display CHRYSLER VOYAGER 2001 Owner's Manual

Symptom:
ORC, CALIBRATION MISMATCH - ACTIVE
When Monitored and Set Condition:
ORC, CALIBRATION MISMATCH - ACTIVE
When Monitored: With ignition on, the ORC monitors the PCI Bus for the VIN message
containing the body style. The PCM transmits the complete VIN message every 14 seconds.
Note: The VIN message should match the vehicle VIN plate.
Set Condition: If the Body style stored in ORC does not exactly match the vehicle body
style indicated by the PCM, then the fault shall be set.
POSSIBLE CAUSES
PCM, PCI COMMUNICATION FAILURE
COMPARE VEHICLE IDENTIFICATION NUMBERS
ORC, ORC CALIBRATION MISMATCH
TEST ACTION APPLICABILITY
1 Turn the ignition on.
Connect the DRB to the data link connector and select PASSIVE RESTRAINTS,
AIRBAG, SYSTEM TEST.
With the DRBIIIt, read the system test.
Does the DRB show PCM Active on the Bus:?All
Ye s®Go To 2
No®Refer to category COMMUNICATION CATEGORY and select the
related symptom.
Perform AIRBAG VERIFICATION TEST - VER 1.
2 With the DRB select ENGINE MISCELLANEOUS, select MISC FUNCTION, and
then CHECK VIN to read the Vehicle Identification Number in the Powertrain
Control Module.
Compare the VIN displayed on the DRB screen and the Vehicle VIN plate.
Does the VIN plate and the PCM VIN match?All
Ye s®Go To 3
No®Replace the Powertrain Control Module and program with the
correct vehicle identification number.
Perform AIRBAG VERIFICATION TEST - VER 1.
73
AIRBAG

Symptom:
ORC, CLUSTER MESSAGE MISMATCH - ACTIVE
When Monitored and Set Condition:
ORC, CLUSTER MESSAGE MISMATCH - ACTIVE
When Monitored: After the MIC bulb test is completed, the ORC compares the Lamp
Request by ORC, On or Off, and the Lamp on by MIC, On or Off, PCI Bus messages. Each
message is transmitted one time per second or when a change in the lamp state occur.
Set Condition: If the Lamp Request by ORC, On or Off, and the Lamp on by MIC, On or
Off, messages do not match, the code will set.
POSSIBLE CAUSES
MIC, COMMUNICATION FAILURE
MIC, CLUSTER MESSAGE MISMATCH
ORC, CLUSTER MESSAGE MISMATCH
TEST ACTION APPLICABILITY
1 Turn the ignition on.
With the DRBIIIt, ensure PCI Bus communications with the Instrument Cluster.
Is the Instrument Cluster communicating on the PCI Bus?All
Ye s®Go To 2
No®Refer to category COMMUNICATION CATEGORY and select the
related symptom INSTRUMENT CLUSTER BUS +/- SIGNAL
OPEN.
Perform AIRBAG VERIFICATION TEST - VER 1.
2 With the DRB select PASSIVE RESTRAINTS, AIRBAG, MONITOR DISPLAY and
WARNING LAMP STATUS.
Cycle the ignition key and observe the LAMP ON BY MIC and LAMP REQ BY ORC
monitors after the 6 to 8 second indicator test.
Does the LAMP ON BY MIC and LAMP REQ BY ORC monitors match?All
YES
Go To 3
NO
Replace Mechanical Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.
82
AIRBAG

Symptom:
ORC, DRIVER SBT CIRCUIT OPEN - ACTIVE
When Monitored and Set Condition:
ORC, DRIVER SBT CIRCUIT OPEN - ACTIVE
When Monitored: When the ignition is On, the ORC monitors the resistance of the Driver
Seat Belt Tensioner circuits.
Set Condition: The ORC has detected an open circuit or high resistance on the Driver
Seat Belt Tensioner circuits.
POSSIBLE CAUSES
DRIVER SBT CIRCUITS OPEN
DRIVER SBT LINE 1 CIRCUIT OPEN
DRIVER SBT LINE 2 CIRCUIT OPEN
ORC, DRIVER SBT CIRCUITS OPEN
TEST ACTION APPLICABILITY
1NOTE: Ensure the battery is fully charged.
WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
Disconnect the Driver SBT.
NOTE: Check connectors - Clean and repair as necessary.
Connect the SRS Load Tool 8443 Passenger cable and jumper to the Driver SBT
connector.
WARNING: TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIIIt, read the active DTC's.
Does the DRBIIItdisplay DRIVER SBT CIRCUIT OPEN?All
Ye s®Go To 2
No®Replace Driver Seat Belt Tensioner.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
90
AIRBAG

Symptom:
ORC, DRIVER SBT CIRCUIT SHORT - ACTIVE
When Monitored and Set Condition:
ORC, DRIVER SBT CIRCUIT SHORT - ACTIVE
When Monitored: When the ignition is on, the ORC monitors the resistance of the Driver
Seat Belt Tensioner circuits
Set Condition: The ORC has detected low resistance in the Driver Seat Belt Tensioner
circuits.
POSSIBLE CAUSES
DRIVER SBT CIRCUITS SHORT
DRIVER SBT LINE 1 SHORT TO LINE 2
ORC, DRIVER SBT CIRCUIT SHORT
TEST ACTION APPLICABILITY
1NOTE: Ensure the battery is fully charged.
WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
Disconnect the Driver SBT connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the SRS Load Tool 8443 Passenger cable and jumper to the Driver SBT
connector.
WARNING: TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIIIt, read the active DTC's.
Does the DRBIIItdisplay DRIVER SBT CIRCUIT SHORT?All
Ye s®Go To 2
No®Replace Driver Seat Belt Tensioner.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
92
AIRBAG

Symptom:
ORC, DRIVER SBT SHORT TO BATTERY - ACTIVE
When Monitored and Set Condition:
ORC, DRIVER SBT SHORT TO BATTERY - ACTIVE
When Monitored: When the ignition is on, the ORC monitors the voltage of the Driver
Seat Belt Tensioner circuits.
Set Condition: The ORC has detected high voltage on the Driver Seat Belt Tensioner
circuits.
POSSIBLE CAUSES
DRIVER SBT CIRCUITS SHORT TO BATTERY
DRIVER SBT LINE 1 SHORT TO BATTERY
DRIVER SBT LINE 2 SHORT TO BATTERY
ORC, DRIVER SBT CIRCUITS SHORT TO BATTERY
TEST ACTION APPLICABILITY
1WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
Disconnect the Driver SBT.
NOTE: Check connectors - Clean and repair as necessary.
Connect the SRS Load Tool 8443 Passenger cable and jumper to the Driver SBT
connector.
WARNING: TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIIIt, read the active DTC's.
Does the DRBIIItdisplay DRIVER SBT SHORT TO BATTERY?All
Ye s®Go To 2
No®Replace Driver Seat Belt Tensioner.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
94
AIRBAG

Symptom:
ORC, DRIVER SBT SHORT TO GROUND - ACTIVE
When Monitored and Set Condition:
ORC, DRIVER SBT SHORT TO GROUND - ACTIVE
When Monitored: When the ignition is on, the ORC monitors the voltage of the Driver
Seat Belt Tensioner circuits.
Set Condition: The ORC has detected a short to ground in the Driver Seat Belt Tensioner
circuits.
POSSIBLE CAUSES
DRIVER SBT CIRCUITS SHORT TO GROUND
DRIVER SBT LINE 1 SHORT TO GROUND
DRIVER SBT LINE 2 SHORT TO GROUND
ORC, DRIVER SBT CIRCUITS SHORT TO GROUND
TEST ACTION APPLICABILITY
1WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
Disconnect the Driver SBT connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the SRS Load Tool 8443 Passenger cable and jumper to the Driver SBT
connector.
WARNING: TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIIIt, read the active DTC's.
Does the DRBIIItdisplay DRIVER SBT SHORT TO GROUND?All
Ye s®Go To 2
No®Replace the Driver Seat Belt Tensioner.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
96
AIRBAG

Symptom:
ORC, NO CLUSTER MESSAGE - ACTIVE
When Monitored and Set Condition:
ORC, NO CLUSTER MESSAGE - ACTIVE
When Monitored: With the ignition in the On position, the ORC monitors the PCI Bus for
a message from the MIC containing the airbag warning lamp status. The MIC transmits
the message one time at ignition on, lamp state change, or in response to the ORC lamp
message.
Set Condition: If the MIC message is not received for 10 consecutive seconds, the code
will set.
POSSIBLE CAUSES
MIC, COMMUNICATION FAILURE
NO CLUSTER MESSAGES
ORC, NO CLUSTER MESSAGES
TEST ACTION APPLICABILITY
1 Turn the ignition on.
With the DRBIIIt, ensure PCI Bus communications with the Instrument Cluster.
Is the Instrument Cluster communicating on the PCI Bus?All
Ye s®Go To 2
No®Refer to category COMMUNICATION CATEGORY and select the
related symptom INSTRUMENT CLUSTER BUS +/- SIGNAL
OPEN.
Perform AIRBAG VERIFICATION TEST - VER 1.
2 With the DRB select PASSIVE RESTRAINTS, AIRBAG, MONITOR DISPLAY and
WARNING LAMP STATUS.
Cycle the ignition key and observe the LAMP ON BY MIC monitor after the 6 to 8
seconds bulb check.
Does the DRB show LAMP ON BY MIC: ON or OFF?All
YES
Go To 3
NO
Replace Instrument Cluster circuit board.
Perform BODY VERIFICATION TEST - VER 1.
126
AIRBAG

Symptom:
ORC, NOT CONFIGURED FOR SAB - ACTIVE
When Monitored and Set Condition:
ORC, NOT CONFIGURED FOR SAB - ACTIVE
When Monitored: With ignition on, the ORC monitors the PCI Bus for a message
containing an9A9in the 4 th position of the VIN. This character identifies the type of safety
equipment and should match the VIN. The PCM transmits the VIN every 13.76 seconds.
Set Condition: The code will set, if the ORC detects a Side Impact Airbag Module active
on the PCI Bus and the 4 th character of the VIN message is not an9A9.
POSSIBLE CAUSES
PCM, PCI COMMUNICATION FAILURE
CHECK PCM VIN
ORC, ORC NOT CONFIGURED FOR SIDE AIRBAGS
TEST ACTION APPLICABILITY
1 Turn the ignition on.
Connect the DRB to the data link connector and select PASSIVE RESTRAINTS,
AIRBAG, SYSTEM TEST
With the DRBIIIt, read the PCM Active on the Bus
Does the DRB show PCM Active on the Bus:?All
Ye s®Go To 2
No®Refer to category COMMUNICATION and select the related
symptom.
Perform AIRBAG VERIFICATION TEST - VER 1.
2 With the DRB read the Vehicle Identification Number in the Powertrain Control
Module.
Compare the VIN displayed on the DRB screen and the Vehicle VIN plate.
Does the VIN plate and the PCM VIN match?All
Ye s®Go To 3
No®Replace the Powertrain Control Module and program with the
correct vehicle identification number.
Perform AIRBAG VERIFICATION TEST - VER 1.
132
AIRBAG

Symptom:
ORC, PASSENGER SBT CIRCUIT OPEN - ACTIVE
When Monitored and Set Condition:
ORC, PASSENGER SBT CIRCUIT OPEN - ACTIVE
When Monitored: When the ignition is On, the ORC monitors the resistance of the
Passenger Seat Belt Tensioner circuits.
Set Condition: The ORC has detected an open circuit or high resistance or open circuit in
the Passenger Seat Belt Tensioner circuits.
POSSIBLE CAUSES
PASSENGER SBT CIRCUITS OPEN
PASSENGER SBT LINE 1 CIRCUIT OPEN
PASSENGER SBT LINE 2 CIRCUIT OPEN
ORC, PASSENGER SBT CIRCUITS OPEN
TEST ACTION APPLICABILITY
1NOTE: Ensure the battery is fully charged.
WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
Disconnect the Passenger SBT connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the SRS Load Tool 8443 Passenger cable and jumper to the Passenger SBT
connector.
WARNING: TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIIIt, read the active DTC's.
Does the DRBIIItdisplay PASSENGER SBT CIRCUIT OPEN?All
Ye s®Go To 2
No®Replace the Passenger Seat Belt Tensioner in accordance with the
Service Information.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
141
AIRBAG

Symptom:
ORC, PASSENGER SBT SHORT TO BATTERY - ACTIVE
When Monitored and Set Condition:
ORC, PASSENGER SBT SHORT TO BATTERY - ACTIVE
When Monitored: When the ignition is on, the ORC monitors the voltage of the Passenger
Seat Belt Tensioner circuits.
Set Condition: The ORC has detected high voltage on the Passenger Seat Belt Tensioner
circuits.
POSSIBLE CAUSES
PASSENGER SBT CIRCUITS SHORT TO BATTERY
PASSENGER SBT LINE 1 SHORT TO BATTERY
PASSENGER SBT LINE 2 SHORT TO BATTERY
ORC, PASSENGER SBT CIRCUITS SHORT TO BATTERY
TEST ACTION APPLICABILITY
1WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
Disconnect the Passenger SBT connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the SRS Load Tool 8443 Passenger cable and jumper to the Passenger SBT
connector.
WARNING: TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIIIt, read the active DTC's.
Does the DRBIIItdisplay PASSENGER SBT SHORT TO BATTERY?All
Ye s®Go To 2
No®Replace the Passenger Seat Belt Tensioner, SBT, in accordance
with the Service Information.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.
145
AIRBAG