disconnect terminal, remove the

contact point set attaching screw, condenser attach-

ing screw. Remove the point set and condenser from

the breaker plate.

Remove the breaker plate attaching screws, remove

the breaker plate from the distributor housing (fig.

NOTE:
Do not disassemble breaker plate any

further.

5. Remove the roll pin retaining the driven gear to the

mainshaft, slide the gear from the shaft.

6. Slide the cam and mainshaft from the distributor

housing.

7. Remove the weight cover, and stop plate screws, re-

move the cover, weight springs, weights and slide

cam assembly from the mainshaft.

V-8 Engines

Refer to Figure 13i.

CHEVROLET CHASStS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-25

1.
Remove the rotor.

2.
Remove both weight springs and advance weights.

3.
Remove roll pin retaining driven gear to distributor

shaft, slide the gear and spacers from the shaft.

Remove tachometer drive gear on Corvette models.

4.
Before sliding the distributor shaft from the hous-

ing, check for and remove any burrs on the shaft.

This will prevent damage to the seals and bushing

still positioned in the housing.

5. Slide the distributor mainshaft and cam-weight base

assembly from the housing.

6. Remove vacuum advance mechanism retaining

screws, remove the vacuum advance assembly.

7. Remove the spring retainer, remove the breaker

plate assembly from the distributor housing. Re-

move the contact point and condenser from the

breaker plate. Remove the felt washer and plastic

seal located beneath the breaker plate.

CLEANING AND INSPECTION

1.
Wash all parts in cleaning solvent except cap, rotor,

condenser, breaker plate assembly and vacuum con-

trol unit. Degreasing compounds may damage insula-

tion of these parts or saturate the lubricating felt in

the case of the breaker plate assembly.

2.
Inspect the breaker plate assembly for damage or

wear and replace if necessary.

3.
Inspect the shaft for wear and check its fit in the

bushings in the distributor body. If the shaft or bush-

ings are worn, the parts should be replaced.

4.
Mount the shaft in "V" blocks and check the shaft

alignment with a dial guage. The run-out should not

exceed .002".

5. Inspect the advance weights for wear or burrs and

free fit on their pivot pins.

6. Inspect the cam for wear or roughness. Then check

its fit on the end of the shaft. It should be absolutely

free without any roughness.

7. Inspect
the •
condition of the distributor points. Dirty

points should be cleaned and badly pitted points

should be replaced. (See Distributor Contact Points.)

8. Test the condenser for series resistance, micro-

farad capacity (.18 to .23) and leakage or breakdown,

following the instructions given by the manufacturer

of the test equipment used.

9. Inspect the distributor cap and sparkplug wires for

damage and replace if necessary.

ASSEMBLY

Four and Six Cylinder Engine

Refer to Figure 12i for Exploded View of Distributor.

1.
Replace cam assembly to mainshaft.

NOTE:
Lubricate top end of shaft with Delco

cam and ball bearing grease or equivalent prior

to replacing.

2.
Install governor weights on their pivot pins, replace

weight springs. Install weight cover and stop plate.

3.
Lubricate mainshaft and install it in distributor

housing.

4.
Install distributor driven gear to mainshaft and in-

sert attaching roll pin. Check to see that shaft turns

freely.
5. Install breaker plate assembly in the distributor body

and attach retaining screws.

6. Attach condenser and contact point set in proper lo-

cation with appropriate attaching screws.

NOTE:
Contact point set pilot must engage

matching hole in breaker plate. Connect primary

and condenser leads to contact set quick-

disconnect terminal.

7. Attach vacuum control assembly to distributor

housing.

8. Check and adjust contact point opening and align-

ment (See setting and alignment of points.)

9. Check breaker lever spring tension which should

be.
19-23 ounces. (See contact point replacement.)

V-8 Assembly-(Fig. 13i)

1.
Fill housing lubricating cavity with proper compound,

press in new plastic seal and install felt washer.

2.
Replace the vacuum advance unit, install the breaker

plate in housing and install the spring retainer on

the upper bushing.

3.
Lubricate and slide weight cam over mainshaft and

install weights and spring (fig. 14i).

4.
Insert mainshaft into housing, indexing it with drive

gear and washers. Install tachometer drive gear on

Corvette models.

5. Slide distributor drive gear shims and gear over

shaft and install new pin. Tap new pin through gear

and mainshaft. Check shaft for free rotation.

NOTE:
Mainshaft end clearance should be

.002"-.007". Add or remove shims as necessary.

6. Install contact point set and condenser to breaker

plate. Connect leads as shown in Figure 6i.

NOTE:
Contact point spring tension is factory-

set above specifications to assure ease of final

adjustment. Correct tension is 19-23 oz.

7. Install rotor to cam assembly, indexing round and

square pilot holes.

Flg.
Hi-Advance Weights Installed

CHEVROLET CHASSIS SERVICE